I have upgraded to WM2003SE ROM, and upgraded Radio ROM to A20.10. My device is PH10A. But when I insert a sim card, these always no GSM, I could not dial any phone call.
Could anyone tell me that I should flash which Radio ROM to my device? Thanks
problem connecting to any network after radio upgrade
Hi,
I am having the same problem connecting to any cell network on my phone. It is a Qtek 1020 PW10A1 Rom version 4.02.04 ENG.
The problem started after updating the Radio stack software. The signal icon always shows up as no signal, this happens on all networks. I have another 1020 with the same Rom version but a different radio version A33.02 that is working. I have tried to search for this version to download or a solution for this problem for a few days now with no luck and was wondering if any one could help?
I have come across many other radio versions that say they are compatible with this model but each produce the same result, no signal.
Thanks in advance
(PS this is my first post!)
Hi Shadow,
I also have a 1020 with RSU 33.02 installed. If I knew how to extract the RSU then I could upload it here. It could do with being on the FTP. I didn't find anything on the Wiki about it, wondering if anyone has any suggestions?
Regards,
Neil.
I’m new to this so this may be wrong but I have found out that if I go into the wallaby boot loader and push the contacts button I get these options:
CE ROM TO SD
BOOT TO SD
GSM ROM TO SD
CE+GSM TO SD
Is the “GSM ROM TO SD” option the one that’s needed to be able to get the RSU extracted or is this something completely different?
When I select it, it tells me to connect the rs232 and run pc monitor – two things I don’t have.
Shadow1
Anyone found RSU 33.02 rom yet? or have any sugestions on how i could fix my phone :?:
Thanks
Hello All,
I recently got an ATT 8525 and I'm trying to use it with my T-Mobile (US) SIM. I was able to successfully unlock the SIM and CID with an util/rom I found on this site (I think the post was from Pof). And I also re-flashed the phone with the latest ROM available.
But after about 5-10mins of usage the signal dies and when I reboot it says No GSM. Looks like the Radio ROM gets corrupted. I tried just re-flashing the Radio ROM and that doesn't help either. It works for short while and again the signal dies.
And also, I'm unable to install any of the generic ROMs (Fantastic Mobiz, PVET 40005) Although I'm connected to Active Sync when I run the Step 1 (ROMUpdateUtility_NV_G3.exe), I get a ERROR [222] : DEVICE NOT RESPONDING. And when I run the step 2 directly (update_rom.bat) I get an cannot update itsutils.dll maybe in use error.
As you can tell I've been messing with phone a lot for a couple of days with no luck and my frustration level is kinda high
As of now here’s where I stand. I re-flashed the phone (Image: 3.62, Radio 1.50) and it’s on the “Tap the screen to set up your windows based mobile device” screen. I plan on leaving it on this screen until I can a good solution.
I would like to get rid of the ATT ROM and install one of those hybrid generic ROM that is not Carrier specific. Any help will be much appreciated. Share your ideas, I’m very experimental
Phone Details…
ATT 8525
HERM100
IPL: 1.04
SPL: 1.40.0 lipro
Hi everyone !
I'm new here (in the Hermes forums). I have a prophet, but now I bought a Hermes.
The guy who originally owned (the phone is used) told me that when he flashed it, he had this problem that I'm going to tell you now, so I really don't know what could had happened to him during the flashing process.
The problem I have is that the Hermes works very well, the Wifi, bluetooth, card reader, everything EXCEPT the PHONE, let's say, the GSM interface.
When I turn it on, everything works well, (I DON'T SEE THE 'NO GSM' THING), and I have the antenna icon with the exclamation mark (!) next to it. When I go into there, in the phone configuration, if I try to select a network manually, after a few seconds it says that it can't retrieve the list of networks, that I have to try later. If I go to the band configuration, and I put it to use only gsm, for example, after a few seconds it says that it can't change the configuration, that I have to try later.
I tryed with different sims, of different companies.
When I bought the phone, it had a spanish Schap's 3.54b, and the Olipro 2.30 spl.
I tryed hard resetting, but nothing. I flashed the original shipped rom WM6.1 WWE, downloaded from here, and nothing. NOTE: I had to flash with the sd method because if I try to do it with the computer, I have the 260 error (or 262 i dont remember).
I changed the HARDSPL to theOlipro 2.10, hard reseted again, and still de same thing.
The IPL is 1.04.
