Related
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
Hi Profs,
there are some problems with a Artemis Update SPL (USPL) v.01. I've found this problem is several topic but there was no solution for it.
#1:
http://forum.xda-developers.com/showpost.php?p=1739577&postcount=413
#2:
http://forum.xda-developers.com/show...44#post1745844
#3
http://forum.xda-developers.com/showpost.php?p=1713596&postcount=1
The problem:
use USPL to get rid of the CID....count goes up to 100% screen shows black with green text, then pops to white. I need to do a soft reset to get it running again.
Then i use ROM Update Utility to update my p3300....and it still keeps hanging on 3%....damn. i get mad...!! Have read almost all here online...no virusscanner, no firewall....I use win XP.
i even tried without memory card and phone card....and nothing seems to work.......
ipl 1.14.0001
spl 1.14.0000
gsm 02.07.90
os 1.14.0.0
Who has any clue...?
With other words:
I've just got back my P3300 from repair, they changed the main board. With the previous main board I was able to upgrade the device and I was using the B&B versions.
But with this new board I'm not able to upgade the SPL. When I try to upgade the device after and start the start_uspl .exe the 10...20... ....100 my device become an interresting "blue screen" status and only the reset help to get out from this status. If I start the RomUpdateUtility.exe after the upgrade I got the error message #270
IPL: 3.13.0001
SPL: 3.13.000
GSM: 02.94.90
ROM version: 3.13.405.1.WWE
ROM date: 8/28/07
ExtROM version: 3.12.405.102
This is not the solution for the problem. I've tried it:
Plug in USB cable. Hold voice recorder button and press reset button. Bootloader will appear (Three color stripes). Then you may flash up ROM. (This works only for RUU installation types, not for PDAmobiz modified installator) Original english HTC P3300 ROM you may download form here: http://wiki.xda-developers.com/index...temis_Upgrades ....
Please help us to solve this problem....
Probably the same problem
This should be the same:
Hello POF,
I was directed to this link by Rudegar because I want to change the french ROM to English ROM.
The relevant data of my PDA is:
The version of the ROM: 1.14.406.1 FRE
Date of ROM: 9/27/06
Radio version: 02.67.90
Protocol version: 4.1.13.28
ROM extension version: 1.14.406.101
I tried exactly the way you described in the USPL_manual and everything went well till I got to a stage where I was asked to click the update button which I did. After then there was a window which showed "updating from current version to version 9.99". I was confused at this point but clicked "continue" and after this stage I got an error message and there was no longer a connection bw my PDA and my computer.
Thanks,
Jonat
Reply With Quote
http://forum.xda-developers.com/showpost.php?p=1784337&postcount=430
Also the same
Problem "lost connection PDA-PC"
Hi,
first I would like to thank you for goooood job to many people here !
Back to my problem. I have HTC Artemis (T-Mobile MDA Compact III), OS WM6 T-Mobile Czech version.
I ran start_uspl.exe on my computer. The part in DOS based screen seems to finish everytime OK, but finally the connection with PC is lost. Therefore when the PDA Phone ROM Update Utility starts cheking version the error "lost connection with PC" appears . PDA stay in "black screen" mode and only hard reset start it again as usual.
Does anybody have the same problem? Any idea, how to solve it ?
Thanks
http://forum.xda-developers.com/showpost.php?p=1773030&postcount=426
When the screen goes white, don't restart. Just start flashing to the new ROM. Worked for me
Unfortunately it not a white screen, it a black one, connenction lost with the PC, and only the reset PDA helps to restart the unit again....
lenocs said:
then pops to white. I need to do a soft reset to get it running again.
Click to expand...
Click to collapse
What im saying is when it pops to white, dont soft reset it, just start the upgrade.
Anthony2oo5 said:
When the screen goes white, don't restart. Just start flashing to the new ROM. Worked for me
Click to expand...
Click to collapse
that what i also do When the screen goes white, don't restart. Just start your RUU
lenocs said:
Unfortunately it not a white screen, it a black one, connenction lost with the PC, and only the reset PDA helps to restart the unit again....
Click to expand...
Click to collapse
Same situation as above. Depending on the Artemis, the screen might go white or black. Just don't freak out and keep on flashing the USPL. It WILL work and then reboot. Then you can flash the actual ROM you want.
Hello from an absolut newbie trying his first upgrade,
And I have just experienced the same problem than lenocs.
I have run start_uspl.exe, but when the screen is suposed to become white or dark, it becomes dark and the artemis is in fact totally off and connection is lost.
Anyway I supossed that it was because the scrren got black and I tried to run the update utility, but I´ve got an error (the terminal is disconnected or similar) and nothing happens.
