ATT 8525 with a T-Mobile SIM - Wing, P4350 General

Hello All,
I recently got an ATT 8525 and I'm trying to use it with my T-Mobile (US) SIM. I was able to successfully unlock the SIM and CID with an util/rom I found on this site (I think the post was from Pof). And I also re-flashed the phone with the latest ROM available.
But after about 5-10mins of usage the signal dies and when I reboot it says No GSM. Looks like the Radio ROM gets corrupted. I tried just re-flashing the Radio ROM and that doesn't help either. It works for short while and again the signal dies.
And also, I'm unable to install any of the generic ROMs (Fantastic Mobiz, PVET 40005) Although I'm connected to Active Sync when I run the Step 1 (ROMUpdateUtility_NV_G3.exe), I get a ERROR [222] : DEVICE NOT RESPONDING. And when I run the step 2 directly (update_rom.bat) I get an cannot update itsutils.dll maybe in use error.
As you can tell I've been messing with phone a lot for a couple of days with no luck and my frustration level is kinda high
As of now here’s where I stand. I re-flashed the phone (Image: 3.62, Radio 1.50) and it’s on the “Tap the screen to set up your windows based mobile device” screen. I plan on leaving it on this screen until I can a good solution.
I would like to get rid of the ATT ROM and install one of those hybrid generic ROM that is not Carrier specific. Any help will be much appreciated. Share your ideas, I’m very experimental 
Phone Details…
ATT 8525
HERM100
IPL: 1.04
SPL: 1.40.0 lipro

Related

SX56 upgrade nightmare - help still needed

Okay, newbie upgrader here.
I've read a bunch in these forums, and it's been very helpful.
I upgraded my personal PPCPE (TMO) using their software, and it works great.
I was round my friend's house last night, and he has a PPCPE (AT&T).
Well, we downloaded the v30.09 firmware from Siemens website.
We backed up all the data.
We intalled the firmware.
At the end of the firmeware update, it said to turn the device off by using the hard reset button (that you have to unsccrew the stylus for.) and leave it off for a minute.
We did this.
It then said to turn it back on using the same reset button.
We did this.
However, we get the "Designed for Windows Mobile" logo, and the AT&T logo.
We get ROM versions:
G1.3.3
RA.33.02
A.30.09
After that nothing.
Having hastily given him my phone, I came home with his broken phone.
Well, having done a LOT of reading on this site, I got to use Jeff's tools to create a bootimage on an SD card, and I have been able to get the image flashed and loaded.
They device now boots.
However, I want to get the AT&T software on there as this is what's gonna make my buddy the most happy.
The image I have on there right now is SERv12.
Can somebody PLEASE tell me the best way to get this back to AT&T software running WM2003.
Thanks.
Okay, more info.
I have been successfully upgrading the ROM using the SD flash method.
I have been using Jeff's XDAtools to create the images.
I have been downloading ROM's from yorc and xdaweblink.
I have always tried versions without any software added to the ROM.
I have tried every version of 30.09 that I could get my hands on, even the one in the "SX56 upgrade utility" folder that the Siemens site created.
None have worked.
I have tried 4.00.05 ENG from yorc - didn't work (cool southpark screen though.)
I have tried 4.01.16 ENG from weblink - didn't work (Tmo verison)
I have tried 4.01.00 ENG beta from weblink - didn't work (Tmo beta version.)
I have tried A.30.07 ENG beta from weblink - didn't work (AT&T NFR version.)
I have tried 3.17.03 ENG O2-Euro from yorc -
When I say that the version don't work; here's what I mean.
I get the logo screen.
I get the three ROM versions in the bottom right.
The system then locks up and does not progress any further.
I have left the system on overnight with no difference.
The backlight comes on, but nothing else works.
I have tried the upgrades with and without a SIM card in place.
The phone was originally locked, but has subsequently been unlocked.
I have finally tried going back to A.20.17 from yorc - the original AT&T WM2002 version.
This version at least runs.
I still have the new radio stack running, but I am back to WM2002.
Does anyone have ANY idea how I might get this upgraded to WM2003.
My buddy want to run the MS Voice Command.
Also, with the updated Radio Stack, will he be able to connect continiously to the GPRS connection (sorry, I don't know too much about AT&T.) He really want the always-on internet.
Thanks for ANY advice given.
-=Nick=-
This happened to me using a mmc memory card to do the upgrade, it looked like it was doing everything ok, completed and gave the ok but on cold boot just hung, try another sd card, it just MIGHT work.
I'll look around for anohter SD card and see if that helps.
FYI, I've tried running the upgrade from the cradle/USB a couple of times, but that made no difference.
Also, since I was able to go back to WM2002 with the SD card, I can't see it being bad.
But thanks for the tip, I'll give it a go.
-=Nick=-

