I hope sombody can possibly help...I've just recieved my Jamin in the mail, and tried to turn it on...but it seems to get stuck in a blue screen that has the i-mate logo, and the system info in the top left corner. I've tried several soft resets, and tried to hard reset to no avail.
Is there anyway to get around this? Or is my brand new toy already broken.
Thanks in advance for any suggestions or help.
When you said hard reset, do you mean you DID hard reset it but you still facing the same problem, or you are not able to perform hardreset at all?
I did a hard reset, and that put me at a screen with three color bars running across, Green, Red, and blue. At that point I was stuck again...had to soft reset to get ot of that screen.
Thanks!
get it to the blue/red/greem screen again and flash it to the latest Imate Rom.
I can get it to the tri color screen, but my PC won't recognize it, so I am unable to flash it with the latest ROM. Any suggestions?
Found the problem!!
I was hitting the wrong buttons for the hard reset. Hit the Comm mgr, camera, and soft reset buttons, then hit send when prompted. It returns to the boot screen, and after several minutes, will finally start up.
Thanks for the help!!
Related
I just installed this program, used default settings, apllied, My 8125 soft reset.
Now I cannot see anthing past the initial screen that lists IPL and SPL version.
Just a plain white screen, Active sync wont work, no buttons work. Please help !!!!!!!!!!
If you're stuck I think the only next step would be a hard reset which is going to drop it back to the base factory build so you'll lose anything you've installed etc.
How do I hard reset 8125, with buttons only (key / button combination) OS does not boot or visible.
press the "connetions" button (on the left hand side of the unit next to volume up/down) with the "voice" button (right hand side of the unit opposite the connections button) and then use the stylus to do the normal soft reset and it should hard reset back to factory settings - it's described in the manual
Tried hard reset several times, no luck.
All I did was installed registry wizard from here
http://forum.xda-developers.com/viewtopic.php?t=39725&highlight=registrywizard
and now I can't get it to do anything, anymore suggestions ?, your help is really appriciated, I have only had the phone to 2 days and its dead already
try holding the same two buttons and then hitting the power button instead of the reset thingy... this method was easier for me... If this dosen't work you will have to enter bootloader mode and reflash the rom.
For the detailed reset procedures try here
By the way, did you use that program to change the default input method?? I use it all the time and the only time it gave me the whitescreen is when I tried to change the default input...Oops. I believe that you should be able to use that program safely, just leave the default input alone... Hope this helps.
Thanks for info, I did manage to reload the ROM. and Yes I did change the default input method, that might have done it. Thanks all, for your Help.
raheelb did you have the warning that the proggie cannot recognize the AKU version?
I had had such a warning, unfortunately bypassed it and had the same issue (white screen) - any one knows why the RegistryWizard cannot recognize AKU version? I have the original Qtek 2.17 ROM installed... :?
Hi,
Recently my pda(k-jam) fell from my pocket and it hanged. I did a soft reset but I get this error message "Press Send to restore factory defaults, Other keys to quit"
I tried all keys but in vain. I then did a hard reset by pressing the comm and the voice dial. (did a reset with my stylus). I still get the above error message.
Does anyone have any suggestion or idea how to reset my pda?
Thanks alot.....
Y dnt u flash it with a new Rom look around the forum for the new MOSKI ROM.
Thanks
Thank you for your suggestion, I will think of upgrading to molski.
But will it upgrade ? As a hard reset also doesnt seem to work and how do I get to reach the ROM if I am not able to see the other things?
Thanks
Please help...
Hi ,
I am a newbie and so would seek alot of help. Thanks in advance...
Couple of days back my pda fell and now after soft or hard reset the screen still shows this "press send to restore to factory defaults, other keys to quit"
I would like to upgrade to molski but they say I might have to downgrade my rom but I must first unlock the device. There are g3 or g4 device..how do I know what device my k-jam is...g3 or g4? How do I follow up or know?
Could anybody give me the link or solve my problem? As my k-jam just wont pass that screen..I tried looking into various topics but couldnt go about the first step I should be taking...
Please help!
Thanks
Hi,
Please help..after hard reset, it still does not happen to load into the factory defaults... I cant flash my ROM or anything ...as it wont progress further than that screen ... "Press Send to load factory defaults, or quit"
Anyone have any suggestion?