I have had to soft reset the terminal and fortunatelly it seems that I still have my previous ROM and it seems that it works. But, do you know if there could be some "side effect" because the first step of start_uspl script?
Anyway I would like to move to WM6, so, any suggestion would be really appreciated.
Thank's a lot
When you restart, what is the USPL number?
Ooopppssss!
I didn't pay attention.
As I've said, I'm a newbie, so I was just woried because I thought I had "bricked" my new atemis.
How can I know now the USPL number?
Anyway I tried the star_uspl again (I'm a crazy newbie) and it failed. The artemis went off almost inmediately.
Thank you very much for your help
SpiggyTopes said:
When you restart, what is the USPL number?
Click to expand...
Click to collapse
solved ... at least for me
I think the problem is in SPL version 3.13 (or maybe anyone newer than 1.11).
Try different Artemis USPL - for me worked version from this page:
http://wiki.xda-developers.com/index.php?pagename=Artemis_DumpedRoms
It's very confusional, because file sizes and also dates are the same as in unfunctional version, but this one worked.
Hope it'll help you as it helped to me.
Maybe this can help you
I bought a 8gb card the week before, so I needed to update the rom in order to have my new SDHC working. But whn I was trying to update the rom, through UPSL 1.1, I had an error. This was the first time I had an error because I have modified the room many times before. My error was about a CMD.EXE issue, something like Error code line 26 "can´t spawn cmd.exe" so I was not able to change my rom. What I did was to copy CMD.EXE from Windows/System32 and put in the same folder where I had the start_uspl file, and finally works!
Do not ask me why, but this was the only way I could make works the update process.
Just try.
Rocheau said:
I bought a 8gb card the week before, so I needed to update the rom in order to have my new SDHC working. But whn I was trying to update the rom, through UPSL 1.1, I had an error. This was the first time I had an error because I have modified the room many times before. My error was about a CMD.EXE issue, something like Error code line 26 "can´t spawn cmd.exe" so I was not able to change my rom. What I did was to copy CMD.EXE from Windows/System32 and put in the same folder where I had the start_uspl file, and finally works!
Do not ask me why, but this was the only way I could make works the update process.
Just try.
Click to expand...
Click to collapse
do u have ur card in the phone while updating
you are suppose to remove the card
Problem solved (for me)
Hi,
i had the same problem error 270, 3% and lost connection with Activesync.
IPL: 3.13.0001
SPL: 3.13.000
GSM: 02.94.90
ROM version: 3.13.405.1.WWE
ROM date: 8/28/07
any way to upgrade was wrong ->> error 270
My good way was:
1. Downgrade to WM5 - original shipped ROM 1.12.405.1(link found on Wiki pages)
2. Under WM5 run USPL to unlock CID (now without any errors)
3. Final STEP - Upgrade to new ROM Artemis Touch 3.01 (without any errors by upgrade)
))
Now my Artemis seems to be OK.
I ran USPL with storage card inside the device...
no problem
switch SD card back to 2GB or smaller before USPL
Hi,
for me USPL did not work with my SDHC 8GB card but then I switched back to my previous 2GB SD card and then it works.
Perhaps the SDHC driver blocks USPL in some way.
Cheers,
Markus
i have been trying for 3 months
once i have upgraded my artemis to wm 6.0 everything seemed to be OK for two days... then the screen started to go black when i restart... şi downgraded to 5.0 but nothing changed... when i remove battery for a while, my arte works... when i try to do anything with it, the screen slowly goes black as if it is broken... please DO HELP ME! i am going to go mad... i have a new iphone, ihave i kaiser as well... but i miss my artemis very much...
Hello:
I have the same problem and realized hundereds have too. I have been checking in all forums and no asolution to it
The issue that happens to me is that I used USPL for upgrading to WM6 and worked, but now for the Touchflo it does not. Tried with all USB ports, tried with different computers and no good news.
The USPL msdos screen indicates that there is no connection at all in all percentage levels, then it bocomes dark and the 260 error whne installing the rom.
please help us soon !!!
we are in trouble!!
Same Problem : Screen shut down
Anybody can help us on this point ?
The only way to solve it is to remove the batterie during 30 min., then put it back and pray...
Then, for no reason, the screen shut down, a few minutes or days after
I've upgrade from WM5 to WM6 with the original Rom of HTC, it seems a little more stable but it shut down every 2 days when i'm lucky
Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.
Have you tried updating to the latest version of Active Sync on XP
or following the guide for Vista
Take off battery. wait for about 10 hrs. put back battery and switch on the power.
Thanks for the tip's
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway
Furkinl said:
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway
Click to expand...
Click to collapse
erm u are trying to flash on a pc running vista?? thats your problem, u cannot flash on a vista pc, xp home/pro ONLY!
