PC/Laptop to xda 2 viewing - MDA II, XDA II, 2060 General

Hi,
could an expert out there advise me if my theory is possible please?
Using Remote desktop/Terminal services : See whats on my PC/Laptop on the screen of my XDA2 - connected via cradle and usb(as usual). If so what do I put in the "Server" box of the XDA Terminal services prog and on the "Main" PC.. Do I have to make a Network first? Or ?
Thanks to all.
The site is great but much of it goes straight over my head at the moment..
P

ummm ... your theory seems not that much difficult as you can implement it using Bluetooth networking I guess ..
you can setup bluetooth networking from Pocket PC to Laptop then you can browse what your home PC conatin from your PDA
give it a try
I hope this is what U was talking about , if not please give us more clarifications
Cheers

It is better and faster to use Wifi if you're going to use terminal services.
Been using this method since last year.

Thanks but I do not have wifi or bluetooth...
There is a ref to doing it on MS site via the cradle and usb but then it shoots off in the over the web stuff...
I have tried just now but nothing connects.... But I notice that when I check my desktop (xp) pc under the rempte tab - I only have Remote Assistance.... Could this be it? Perhaps I do not have Remote Desktop installed then ! Eh? I will try to locate my original xp discs and see if I can install !!??
Ta.

Remote desktop or Terminal services connect only via IP address.
So you can only connect via TCP/IP using WIFI on your XDA.
Bluetooth 1.1 has no IP address setting so it is not possible also.
I tried all methods since last year and WIFI is the only solution or if your XDA has a backpack you can use a CF type NIC for wired connection via crosslink or hub.
Still Wifi is the cheapest and cleanest alternative. You can use Adhoc settings between your PC if you have no WIFI access point.

Related

Widcom stack bonus! Wireless Networking(OT- not GPS related)

