XDA Exec won't recover from Bootloader Mode - JASJAR, XDA Exec, MDA Pro General

Hi all. I'm a little desperate. Following an attempted upgrade to Radio 1.06.00 I'm left with an Exec which is stuck in Bootloader mode, won't sync and wont flash from the O2 website flash installer.
Does anyone have any ideas? It's in warranty and insured.
Heeeeeelp

Try applying the 1.06 update again. Mine got "stuck" the first time, and I had that cold panic shiver of "oh god, what have I done", but it will go through the second time, I'm sure.
Cheers,
Steve.

Dear kinkybookworm,
Please unplug the usb cable.Deattach sim card and sd/mmc card and soft reset the unit.After you see " SERIAL " on the screen, plug the usb cable and reflash the unit with radio upgrade again.i guess that this will solve your problem...
Regards and thanks...

Related

SOMEBODY HELP ME PLEASE I THINK I'VE BROKE MY XDA IIi

i have an xda IIi an it say's serial v1.01 when i try to put it in the charger it say's usb v1.01 but activesync 4 will not detect it but it does connect to my pc without activesync but i can't install any thing on it. i have downloaded the original software from the o2 website but the installation instructions say it needs to be connected to activesync. what do i do
Hmm...Seem to me you are in bootloader mode serial connection version 1.01 .. Try checking the buttom. As this mode will only come if you press power+reset+navigator buttom.
i have tried soft reset and hard reset but i just can't do anything with it
chill..
download the rom image from o2 here is the link,
http://www.my-xda.com/xda2i_soft.html
put the device into bootloader and put into the cradle and let it do it's magic
simple!
PS, i problem like it i killed mine by messing up the rigistry i was screwed so i did that above and all was okay....main thing is not to panic always think u have the garuntee from o2 so u can take it back...so take it ez!

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

Bricked Hermes (SPV M3100) while flashing SPL - any help or sugestion are wellcomed

All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...
The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...
Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd
I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.
get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it
Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???

Cannot flash my SPV M650 anymore :(

Hello,
I have an unblocked SPV M560 (HTC3300).
Few weeks ago I have installed the B&B rom with WM6 on it. Now I would like to install the adinfinitum rom (http://www.adinfinitum.fr/wm6_gps_m6...d_and_the_ugly) to solve the GPS problem we can have with the M650 but I cannot flash anymore.
Here are some explanations:
After starting "start_uspl.exe" I get the Linux screen then the RUU application starts on my PC. RUU is trying to connect to the device but after few seconds it displays the error "ERROR[260]: Update error".
After this I tried to restart the pda, wait for Activesync connection and try to restart RUU.
This time RUU can connect, I can see the grey screen on the PDA and it starts updating... but after 2% I get a black screen on the PDA and RUU displays the error "ERROR[270] Update error".
I'm now reading this forum since 2 days and saw that other people already had this problem but I did not find any working solution.
Does anyone of you have an idea of what can I do to solve this problem?s
Thanks in advance for your help.
Alain.
REad this...
Remove sim and mem card from phone use clear storage to clean phone memory then again try start_uspl.exe wait to 100% finsh do not disconect phone and run then romupdateutility i hope that this can help mine problem is resolved and i flash spv m650 many times.
Hi, i have similary problem, when i try re-install WM on my xda orbit 3.15.118 i have alert : flashing error check your update utility..when i try install another WM6 i have alert : error 270:update error
battery full charged
anyone help me ;-)
Hi,
I finally managed to do the update. The only difference is that when RUU has started after getting the black screen I clicked on the cancel button.
After this I let the terminal with this black screen for few minutes (about 5 minutes) and starts again the RUU application.
And this time is works... don't ask my why, maybe it takes some time to the terminal to be ready to accept connections. At least now SPL 1.1 is installed and I can upgrade. My GPS is now working
Thanks
Alain
Spv m650 arte100
when i run the start_uspl.exe i have this window after the run
No Device Connected
Would You like to try copy again?
YES NO CANCEL
boy my SPV is in bootloader mode and i can't riun it in different mode
i have IPL 3.15.0001 and SPL 3.15.0000
What i have to do ???
PLEASE HELP ME

O2 XDA Exec (Universal) Won't Power On after Unccessfull ROM Upgrade

--------------------------------------------------------------------------------
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
dineshkumaar said:
--------------------------------------------------------------------------------
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
Try to reflash with another ROM
And maybe your battery is not working
Good luck and donĀ“t forget to vote!
Im new to this forum and spending a few weeks doing searches I have found a new world of things I can do with my M5000! Only problem is I have the same problem as this guy. The problem started with no GSM, No Protocol version and no IMEI number, After countless rom installs and failed all I thought I left the sim in? Took batt out, No sim, Put the batt back in and now it wont turn on or do anything.
Has anyone found a solution to this problem or its it an expensive paper weight?? Im lost without it!
ronnie5 said:
Im new to this forum and spending a few weeks doing searches I have found a new world of things I can do with my M5000! Only problem is I have the same problem as this guy. The problem started with no GSM, No Protocol version and no IMEI number, After countless rom installs and failed all I thought I left the sim in? Took batt out, No sim, Put the batt back in and now it wont turn on or do anything.
Has anyone found a solution to this problem or its it an expensive paper weight?? Im lost without it!
Click to expand...
Click to collapse
Welcome to the forum
You have a great device!
Have a look here:
http://forum.xda-developers.com/showthread.php?p=3999833#post3999833
Hope it helps and good luck,

Categories

Resources