NOTE: When I flashed the WWE rom, I flashed the .nbf file inside, but the SPL.nbf I didn't flashed.
What can I do? ANY SUGGESTIONS ?
I read a lot of things in the forums and in the wiki, but nothing. I've just finished downloading the Schaps WM6 4.31, now i will try to flash it with the sd thing.
Also, I have the protocol 32.80.7020.20H. I've read it somewhere but I don't remember what the protocol is. I HAVEN'T CHANGED THIS since I bought it, could that be my problem?
Currently, I have this (before flashing Schaps):
-Device Information:
ROM: 3.54.255.3
ROM DATE: 07/05/07
Radio Version: 1.47.00.10
Protocol: 32.80.7020.20H
ExtROM: 3.54.255.104
-In the bootloader:
IPL-1.04
SPL-2.10.Olipro
Maybe the antenna is no good...
1st thing I'd try though is to flash a new radio on (use sd card method). Worst that can happen is "No GSM" but as you can't use it anyway theres no harm in trying...
Check what radio rom you have 1st though so you can flash back if need be.
If you can get a "broken" Hermes (same model is best) then you can replace parts and see if that helps. I did this and found one of the parts that was causing a problem with my jasjam was the flywheel.
Do a search for the HTC service manual or go to Mike Channons web site to get heaps of manuals and tutorials...
Cheers...
The phone is near new, let's say, it was used for less than a month, he had it a week or two and then flashed it and had that problem, so I don't think that it's and antenna problem, and if it hadn't antenna, it has some signal of some kind.
Any other ideas?
I changed the radio when i Flashed the WWE version. I'm now downloading this one http://forum.xda-developers.com/showthread.php?t=298520
Any suggestions? is there any problem using the AKU 3 or something?
Thanks =)
Hey,
What about the protocol version? can I change it? how? cause I flashed it and the radio changed but the protocol is the same.
I'll try to flash it with windows vista, to see if I can, because XP won't let my.. olnly SD flashing
Ok, I Installed a cingular flash, now I've protocol 32.67.7020.10H. Radio:1.34.00.10 and still having the same problem. I don't know what to do now... any suggestions? !
thanks
PD: also tryed putting a little piece of paper over the sim but it didn't changed anything
PD2: The error I get when I go to Phone Settings -> Netowrk, and I choose "Manual" is: "Unable to read setting from the netowrk. Try viewing settings later, or disconnect data connection and try again.
Now I know this is a novas question at best and its probable been covered already but I don’t know how to fix this. First I was experiencing what I believe to be radio issues, like I had a fully functional sim card in my Hermes but I was not receiving and service anywhere, only had this problem with the Hermes other phones where fine. I tried to do the wm6 rom update but I kept getting an error I think it was 262, so then I downloaded spl 2.10 in an effort to just update the radio, and as I went one to install radio rom 1.40 I kept e getting another error and now my Hermes has been stuck in the boot loader for 2 days, can someone please tell me how to get out of the boot loader and how to get my radio working again.
Hello All,
I upgraded my EXEC to WM6 with the ROM of lucathebig. I did not upgrade the radio rom.
I don't know how it happened but, every time I switch it on, even without the sim card in, I can't access the phone settings! Or even the dialpad for that matter.
When I click on the signal icon, the balloon comes on but says "The phone is off"
When I tap settings nothing happens.
Please note that it was working a couple of days ago. I reset it to factory defaults but nothing happened.
Has anyone else got any suggestions? I will try to avoid flashing the ROM again and I'll keep it as the last option.
Update:
I noticed that there's no Radio version or IMEI on the system information on my phone so I figured that the radio got corrupted or something like that.
I tried to flash the Radio but i get the 114 error from the upgrade tool.
I tried all sorts of different upgrade tools with different radio version but none of it worked...
I am now downloading the official O2 update Xda_Exec_Upgrade_v113188.exe and try to install this instead to see if it fixes the Radio.
Has anyone found a solution for the 114 error? I have read tens of posts but can't seem to fins anything that helps. The people who solve it, use different versions of the update tools or they remove the USB hubs or try the upgrade 3 times.
Help ..?
I tried O2 update but the upgrade executable gave me a country ID error.
So I took the WM ROM and the Radio Rom from the zip file and tried to upgrade both but on the the WM ROM was updated. The Radio rom still gives me an error when I try to Flash...
Ohhhh this is so dissapointing.....