HELP WANTED - NO SIGNALS

I upgraded my pda with t mobile 4.01 beta rom then i was trying to get rid of it and upgrade to ATT latest rom. but it was not letting me to GET rid of it. SO i was trying many thing after doing them i saw that my pda`s phone feature is gone. then i installed RSU "PROGRAM B" SOURCEO2.com that is 4.0 something. I HAVE TRIED MANY THING BUT NO USE I HAVE ALSO DOWNGRADED TO WIN CD 2002
may be the att RSU will solve the problem. please tell me where to download it from.
the mobile was running on 900/1800
NOW THE PDA IS NOT DETECTING ANY SIGNALS.
AND I FEEL LIKE CRYING B/C IT WAS MY BROTHERS WHO GAVE IT TO ME FOR UPGRADING
Looks like you have the same Problem as i have. Check if your GSM-Module is still doing: You have to get into the Bootloader and check if it says "GSM OK" (then you are a lucky owner) or if it says "GSM Error" (then you´ve got the same problem as I´ve got). If it is the second case: Try this one: http://forum.xda-developers.com/viewtopic.php?t=1182&highlight=solved+gsm+error
Or this one: http://forum.xda-developers.com/viewtopic.php?t=4123&highlight=screen+1
But i need to say that these tips haven´t helped me out of this Prob. I hope it will help you!
So long...
no error any where GSM OK
NO HANGS every thing is fine.
Where can i down load ATT .20 RSU
I downloaded the rsu for ATT from yorch.net and now its getting signals.

Phone Function Dead?

Ive been having some problems off and on with my phone not getting any service. I would restart the phone and it would work for a while. But now I cannot get service anywhere and the phone seems to not work at all.
Has anyone else experienced this or are there any tricks to try and fix this. Any help would be greatly appreciated, as the device seems to be now useless. Thanks
Yep, same with me. I've just upgraded ROM to Faria's last version and still not working the dam phone func
My provider is Vodafone-PT, and i have a Dual Simcard. Even when the other sim is off (unregistered on the vdf network) my hermes simply doesn't register. Not even the emergency number calls are avaiable!!! However, all the other funcs are working fine.
I think it is a softw issue, but i'm still not getting to the point to solve this problem...hope some masters can help us.
regards
plenty of things you can try and troubleshoot with, hard reset, check for bad blocks, flash new radio/ROM.
As XtreMe_G said. I've been running Faias for the last week or two with no radio problems. HR problems, now thats another story. Mke me wanna go back to wm06.
...my problem now is WORST...i've tried to downgrade SPL to unlock CID and SIM, but for somehow the active sync crashed during the rom upgrade. Now i only see the tricolor screen, and active sync doesn't recognize my term!!!
The tri-color screen is bootloader mode and active sync will not recognize your device at this point. Start the ROM upgrade again and go through it. Sometimes the cooked ROMs might flash otherwise always, shipped roms are capable of being flashed from bootloader itslef.
Regards,
Carty..

