Hello :
I have a Kjam :
Rom version: 2.16.9.1
Radio version: 02.07.10
ExtROM version: 2.16.9.101
I try do sync with my corporate exchange server 2003 sp2 using gprs and gives me a sync error - error 85010014.
Im using the same setings that my coolegues at work.
My user and pass are correct.
What can be wrong ?
Thnks a lot
Proxy?
I'd check to make sure that you aren't using a proxy. Go to start, settings, connections, set up my proxy server and make sure that you aren't using a proxy. If one is set up it may not be able to negotiate the login with your corporate exchange server... Just a thought.
Thnks..but im not using.
Luis,
Related
I've setup ActiveSync as dictated many times in the posts here and it doesn't complain one bit when syncing.
However, after a sync takes place (claiming success) there is no email in my message view for outlook mail.
Details: I'll even watch the sync take place stating 0/54 to 16/54 to 54/54, then a success message. Yet to no avail.
I've turned on Verbose logging, with no tell-tale messages shown.
Device Info:
ROM version: 1.8.10.2 WWE
ROM date: 12/10/05
Radio version 01.09.10
Protocol version: 4.0.13.20
ExtROM version: 1.8.10.104
Things doublechecked:
Exchange 2k3 - check
OWA login - check
GPRS connection - check
GPRS Inet access - check
Anyone seen this before?
Feel free to lambast me with what I've not done.
Thanks,
I just got a Wizard. I always get this error "Unable to obtain a server-assigned IP address. Try again later or enter an IP address in Network settings". Can anyone help, what causes this? Thanks
I have the same problem, especially when I am leaving BT ActiveSync connection. What kind of ROM are you using?
My Wizard has the following:
ROM version 1.3.13.5. ENU
Radio Version: 01.12.10
Protocol Version: 4.0.13.23
ExtROM Version: 1.3.13.116
Thanks
had the same problem
Yea, I had that same problem whenever i synced with my pc. but after i upgraded it to the new rom i've never seen it anymore. i dunno, probably a problem in activesync.
I am having all kinds of problems with my GPRS Connection. I have input the settings for Centennial Wireless, my carrier, and everytime I connect this is the message i get
dialed:
private.centennialwireless.com
Cannot connect for unkown reason. To check your connection settings and chem them if needed, tap settings. If teh problem continues, reset your mobile device according to your manufacturer's documentation and try again.
I did a Hard Reset and put the settings in again with the same problem. Any help will be greatly appreciate.
HTC Tytn
ROM: 1.18.255.3
ROM date: 07/22/06
Radio Version: 1.03.03.10
Protocol Version: 32.34.7010.01h
ExtRom Version: 1.18.255.106
Did you activate the hsdpa protocol ?
No I have not. Can you send a thread or tell me how to open that protocol? Is this done by the provider or on the handset itself?
Also how will this help if I can not even connect to GPRS/EDGE?
I have resolved planning in setting->connection->gprs setting
CHAP Autentication...
I am trying to setup a Wi-FI connection to the office network.
On the Laptop is it configured as WPA-TKIP with authentication using a 802.1x digital certificate..
I installed the certificate fine.
As soon as I try to connect to a network with it crashes.. Even after the restart, as soon as it tries to connect the system crashes.
I then tried new network defn:
Authentication: Open
Data Encryption: WEP
The key is automatically provided: checked
Use IEE 802.1x network access control : checked
EAP Type: Smart Card or Certificate --> with the correct cert selected.
This config also causes a crash. However, when it returns I am prompted to enter the user-id and can get connected. However, as soon as it comes out of locked state the system crashes..
The Rom version is: 2.20.707.1B WWE
Rom date: 13/06/07
Radio version: 02.93.90
Protocol version: 4.1.13.42
ExtROM version: Blue Touch ROM V4.0
Any ideas?
I've successfully upgraded my Qtek 9090 to WM6 Pro (5.2.16.20)
-
ROM version: 5.60.00 WWE
ROM date: 03/02/05
Radio version: 1.12.00
Protocol version: 1337.42
All works great, but still I can't connect to ActiveSync 4.5
When I put the Qtek 9090 on cradle it ask to install Activesync 4.5 or newer ... but I've installed (and reinstalled) this tool, downloaded directly from MS site.
I've also Updated all the components on PC (SO, Office, etc ..) with Microsoft Update. But still I've this problem.
Please, could you give me any help ?
Thanks in advance.
Beppe
-
i got the same problem!
my 9090 says:
cannot open the connection usb, this connection is no longer valid ore exist, plz select a diffrent
it worked until now
Sorry, my English is bad. But I try to help because I had the same problem.
Which firewall is installed?
With the change of WM2003 on WM6 new rules must be allocated for ActiveSync.
Several ports (999, 5678 etc.) must be switched free or turn the firewall off for testing!
Simply turning off the network monitor at the Comodo Firewall.
Good luck!
Mathias
My Qtek 9090 ask for Activesync 4.5 or newer while connecting.
I have just tried with another PC with XP on board and a fresh copy of Activesync 4.5 - Same problem (ask for 4.5 or newer)
I'm quite sure the problem is on PDA.
I hope in some suggestion.
Thanks to all.
Beppe
-
do search on the forum.. you'll find what you need..
cheers
evo
check\uncheck in USB to PC - Enable advanced network funkcionality try which one of them will work with your pc
RESOLVED !!! (Yeahhh)
The problem was on network properties of Qtek, when connected.
Right-click (in control-panel/network-connection) the Qtek entry / Then properties
- check only tcp/ip protocol and MS network services
- I've disabled bindings for VPN and packet-trace utility
Activesync 4.5 WORKS GREAT NOW
Have a nice WM6 upgrade.
Beppe
-