Hi All,
Just wondering if anyone else is getting intermittent issues w/ their mini-SD card.
I've lost essentially all my data on my 2GB Sandisk on three separate occasions. I have formatted different ways (once w/ RescoExp, and then FAT32 on 2 computers), been v. careful closing my apps and minimizing the amount of writing to the card.
Does anyone have any suggestions?
Sandisk's comments are as follows:
"This is a known issue with the devices when they work this way with 2GB and up memory cards. Usually in this cases you just need to contact the manufacturer of the device that you having issues with the reading on, to find out about compatability and what kind of firmware update do you need."
Thanks!
I haven't had any issues with my SanDisk 2gb card using my K-JAM.
Now on other pdas and with other cards, I have had the "lose everything" problem. Two reasons I had...storing email attachments on the and having the unit crash while accessing the card.
My onyl problem with the larger card is my laptop doesn't recognize it
I lost all of my data just last week off of my card, I went ahead ahd reformatted it again, not sure whats wrong with the 2gb cards
m2nal said:
I lost all of my data just last week off of my card, I went ahead ahd reformatted it again, not sure whats wrong with the 2gb cards
Click to expand...
Click to collapse
I haven't had a single issue with my 2GB TOPRAM card. I have had a few issues where the device doesn't see it (I assume) and renames the folder to Storage Card 2 and creates a new folder "STorage Card" with nothing there. It happens rarely and when it does, I just take the card out, rename the bad folder to StorageCardOld then insert the card again. This corrects the issue. I use the card very heavily and have had it since around the end of January.
I too have had this problem. I hope my suggestion helps.
I've had issues in the past with Sandisk flash cards. My problems were the same as yours until some helpful spark suggested I do a disk error check using windows (right click on drive in explorer>properties>Tools>Error Checking). Format the card and then run the disk check, apparently some Sandisk flash cards exhibit not so rare sector problems. His explanation (the science bit of which I have long since forgotten) was that that by running the disk check, the utility automatically marks the error causing sectors as unusable. The disk can then be used as normal after that, but any reformatting should have the disk check run again to mark the sectors once more.
This has helped me in 2 out of three occasions and so may or may not work for you. Still, I hope this solves your problem.
BS answer from Sandisk
Leighj, that's a BS answer from Sandisk. I guess it would never occur to them that your SD card is defective. Try another card in your machine or that card in another PDA phone if you have either of those options, but if not contact Sandisk and get a replacement. It should have a lifetime warranty, or at least several years.
Have to agree with iclick. My Sandisk cards were basically defective and how I got them running was a workaround and not a solution.
Yes - I wasn't too happy with their response either. Anyway, I just ran through error checking before & after reformatting. Hopefully that works - if not I'm off to shop for a new card. Either way, it's probably the last Sandisk mem card I purchase.
Thanks for your comments!
I have a Sandisk 2Gb Mini-SD as well and I've not had any issues with it so far. If it helps, I've left the card in the factory default format of FAT only - not FAT32. Try putting yours back to FAT and see if you still get any issues. Depending on what program you use the option you want might be labelled as FAT16 instead of just FAT.
I have Sandisk Ultra 2G miniSD, I don't have any problems untill recently. Whenever I try to add my storage capacity to more than 60%, 1GB or more, it gave me an error because the file is write protected and then not responding file transfer.
First, I taught my file is broken, but when I removed other files from the mini SD card and then add it ..... it's work. I used a factory Format type. Do anyone have this problems :?:
Well after contacted Sandisk customer services regarding my memory. They asked me to reformat my card and I did that. through my laptop, but it said that windows cannot complete the format. Now the card is dead. :twisted:
Do the mini sd cards have a lock?
Do these cards have a lock on them? My old SD cards had a slider but I don't see one on the sandisk card.
The miniSD doesn't have a lock, but the miniSD-to-SD adapter does have a slider just like a real SD.
if i take my sd out for any reason it will often take a few goes to get it recognised by the mini s again. I have to remove/insert it as many as 10 times.
I'm on my 2nd card now, different brands, different speeds, and my card gets corrupted almost once a month. I make weekly backups of the card, so I never really lose data, but it's a pain nonetheless.
The symptoms are same each time. When it happens, I can browse the SD card with no problems. However, it won't boot with the SD card in the slot. I must first remove it, boot up, then I can insert it. Activesync does not work with the card inserted, and the Messaging app won't even open, so I have to remove the card before I can sync w/ my Exchange Server.
I'm not sure why the Messaging app is so tightly integrated with the SD card and why the card would prevent the app from opening when the card is in the slot. The database exists in the internal storage; only the attachments are stored on the card.
Anyone else experience this craziness?
What brand are your memory cards and where are you buying them?
Ok, so i bought a miniSD card for my Cingular 8125. Its a 2gb card. At first it was having problems reading things from it via the phone so i used the WM5torage application to format it and now its only reading as a 1gb card. WTH? what can i do to format this card again and get my lost gig back?
it just splits it to two cards (i.e c: and d: on the pc). you can switch them with the wm5torage...
I've had a T-mobile MDA (USA) for about a month now, and I really enjoy it! But, starting a few days ago, I've been having a lot of trouble with the MiniSD flash memory cards. The first card I had was a Corsair 2GB minisd, it worked fine for about a month, then it mysteriously stopped working a few days ago. I decided to RMA the card, but while I waited for my new one to arrive, I would purchase a cheap 1GB minisd so I could at least have some of my data and programs.
The second miniSd (this one branded with the name of the store I got it from: 'Micro Center') lasted for the past two days. I noticed it was dead this morning.
Here are the symptoms in both cases:
-SD card disappears from device.
-Soft-reset / Hard-reset to find that device wants to format SD card b/c it is unreadable.
-Format SD card, only to find that it disappears from the device once more
-MDA no longer responds to SD card.
For Corsair 2GB MiniSD:
-Attempt to format SD card using desktop PC, which leaves the card with half of it's total memory available (1GB). This is also not readable on the MDA device.
I'm very distraught by this whole incident - is it possible that there is something wrong with my MDA? Or is there a possibility that the programs and data I'm storing on the MiniSD are somehow corrupting it?
There's a T-mobile store near my office, I'm thinking about heading over there on my break to ask about this... but I'm afraid I wont get anywhere with them...
If anyone has any thoughts, suggestions, etc... please let me know!
Thanks
I have issues with my SD card. Quite infrequently the SD card disapears - which is pretty annoying. In my case simply ejecting it and reseating it seems to fix the problem. Occaisonally it becomes a little more problematic.
I think it is a problem with the SD socket on the Wizard, as a friend of mine has the same problem.
I have a 1 gig card in my phone and have just bought a 2 gig card.
I want to simply transfer all the data from the 1 gig card to the 2 gig card but dont have a card reader
I have tried to drag the memory card file to the desktop but all i end up with is a raster file.
Surely this must be possible.
Kind regards
Jon