Hi all,
I've been following the Widcom port across to the XDA-II, not because I want to attach a GPS, but because of the much expanded feature set.
I installed the BluetoothGPS.zip file, then activated all the new services offered by the phone.
I have a Belkin F8T001 USB Adapter in my broadband PC. I want to use BT to surf the net from the XDA without paying O2. Trouble is, my Belkin doesn't provide an Activesync Profile, so it can't be done. Until now, that is.
Belkin USB adapters offer a 'Network Access' service. The Widcom stack now allows the XDA to wireless network with my PC, map drives with Resco Explorer, surf the net without the bother of Activesync, oh, and Activesync over BT Wireless LAN if you like. The PC acts very much like a WiFi access point.
Another excellent bonus is the ability to browse the PDA with the BT 'File Transfer' Service. This is easier than browsing through Activesync, as you can open picture files directly without having to transfer them to the PC first.
Nice one guys, well done!
Steve Head
And where can I download these drivers ?
Sounds like a solution. Where???? :lol:
Here:
ftp://dgmatic.com/XDA2/BluetoothGPS/
Login: xda
Pass: xda
is there a current url for an up to date version of the widcomm stack which can be directly installed?
PAN vs LAP Bluetooth Profile on XDA / iMate
G'day All,
Thanks for the post on Net access - It's not as easy as it looks (having spent AGES getting iPAQs working with Bluetooth Dongles (BTW: You DO need 1.3.2.7 of the Widcomm Stack on XP to make PAN connections work!!!
My question is:
Has anyone managed to work out how to get PAN or LAP Network Bluetooth access going on an XDA II??
I can easily get a PAN network access connection going on an iPAQ 5550 (with the identical Widcomm stack version) - On the XDA II with the Widcomm stack installed, it defaults to a LAP profile... (Using BT Null Modem). I can't get this method working with internet access.
If I connect XP to the iMate, then the PAN driver is used on the PDA - BUT I can't get any traffic through (this is the same on the iPaq and the iMate).
Anyone got any clues / hints for me, please?!?! (ROM versions etc are latest).
Cheers.
Andrew
Re: PAN vs LAP Bluetooth Profile on XDA / iMate
acurtis007 said:
G'day All,
If I connect XP to the iMate, then the PAN driver is used on the PDA - BUT I can't get any traffic through (this is the same on the iPaq and the iMate).
Anyone got any clues / hints for me, please?!?! (ROM versions etc are latest).
Cheers.
Andrew
Click to expand...
Click to collapse
Hi,
I'd same the problem, but since I enabled service Personal Network Sever, then at PC side connect to Xda II, it's working, I can ping from / to Xda II.
(enable service by start > setting > bluetooth > from File Transfer to Personal Network Server, I checked them all)
But it's problem to connect via Xda II to PC, then I restarted PC and PPC and make new shortcut of PC Network Access.
Now it's working I can use Resco file explorer to map driver of PC share folder and get access to file. But it's seem unstable because it's hang sometime.
ps: Thank so much to the great person who made bluetoothgps.zip.
cairo31male said:
Here:
ftp://dgmatic.com/XDA2/BluetoothGPS/
Login: xda
Pass: xda
Click to expand...
Click to collapse
I could not login. Thanks anyway.
bluetooth zip file not available anymore
I tried the url, but is is not responding anymore with ftp and the username and password. Has anyone it for me??
I'd very much like to get hold of this file as well, same problem - user/pass doesn't work anymore.
Probably don't need another "me too" but I have been searching for this stack high and low! Please let us know where we can get it!
Immense thanks!
I have BluetoothGPS.zip (about 2Megs zipped) give me somewhere to upload it & i will.
That's a shame, it used to be on ftp://hydrosphere:[email protected]/ but it's gone now. I've obviously got it, but I'm damned if I'm hosting it as it's 'unlicenced software'.
Any suggestions?
As acurtis007 pointed out, it's not easy to do this even on the correct PDA. If you do get hold of the Widcom stack, you need to understand networking and a little voodoo to surf the net.
One advantage is that the BT Dongle in your PC becomes like an access point. You no longer have to set up an Activesync Partnership, so a PC can be logged in as anybody, and any PDA(s) can surf.
Here's the way to get Surfing over BT using proper IP NAT:
Your XP PC
Your installed BT Dongle should offer a Local Service called 'Network Access'. This should be started automatically, and creates a 'Bluetooth LAN Access Server' interface in your Network Connections. This is the important bit: Activate 'Internet Connection Sharing' on your LAN Card. Select the Bluetooth LAN Adapter as the Interface you want to share with. If you don't have a LAN card, then share whatever interface connects to the Internet.
If your LAN Card already has an ip address that starts with 192.168.0. then you're out of luck. You'll have to change the entire setup of your LAN to another Subnet. I chose 192.168.50.x, which is fine.
If you have correctly activated ICS, your BT LAN Interface will have the IP address 192.168.0.1, and your Internet device will have a hand under it's Icon.
You're XP PC is now ready to accept Bluetooth surfers - both of the Internet and your LAN.
The XDA-II
Bung in the Widcom Stack