Hold down the camera button while resetting it. If you can get it to the bootloader (three color screen), you might be able to flash it with something and possibly rescue it. It does, however, sound like you might be screwed. Things break when you drop them, including plastic phones.
hi
Thanks but if I have to do a hard reset, I would already be holding the comm manager and the voice dial with the stylus to reset. Do I hold all the 3 buttons together while hard resetting ?
I have tried all the buttons after doing the hard reset but just doesnt get to the other screen.
Thanks for your help.
Hold down the camera button, Power Button and Pin in the hole. First relese the hole, then release the power button and keep holding the Camera button dis will bring the Tri-colour screen. There'll be some info. like IPL n SPL der
If IPL n SPL are like:
IPL 2.xx.xxxx or 1.xx.xxxx
SPL 2.xx.xxx or 1.xx.xxxx then ur device is G4.
if its like:
IPL 2.xx or 1.xx
SPL 2.xx or 1.xx then ur device is G3
if its G4 you need to CID Unlock that before upgrading it.
All the LUCK. Go Ahead.
Hi
Thanks,
I tried your steps but it still wouldnt work. But somehow I did the switch below the comm button and it showed me the screen to the somethign HTC innovation or like that.
I think I had to tinker with the switch below the button to get the screen working.Thanks for your help.
Hi XDAers,
I have tried a number of things and is at a loss - I have a 2 years IMAT KJAM Wizard G4. The problem occured 2 days ago when the device just freezed on me. I did a soft reset, booted fine but then came up after the initial load screen (WizardLove AKU 2) with a white screen.
I have reloaded the IPL, flashed the ROM with WizardLove again, Hard reset back to factory defaults, soft resets the works.
After ROM flash it boots up, i get ActiveSync to load and connect fine. but with in 5 - 10 after having the phone up and working the screen goes white.
If any one has any idea what could up with the Wizard device please let me know?
Regards,
Hennie
I have the same problem!
Not sure how hard it is to fix but it seems to be a component issue,
Iknow its a different phone but check out:
http://forum.xda-developers.com/showthread.php?t=303872
I havent tried it yet but it worked for them
I recently flashed my opal to wm 6.5 and it worked perfectly fine. Yet today when I tried to install a software which would help display chinese character, after reboot, it got stuck in the smart mobility screen. I have tried hard reset and it didnt work. HELP ME!!!
you can still hard reset it in that state... do the usual hard reset, press both green and red buttons at the same time and with the stylus press the reset button at the back and release it. don't release the green and red buttons yet, release it when you see the instruction "This operation will delete all your personal data blah blah"... then just follow the on-screen instructions.
If TheRem's solution doesn't work you can reset the phone while holding down the Volume down key and it will take you to the SPL (tri color screen). from there you can plug in your phone to USB and flash PhamQuangs ROM again.
Double Post
Closed.
Dave
Just loaded another keyboard cab and suddenly on soft reset/reboot the phone has frozen at the HTC logo and the screen showing the RGD info... won't reboot easily and takes many attempts to get back to this screen.. but will go no further.
So to do a search, what keywords should I be using or does anyone recognise this and have an answer.. have tried reset, battery out but nothing is working, the screen is just locked the screen mention above.
Using Laurentius26 GoldEdition V2.1 rom and was loading Touch-Keypad.Cab..
It is not connecting to the pc, so I can't reflash it at this time..
if you're phone wont boot since you installed this then looks like a hard reset is on the way mate sorry, you could try boot without mem card but doubt that will make a difference
Could you quickly remind me of the sequence for hard reset, red reset button doesn't seem to do a lot and I do have everything backed up so its not a problem... cheers.
press and hold both volume buttons and tap the power button. Keeping holding both volume buttons until it asks you if you want to factory reset the device. When it does tap volume up and it will then go off and do it's thing.
if the crash was the first time you had soft reset since youi installed the cooked rom, (even if you had been using it a while) it could be a mismatched radio. (Sometimes the rom/radio mismatch doesnt show till the first restart.)
Look at the R on the boot screen, if it has .51. in the version, then flash a new radio.
Thanks for all the help.. have managed to recover, restart and reflash, then reload, so we are all sweet now.. cheers..