Thanks for the advice, tried on XP and it worked fine, it would seem that activsync was not required in this case. At least my XDA is ALIVE for now.
many thanks
You simply could revive it again by Resetting it via the stylus
thnx 4 all the soloutionsss
i had same problem , but once i tried it on xp, its works for me, my ppc now is refresh installed,
thnxx
qtek 2020i
for information the french rom is available on this place http://www.planete-htc.com/index.php?mod=download choose dangaard section there is two files to download
1. choose 2020i dangaard rom
you can not use it
2 download the radio file
it contains an exe called upgradeut make it in the directory of your dangaard folder and you will be able to flash it
it work also for pda stuck in serial usb
voila
qtek 2020i
radio file 1.04 two mega
do a hardware resett and it should be the phone back to defaults
XDA IIi V 1.01 Serial /USB
Hello,
I tried to update my XDA IIi from a new rom version found at o2.ie website but my XDA IIi is stuck and showing Serial on top and v 1.01 at botom. When i attach it with cardle it shows USB instead of serial.
I have tried Almost everything that i found on this forum in last three days.
Hard reset / soft reset/ new installation using different version etc.. but nothing worked for me..
Now I am really confused and can't find what to do.. Can any one from XDA gurus/ developer help me and sumarize what should i do?
Thanks in Advance
Zeeshan
Yes, i have the same problem i did exactly what was done above me pls can someone help!!!!!!!!!
Furkinl said:
Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.
Click to expand...
Click to collapse
Where can I download this rom?
Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed
Thanks in advance
Chet
look and lern
put qtek 2020i in stativ (conect to pc via usb)and push power ( on screen will apear USB and v1.01), and you dezarhive :astel_wwe_11100_112_10200_ship, and doble klik on AlUpgradeUt and bios at ppc wil be update !!!!! This is all, the ppc will be now reinstaling, be patient and wait until will be reinstaled (25 min)
Hy..
belive me.. i tried nearly everything... and ive been through all of these posts... but i dint find anything helping me out with my problem...
ok, i try to explain in a short way!
I want to upgrade my "old" xda orbit (rom: 3.4.207.2GER, Rom Date: 18.04.07) wit a new rom ( something like "Artemis_Touch_4.02_Full_with_4_sided_cube")
BUT IT DOES NOT WORK!
Yesterday i updated my "new" DIAMOND to a new rom (Bepe 0.94)... so i basicaly know what to do..
But my ORBIT doesnt like to be upgraded..
USPL: doesnt work
RUU: doesnt work
Artemis_Touch_4.02_Full_with_4_sided_cube: doesnt work
downgrade to wm5: doesnt work (dindt find the correct one, i guess...)
now i am out of any more idears... ive got a lot of error messages... such as 260, 270 corrupt files, and many more...
wonder why my orbit is still running after all these unfinished and unsucessfull "updates" but still running with original german O2 WM6 system.
Does anybody can give me a hind what do do, how to update or where to look?
Thanks a lot...
Using Artemis USPL: in the DOS window always the message "program cannot be found".. running aprox up to 50% and stops, than closing the DOS windo
the orbit stays, after a short action showing the Linux guy, with a "white/black" display..
than using the RUU: still connected via usb to my pc.. still black display..green LED on top of the device on..checking the rom.. showing mine correct (3.4.207.2) to 9.99
clicking "next": starting updating... pda display gets threecolored.. than gray.. showing 99% and than 100% after just a few seconds..
Prog stops.. telling me that the file is corrupt (Error 270).. my device reboots and starts with the O2rom
I downloaded the Artemis USPL several times from several locations.. always the same message...
Hard to explain.. but i hope you got my point?!
Btw.. thats just one of the ways i tried.. and just one of my errormessages..
Thanks
Did you tried to remove your SD card before you flash?
Cheers
I Got It I Got It
Thanks "Zecanilis" for your answer.. but that was not my problem.... i took out the sd card as well as the sim card.. as i said.. i tried nearly everything!
But this morning ( i spent the whole night in front of my computer ) i foud the mistake.... an easy one!!
The "Artemis_USPL" file, you can find in all of these threads, is not working with my devices (pc and/or ppc)!?! i dont know why.. but it doesnt.
As i told you i always got messages in the DOS window "program cannot be found", "program cannot be used"... and the intallation skipped all files and stopped always around 50%.
but at 3 in the morning i found a USPL file in the net, with a different name, and it worked with the first try!!
The File is named "arte_uspl".
Just worked fine and smooth 10..20..30....... finisehd.
I am able now to install any rom I like!
Btw... i swithed to Mossis V2.2Ger - a very nice one i think.
But maybe i'll try some more...... because i am able to!
Take care and a lot of fun with your devices!
Bobo
I have the same problem
Where can i find/download the "arte_uspl"?