Run the Lovely new Bluetooth Connection Wizard and Explore. You'll see a PC icon appear, tap it. You should be offered a range of services, depending on what make of BT Dongle you have. Select 'Network Access'. A Shortcut appears. Hold the stylus down on the Icon, and select Connect from the pop-up. You will have to do the PIN thing as you connect the 2 devices. The XDA's Bluetooth Null Modem then connects to the PC, and hello broadband.
The stack is very stable. I've been using it for 2 weeks now every day for both surfing and file transfers.
It's not perfect - beware
This is a hack, and therefore does not operate entirely correctly:
You will ALWAYS get an error message when first initialising the new stack. I'm used to it: Start Bluetooth - it fails; Start Bluetooth again - it runs. This happens every time, and I just live with it. Once it's up, I can surf till the battery dies.
You will need to reset your XDA-II's Connection Settings (Advanced - Select Networks) back to 'My ISP' where it says 'Programs that....Internet..'
Others on this forum have reported that the XDA's sound gets disabled when you uninstall the Widcom cab file. I haven't had cause to do this as I'm 100% keeping it. This is the advice I've seen posted:
"Uninstalling Widcom Stack
If you have the Widcom stack go to the WIDCOM BT-manager Audio gateway tab and Disable this before uninstalling. Sound should then remain actve."
So there you go - it works a treat.
Steve Head
If you want a bit of fun, try this:
Get yer Widcom network access up 'n' running
Put a TV Tuner Card into the PC with the BT Dongle attached, and hook up your Sky Box to the TV Card.
Download the free 'Microsoft Media Encoder'
Using Media Encoder, Run a Live Broadcast, and select 'Pocket PC Widescreen' as the target audience. Your Sky Box output (or whatever) is now being converted into a TCP/IP Stream at the sort of data rate your XDA can handle.
To watch Sky on your XDA all round the house, run Media Player on your XDA and enter the url http://192.168.0.1:80 (assuming you're connected via BT). You can also do this with a Webcam, and remotely monitor it full screen on your PDA.
Steve Head
sorry i forgot i could just attached it
Enjoy
It works
@ArcticCat
Thank you! (I nearly was loosing hope!)
1000 kisses, beers or whatever...
Pauline
Thanks I could kiss you all.
now for the winge.
As the XDA connects to the LAN over a BT null modem. It seems to be quite slow.
Is this due to the settings of the modem restricted to 11500 baud rate limit for the hardware?
Whilst i am at it. let me throw this in the works.
The XDAII connects via BT to a PC on the network. I can browse the network from the PC. But i can only browse the files on the PC that i am directly connected to via BT from the XDA as well as access the internet. Is this normal?
IP address is 192.168.0.1 on BT adapter. The LAN connection of the PC is 192.168.11.5 ( auto ip).
all other PCs on the network are in the 192.168.11.x range.
Any suggestions?
Cheers
Oorbz
As the XDA connects to the LAN over a BT null modem. It seems to be quite slow.
Is this due to the settings of the modem restricted to 11500 baud rate limit for the hardware?
Click to expand...
Click to collapse
I found out that the speed networking over BT is slower than expected. Any others having problems for repaly MP3s on their XDA. I think the max speed over BT is 1MBit. Whith all protocol things you schould get min 500kBit. But I have problems playing MP3s with mor than 192kBit, The XDE "feels" very slow. - any ideas?
But i can only browse the files on the PC that i am directly connected to via BT from the XDA as well as access the internet.
Click to expand...
Click to collapse
Oorbz: To conect to your home LAN you need to set up a Networking bridge (Because your network is devided in 2 segments). Using windows xp its included. Mark both network adapter and choose "Network bridge". After that you only configure the bridge and both networks are conected under one subnet mask. Sometimes BT-Adapters are not fully compatible with the network bridge. Then you need to do 2 little steps:
On the console type in:
Code:
netsh bridge show adapter
then type in
Code:
netsh bridge set adapter # forcecompatmode=enable
# stands for the Number of your BT Adapter.
Thats it. Now you have access to your complete LAN and NAT-Router. Using a fix IP on your XDA will speed up the start of the conection, but DHCP works fine too. All computers whould now have an IP from the same subnet liek 192.168.0.# / 255.255.255.0.
PS using a WLAN adapter some drivers need this settings too in order to work with the windows XP networking bridge.
On the console type in:
Code:
netsh bridge show adapter
then type in
Code:
netsh bridge set adapter # forcecompatmode=enable
# stands for the Number of your BT Adapter.
Thats it. Now you have access to your complete LAN and NAT-Router. Using a fix IP on your XDA will speed up the start of the conection, but DHCP works fine too. All computers whould now have an IP from the same subnet liek 192.168.0.# / 255.255.255.0.
PS using a WLAN adapter some drivers need this settings too in order to work with the windows XP networking bridge.
Click to expand...
Click to collapse
I tried the network bridge a few days ago with the card in compatiblity mode. but i will give it another go . I will repor back. Thanks
Hi
You mentioned the Belkin BT adaptor. That is about 30 odd pounds. Are all BT adaptors the same? i.e. do they just implement some version of the protocol? Seems the Belkin one implements v1.1.
How about this one, will it also do the job?
http://www.qtds.com/code/products.asp?recid=621&
Costs about 15 pounds, so much cheaper
btw, if your laptop already has BT built in, do you need to buy a dongle?