Progressive phone problems

Man, I didn't even plan to have alliteration, and there it is!
So, I have had my cingular 8525 for about a year right now, and in the last 2 weeks or so I have been getting some bad problems popping up. For some background, I bought the phone in Texas and was using it on the cingular network for some time when they switched to the AT&T network. I flashed VP3G's AT&T roms using hardSPL and they worked well for some time. Then, I came to Europe to do a semseter abroad. I unlocked my phone using some software I found here on the forums (don't remember exactly what it was) and got an 02 SIM card. Everything went fine, was working well until I went on holiday to Europe. I didn't really use my phone much there because it was so expensive, but as soon as I got back I started to have problems.
For about a week, my phone would just drop in and out of service in places that it had not had any trouble working in before. What would happen is, in the place where there is normally the bars for reception, there would simply be an exclamation point and any time I would try to make a call it would fail, sometimes with a message, sometimes without. Then a couple of seconds later, I would have full service again, then it would go to the exclamation point again, full service, etc. It just kept cycling through them.
So, I came to my trusty forums here to try and figure out what was wrong. I flashed a different radio (from 1.47.30.10 to 1.48.0.0) which didn't fix it. I tried downgrading my SPL from hardSPL to 1.04, then upgrading back to the most recent hardSPL v7, which didn't work. I tried putting a new OS on it, the 19900 build, which didn't work. I tried switching the radio back, which didn't work. Then I started noticing that when I was starting up my phone, I was getting a 'no GSM' dialog where it used to say the radio version. I searched around the forums, finding some different solutions for the no GSM problem, and decided to try completly reflashing to an AT&T shipped rom.
So, I downloaded the ROM from the HTC site, downgraded my SPL to 1.04 again, and started the flash process. At 11% it stopped and had an error, and after that it wouldn't leave bootloader mode. I again searched the forum and tried to use MTTY to fix it. The command 'set 14 0' didn't work but 'set 16 0' did.
Now, my phone boots again, but it starts up with the AT&T screen, then goes into the 19900 build OS. As it stands now, I still keep dropping in and out of service, but I am afraid to try any more fixes for fear that I will screw something up again (like locking it in bootloader mode). Any ideas of the next step I should take to fix my (probably) corrupt radio?
OS: PDAVIET build 19900
Radio: 1.47.30.10
IPL: 1.03 (from failed AT&T flash)
SPL: 1.11 (from failed AT&T flash)
Update: I just soft reset my phone, and now the 'phone' feature of it won't even turn on when I select it in the comm manager!
Update update: As I was writing this, the phone just turned itself back on without me trying to in the comm manager. Maybe its just possessed, and I should seek the help of a priest!
1). Have you tried taking out the battery for a while? It seems that the hard reset is somewhat different from the soft reset and can fix this...
2). Check for bad blocks with MTTY... Remember though that sometimes the carriers put in "Bad Block" to brand the phone as theirs...
3). Try flashing a stock rom then reflashing wm6.1. This seems to help a hell of a lot of people fix the HR problem.
Hope these help you.... Cheers.

Trying SPV M3100 on Three UK

Hello all
As usuall we newbies tend to gravitate towards these great expert forums in hours of need. So any help would be greatly appreciated.
I'v been trying to get my old SPV M3100 to work with my new Three UK sim,
Iv run all the unlocking software and upgraded the ROM and radio with no error messages at all, yet everytime i try my Three UK sim in the SPV M3100 I get a SIMLOCK message and it greyed out so I can go no further.
My current setup is:
ROM Version 3.54.255.3
Radio Version 1.48.00.10
I wondering if it was the origonal unlocking that failed or weather the Three UK sim is just not working this phone.
Please excuse my ignorance, I've had a good root around the forum to see if anyone else has had this problem but I cant really find anything on it.
Cheers
have you tried this?
http://forum.xda-developers.com/showthread.php?t=293665
thats where I started, I ran the software from my SD card and then ran the herm-unlock v3 after windows restored.
The very fact you've mentioned that probo means I've done it wrong I'll have to try again, I know it didn't work straight off from the USB connection, so I'll try the usb route again.

Categories

Resources