during a modernization it has broken the connector of my 2020 in irreparabile way pda hour and in state of boot and I do not succeed to carry it in normal mode someone can help me?
Related
Hi all. I'm a little desperate. Following an attempted upgrade to Radio 1.06.00 I'm left with an Exec which is stuck in Bootloader mode, won't sync and wont flash from the O2 website flash installer.
Does anyone have any ideas? It's in warranty and insured.
Heeeeeelp
Try applying the 1.06 update again. Mine got "stuck" the first time, and I had that cold panic shiver of "oh god, what have I done", but it will go through the second time, I'm sure.
Cheers,
Steve.
Dear kinkybookworm,
Please unplug the usb cable.Deattach sim card and sd/mmc card and soft reset the unit.After you see " SERIAL " on the screen, plug the usb cable and reflash the unit with radio upgrade again.i guess that this will solve your problem...
Regards and thanks...
Hi every body!
I have a Qtek s200, but when i tried to upgrade its Rom, unfortunately until now it can't start normally. if I plug to AC, I can switch it on bootloader mode(only bootloader mode), but when I plug to my computer, I can't switch it to bootloader mode, so I can upgrade rom .
Can You help me?
Sorry, newbie question, but before I have to use my MDA Vario 2 as a door stop, does anyone know if it is possible to get out of the Multi Coloured Screen ? our office had a power cut while I was updating from WM5 to WM6 and now it is stuck on the following screen:
HERM300
IPL-1.01
HERM300
SPL-1.40.Olipro
USB or Serial (Depending if I have the usb cable connected)
Obviously I cant connect to the phone as it is not booting and Active Sync is not connecting so I can upgrade.
Am I buggered like a cat ?
FALSH ALARM !! Phew, Many thanks to Digbyi as I was able to re-set and re-load the ROM !
ok friends just some one try to help me here , i have ipaq 6965 and now is damaged first time it freez on hp logo and then when i try to make an upgrade i choose the wrong file so the ipaq can now enter only on usb mode and show me V0.19 on the bottom of screen and cant now more accept any upgrade , always stack on radio , so please is there any way to restore it by memory card sd ,? i see that in forum but cant find the correct file and how can i create a good sd card for restore . !! HELP HELP HELP HELP !!!!
Try following setps
I have same problem, Hp freez on Hp invent logo and usb screen.
http://pdaphonehome.com/forums/hp-hw...need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
thanks , but you forget that my ipaq was update with a wrong file so ur methode cant work ... any one have other solution plz !!!
thanks
ipaq dude said:
I have same problem, Hp freez on Hp invent logo and usb screen.
http://pdaphonehome.com/forums/hp-hw...need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
Click to expand...
Click to collapse
need some help too...
Did you follow the exact step above?
Hi There
I had a same problem, hp stuck at hp invent logo. I did above step exactly as it says, after following those steps my Hp is fix now.
Thank you
Well, I'll start from the beginning.
Yesterday I installed wmwifirouter 1.20 trial on my Uni, it worked great, when I finished using it I shut it down normally and all was perfectly fine. I'm not blaming wmwifirouter here, but I feel I must point it out as it was the last piece of software I installed.
I packed up my Uni, put it back in its slip case and started driving home. When I got home, I opened up the lid and it was dead. Fine I thought, battery was flat. So I charged it overnight (I have to use an external charger as my Uni's USB port broke off) and put the battery in this morning, Uni asks for initial Windows Mobile setup, WTF?
I panic, and I press the RESET button hoping that it will clear this problem and my Uni will work fine. Now it is stuck on the boot image, O2 logo with red text that says the following:
Code:
PU10 64Mb RAM
ROM image built:
Dec 31 2006
19:42:34
R 1.04.02
G 42.37.P8
D 2.01.06 WWE
I tried a hard reset (holding down both soft keys and pressing RESET, and then pressing zero key to initiate wipe), but it still doesn't get past the boot image..
Now, considering that my USB port is broken, is there any way to fix my Uni?
I have a 2GB SD card, and a 1GB MicroSD card with SD adapter, if this can help somehow?
try push light+power+reset and Yours uni should run i boot mode
read wiki - U'll find all solutions
FabianD said:
try push light+power+reset and Yours uni should run i boot mode
read wiki - U'll find all solutions
Click to expand...
Click to collapse
If I do that, I get the ROM flashing option, but that doesn't help me because I don't have a working USB port on my Uni
*BUMP* I need help with this please, I've not had a working Uni for days