XDAII Browse Network Neighbourhood ?

Hi All,
I don't yet own an XDA but am looking to buy an XDAII in the next couple of days. I have a question, for which I have tried searching for the answer but to no avail which is. Is it possible, using an XDAII to connect to a LAN via a machine with a USB BlueTooth adapter and browse other LAN connected machines. In a similar way to clicking on Network Neighbourhood from an normal LAN attached PC viewing other PC's shares ?
Any help appreciated.
Thanks,
Rob.
Hiya,
I'm also interested in finding this out, is there anyone who knows the solution?
Regards,
Chris
I don't know about performing it over Bluetooth, but it is certainly possible to do it with Wi-Fi using a program called Pocket LAN. In fact, I connected from the car park to my local B & Q store and was able to see all their PCs and printers connected to their network using that method. I was tempted to try and send something to one of their printers, but thought better of it. As to bluetooth, I guess it should be possible providing the machine your trying to connect to is routing IP requests onto its LAN.
Tell us where that B&Q was
I couldn't find Pocket Lan through Google?
Do you know where I could get it? I'll happilyb trade you a beta fo Pocket WiNc for it? :wink:
Found this link ....
http://www.pocketpclife.co.uk/featureddetails.asp?article=419
But also need to know where to buy/download
here's the linkk
http://www.regnow.com/softsell/nph-softsell.cgi?item=6752-1&affiliate=16663
alternatively, google= z2 pocket lan

"how to" view internet pages using bluetooth

Thanks to the last chap who told me to use activesync to view web pages using bluetooth.. the problem is "How" to get it to do that.. I have a little bluetooth dongle on the pc but they don't seem to talk to each other even though they are bonded.. and precisely how do i view an internet page using bluetooth
Do you tyhink it may be a bluetooth compatiblilty issue.. I've heard that maybe a different dongle and driver may do the trick?
The Idiot's guide would be much appreciated!!!
Gumby
Hi,
I downloaded the Bluetooth application ("fix") from here:
http://bluetooth.i-networx.de/index_e.html
Then Bluetooth works perfectly with my 3com PCMCIA card in the laptop.
I now only do ActiveSync via Bluetooth with one exception - when I want to send music via Windows Media to the Imate I have to use the cradle or cable because the bluetooth appears to the laptop as a serial link and the Windows Media does not support serial devices.
I can also use internet on the Imate via ActiveSync and bluetooth - although generally I stick to the laptop for that !
Regards, Dave
Thanks but unfortunately the fix doesn't bring up a web page anymore.. what is it that your suggested fix is fixing? AArrghhh! Can someone please come to the house and sort it out!!!!!!!!!!!
Thanks but unfortunately the fix doesn't bring up a web page anymore.. what is it that your suggested fix is fixing? AArrghhh! Can someone please come to the house and sort it out!!!!!!!!!!!
Hi again,
This bluetooth fix allows a simple connection from PC to Imate via ActiveSync and Bluetooth. It does not address internet issues.
Have you tried connecting the Imate/XDA2 to a PC with cable or cradle and then used Internet ?
It could be that your problem is not with Bluetooth - have you tried the Connection settings ? or, have you check the ActiveSync settings on the Imate.
Rgds, Dave
I probably understood your problem. You can't connect your Xda via ActiveSync via bluetooth.
First..assure the 2 Bluetooth devices are on discoverable mode.
Then go into your Pocket Pc START-Settings-System-Blueooth settings-tap to Bluetooth ActyveSync setup[start]
Select Discoverable mode and Tap in Bonded devices and NEW..
So..wait and Select your pc.
Then you will pair your pc with Pda.
Inserted the same code on 2 devices you probably can connect to ActiveSync via bluetooth.
Simply go in your Pocket pc,START-ActiveSync-Tools-Connect via bluetooth.
If this not help,try to set the right port on your PC ActiveSync-File-Connection Settings-COM1-2...etc..
Contact me if problems seems unsolved
[email protected]
Regards,
Ser