Thanks for your help.
well...good question
i didnt write down the link.... i dint save the link... sorry!
what i did was to save the file on my computer!
i tried to uplad it to this post... but it didnt work?! sure i am to stupid to do it right!?
so plase help me to post it here, and i will do so!
or gimme a mailadress to send it to!
sorry for beeing so stupid!
greetings
orbit do not boot, do not flash
Hello,
i am searching for a solution of my problem:
i updated my orbit with the new mossis ROM and everything was well, and i used my orbit after this update!
Yesterday i Reset my device and after this the orbit dosen't start again!
After showing the bootsplash the device hangs
So i try to flash the device again:
first i try this:
- start the bootloader manually (voice button + reset)
==> shows: IPL 3.04.0001
SPL 1.11.0000
- starting the ROM Update Utillity
==> the screen of my orbit is grey and shows the update bar (0%)
==> RUU shows the following mesage: ERROR[300]: INVALID UPDATE TOOL
(i used the original german o2 update file)
second try:
update with the SD-card:
- SD-card (512MB) formated with FAT32
- copy the image file xxxx.nbh to the SD-card and rename it to ARTEIMG.nbh
- start the bootloader manually (voice button + reset)
==> screen: Checking SD contens
==> Update SD Image?
- bushing the volume down button
==> screen is red green blue and shows IPL 3.04.0001 and SPL 1.11.0000
Update flash do not start!!!
if i try this sd-card based update with the RUU_uspl_signed.nbh file, the device bootloader start and update the ROM
have anyone an idea???
ohs said:
Hello,
i am searching for a solution of my problem:
i updated my orbit with the new mossis ROM and everything was well, and i used my orbit after this update!
Yesterday i Reset my device and after this the orbit dosen't start again!
After showing the bootsplash the device hangs
So i try to flash the device again:
first i try this:
- start the bootloader manually (voice button + reset)
==> shows: IPL 3.04.0001
SPL 1.11.0000
- starting the ROM Update Utillity
==> the screen of my orbit is grey and shows the update bar (0%)
==> RUU shows the following mesage: ERROR[300]: INVALID UPDATE TOOL
(i used the original german o2 update file)
second try:
update with the SD-card:
- SD-card (512MB) formated with FAT32
- copy the image file xxxx.nbh to the SD-card and rename it to ARTEIMG.nbh
- start the bootloader manually (voice button + reset)
==> screen: Checking SD contens
==> Update SD Image?
- bushing the volume down button
==> screen is red green blue and shows IPL 3.04.0001 and SPL 1.11.0000
Update flash do not start!!!
if i try this sd-card based update with the RUU_uspl_signed.nbh file, the device bootloader start and update the ROM
have anyone an idea???
Click to expand...
Click to collapse
Dear ohs,
There are many ppl, who have this Error 300 issue, but there is no help/solution available anywhere. Maybe the best option is to send your device to HTC, I guess they'll replace your motherboard, if in warranty you'll be lucky!!! unless they find out if you have messed up the device
xda orbit
same problem here,i tried eveything,my xda orbit wont flash it starts to instal the new rom but when it reaches 3% it resets himself ...any sugestion guys ? i tried upls,hard-spl etc arthemis rom everything . help please
Guys, I would suggest, if your device is under warranty, do send it to HTC Service center rather than breaking your head with it. Even I have been through such problems but ultimately I sent it to the service center and expecting my device in a couple of days with a motherboard changed.
If your warranty is not valid anymore then you are in trouble.
Good Luck
Xda Orbit
dose anyone knows the right stepts to flash this Xda Orbit German rom with a wwe rom ? please post it so we can try,i have this xda for 1 year now and iam still using the german rom on it,i what to start to use it but what can i do ? learn german ? somebody help ! i tried to flash it with RUU_Artemis_O2_UK_3.4.206.2_4.1.13.50_03.06.90_Ship all gose well untill 3 % from update the xda resets and gose back to his rom,please help me out ! i`ll mae a donation for this cause ! Thanks
arte_uspl
bob75 i found the rar arhive for your arte_uspl the link is : http://rapidshare.com/files/36943423/arte_uspl.rar
i have the rom updater SP3_WWE_2.4.33.11, and i go in all the processes, i am connected with activesync and when it goes to tri-color menu the phone looses activesync connections and it says that cannot have connection and freezes. what can i do? please help.
I've the same problem i sitll can solve it n anybody please help am new here i've no idea what to do. I tried unlocked CID but i couldn't do it put cert.cab in phone n wen i try to install it says can not install or SDA_applicationunlock n I also tried lokiwiz procedure but still can not solve it so please if someone could help me in updating or upgrade my Orange Spv C500 ROM so it would be so nice of .... Waiting for kind reply !