I just got a Wizard. I always get this error "Unable to obtain a server-assigned IP address. Try again later or enter an IP address in Network settings". Can anyone help, what causes this? Thanks
I have the same problem, especially when I am leaving BT ActiveSync connection. What kind of ROM are you using?
My Wizard has the following:
ROM version 1.3.13.5. ENU
Radio Version: 01.12.10
Protocol Version: 4.0.13.23
ExtROM Version: 1.3.13.116
Thanks
had the same problem
Yea, I had that same problem whenever i synced with my pc. but after i upgraded it to the new rom i've never seen it anymore. i dunno, probably a problem in activesync.
Related
I've setup ActiveSync as dictated many times in the posts here and it doesn't complain one bit when syncing.
However, after a sync takes place (claiming success) there is no email in my message view for outlook mail.
Details: I'll even watch the sync take place stating 0/54 to 16/54 to 54/54, then a success message. Yet to no avail.
I've turned on Verbose logging, with no tell-tale messages shown.
Device Info:
ROM version: 1.8.10.2 WWE
ROM date: 12/10/05
Radio version 01.09.10
Protocol version: 4.0.13.20
ExtROM version: 1.8.10.104
Things doublechecked:
Exchange 2k3 - check
OWA login - check
GPRS connection - check
GPRS Inet access - check
Anyone seen this before?
Feel free to lambast me with what I've not done.
Thanks,
Hello :
I have a Kjam :
Rom version: 2.16.9.1
Radio version: 02.07.10
ExtROM version: 2.16.9.101
I try do sync with my corporate exchange server 2003 sp2 using gprs and gives me a sync error - error 85010014.
Im using the same setings that my coolegues at work.
My user and pass are correct.
What can be wrong ?
Thnks a lot
Proxy?
I'd check to make sure that you aren't using a proxy. Go to start, settings, connections, set up my proxy server and make sure that you aren't using a proxy. If one is set up it may not be able to negotiate the login with your corporate exchange server... Just a thought.
Thnks..but im not using.
Luis,
I am having all kinds of problems with my GPRS Connection. I have input the settings for Centennial Wireless, my carrier, and everytime I connect this is the message i get
dialed:
private.centennialwireless.com
Cannot connect for unkown reason. To check your connection settings and chem them if needed, tap settings. If teh problem continues, reset your mobile device according to your manufacturer's documentation and try again.
I did a Hard Reset and put the settings in again with the same problem. Any help will be greatly appreciate.
HTC Tytn
ROM: 1.18.255.3
ROM date: 07/22/06
Radio Version: 1.03.03.10
Protocol Version: 32.34.7010.01h
ExtRom Version: 1.18.255.106
Did you activate the hsdpa protocol ?
No I have not. Can you send a thread or tell me how to open that protocol? Is this done by the provider or on the handset itself?
Also how will this help if I can not even connect to GPRS/EDGE?
I have resolved planning in setting->connection->gprs setting
CHAP Autentication...
Hi All,
We have a client who we supplied 2 TyTns the both have the same ROM:
ROM Version: 1.18.255.3
ROM date: 07/22/06
Radio version: 1.03.03.10
Protocol version 32.34.7010.01H
ExtROM version 1.18.255.106
One of them connects to Wi Fi no problem. The other says the network is available but when you go to connect the network key code is invalid. The key is identical on both devices.
Any Ideas? (apart from a hammer)
S
possibly both devices are using the same device name,try changingboth names to something different
Yes, or go to connections, network cards and delete the one in question and then have it re-detect the network and re-enter the key from scratch. i.e delete the card first not just re-enter the key in settings.
Mike
Hello, i searched about my problem but i couldn't found anything about it.
I updated to WM6.1 (WM6.1Pro v3.02 (sun_dream))
ROM version: 6.141WWE
Radio version: 1.15.00
Protocol version: 1337.45
If I want to connect to my WIFI, the BA said that the password must have 8 characters and were wrong. But my password ist longer than 10 characters and I got the right one. The encryption is WPA-PSK, or is only WEP with the BA possible ?
greetz lenha
you have to get in to settings/connections/network cards and in the connection of your hotspot ot what ever you use you have to click "edit" and there choose your settings.