Please help, I am struggling to network my xda iis

I've been trying to setup a network between my XDA iis and my desktop PC. I want to be able to access the internet connection which my pc has on broadband, and to access the pc's files and printer. Also to access the xda files from the pc via shared folders etc.
My setup is a bluetooth usb adaptor pluggedinto the pc with belkin software installed. The xda has BT already on it.
I have no idea how to go about now etting up the connection between them. I think what I need is a VPN but I'm not sure.
Please can anyone talk me through the setup, it's driving me mad to a point of disliking the xda?
Bluetooth can be a pain, and not particularly fast compared to wifi.
Synopsis:
You don't need to use VPN, just a standard bluetooth serial port (eg Com 6), use PC's activesync to connect through eg Com6 and set your PDA to activesync through bluetooth.
http://forum.xda-developers.com/viewtopic.php?t=26479&highlight=bluetooth
V
Well i originally had a wifi card on the advice of a pc store, and was told I could set it up peer to peer without a router. This was a complete failure and in the end they swapped it for BT card instead. Is it going to be easier and more reliable to setup a router for wifi rather than peer to peer?
you can only get data over bluetooth with the ms stack if you are connected to activesync using bluetooth
http://www.geekzone.co.nz/content.asp?contentid=2417
http://www.geekzone.co.nz/content.asp?contentid=3163
the problem is tha it dont support the PEN profile
of cause if your bluetooth stack is vidcomm or broadcom then look here
http://wiki.xda-developers.com/index.php?pagename=InternetOverBluetoothNetwork

It's possible UMTS+ActiveSync?

It is possible connect to UMTS/GPRS while Activesync is on?
The idea is to access from a portable pc without internet connection and use the feature with Pocket Controller Program and ONLY in JASJAR, without use modem feature or PC explorer or another, only Pocket Controller and soft on JASJAR.
Thanks
Well I know I can use the wireless modem over bluetooth whilst I am stil connected for activesync over USB to my PC
Yes, I know about modem usb or BT...
My question is another. Is for use like I described in my post.
Thanks
Ahh Sorry - I think I understand the question now. You want to use your JASJAR to surf the internet through SOTI pocket controller whilst it is still hooked up to your PC with ActiveSync.
Can't see why you would want to do this, but I'll see if I can figure it out.
Exactly, that is!
Thanks
I tried this also, but failed.
Exactly, fail. So I ask for it.
Thanks
In order to acheive this you must disable the "pass through" connection that active sync makes when it connects. I'm not sure whether this can be done
Hummm I cannot see that option... I't possible that register must be modified but.... how!? That the question.
Thanks
Sagit said:
It is possible connect to UMTS/GPRS while Activesync is on?
The idea is to access from a portable pc without internet connection and use the feature with Pocket Controller Program and ONLY in JASJAR, without use modem feature or PC explorer or another, only Pocket Controller and soft on JASJAR.
Thanks
Click to expand...
Click to collapse
If you just want to see your PPC on your PC using Soti's Pocket Controller, you can setup a TCP/IP connection in Pocket Controller on your PC given that you have a Wireless network setup. Using this method does not require that you have Activesync running and will be able to use UMTS connection at the same time... I've set this up on my PPC and network.

Resources