Database Users

what can i do for my xda 2? please help me.please guys.helpp

i was installing new rom on my device.when it was 12%, the computer got locked and i had to reset.Now,my baby did not reflash again.i tried again but himaupragadeutility gave : communication problem. what can i do now? can anyone help me? so a few people know this device, the others even do not know what pda is. what i can do?????????????????????????????

Try putting your device into bootloader mode and making sure your XDA is plugged into the mains as well. There's also an upgrade program which bypasses country id checks.
Good luck.

I got the same problem with my Qtek 2020i today!!!!!
The device is dead and i can't put it into bootloader mode!
I need your help please

Try taking the battery out for about 1 hour. This will run the backup battery down therefore wiping the ram. Put the battery back in, connect it to the mains and put it into bootloader by pressing power, action and reset for about 3-5 seconds until serial appears on screen. No backlight so look carefully.

I tried to remove the battrey for 1 hour but it's still the same!
any way thanks for trying to help pug.

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

Still Stuck @ Boot Loader - time to send for repair?

Hi all,
I'm writing just because i think now is time to send my TyTN for repair, but I want other infos if someone can help.
Today, after I've charged all the night (about 6 hours) my TyTN, when i've pushed power button it started with Boot Loader.
I thought well, it's time to upgrade the ROM, i've already saw this screen experimenting on functions but, to me sounds strange that the device started automatically in Boot Loader.
The ROM was ROM version 1.18.258.2 ROM date 07/22/06
I've downloaded a new (official) release ROM version 2.11.258.1
ROM date 03/07/07 and followed the instructions with Active Sync but obviously it dont started.
Searched and found how to upgrade with MiniSD and HERMIMG.nbh.
Successfully loaded the new ROM and device still restart in Boot Loader.
I've then connected to the wall plug and done an Hard Reset, Windows Mobile showed up right.
When the installation for EXTRAs ended the device restarted and NOW STILL in BOOT LOADER mode.
I've readed and tried everything on stuck Boot Loader and other topics but cant get out.
The thing that is very strange to me, is that I'm unable to use mtty or get connected to use uni_exitbootloader.
Another thing is that the device no more charge the battery or Amber lights on, only RED light with USB cable or Charger.
(Problem 6 @ http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#other)
Finally I think is something USB hardware related and I'll send it for repair but just want to know if there something else I can try.
(maybe is better I post here? DEAD Hermes @ http://forum.xda-developers.com/showthread.php?t=286755)
Thanks in advance for any infos anyone can provide.
Marco.

Finally
I've tried with solution found on
http://michael-channon.spaces.live...._c=BlogPart&partqs=cat=Hermes+Charging+Issues
additional power batteries self made pack of 3 AAA Batteries worked for now.

Bricked Hermes (SPV M3100) while flashing SPL - any help or sugestion are wellcomed

All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...

The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...

Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB

Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset

@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd

I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.

get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it

Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???

Bootloader no USB?!

Hi all, started to try and get phone onto android last night.
Followed the guide for HSPL3 then started started to update radio but got error about USB!
Booted into boot screen to see whats going on (volume down) and it wont go past loading! just sits saying loading!
The device boots ok and i get windows (eventualy! if i wait) Once booted into windows USB works but in the bootloader i cant get USB!
I have pressed volume down and red button and in white box it stays on serial!
I have googled for hours any pointers?

GazWales said:
Booted into boot screen to see whats going on (volume down) and it wont go past loading! just sits saying loading!
Click to expand...
Click to collapse
grey screen, writing in blue? sounds like it thinks you have a rom on your sd card. try it without the sd card in.

Thanks for you suggestion - tired that already should have said.
The issue is fixed however - I took out SIM aswell as SD, manualy booted to loader. Waited 5 min then it changed to USB! Quickly opened HSPL3 an re flashed.
Issue was still the same! So followed same procedure and used HSPL 1.6 that fixed it! I can then flash with a rom suitable for Android!
Flashed 4 min later, put Android on - now loving my new phone - its amazing the difference! This is how the HTC HD2 should have been!

heh, lucky you, i've tried android on 6 different occasions now, first four times i wasted some hours and never got it to boot, 5th and 6th time it worked, but when i restarted, the phone wouldn't restart without a hard reset, so i'm not touching it again for at least another three months.

Thanks. Your solution worked great. As soon as I pulled the SIM and waited a few minutes it popped right up. You should mark this thread title as solved

@samsamuel try using nand its alot easier to install and there are some great builds on this website!
Sent from my Gingerbreaded HTC HD2 using XDA App

Hi there,
the problem is not solved for me!
I flashed my HD2 several times before, using winXP. Now I got a new laptop with
Win 7 64 bit. I want to flash my phone with a WM6.5 Dutty ROM. The phone syncs fine when running but when it switches to bootloader, the laptop doesn't recognize the phone anymore. It does not switch to USB and on the Laptop I get the message that there is no driver for "Qualcomm CDMA technologies MSM"
Help please, I tried to find some answers but couldn't find anything!
Thanks.

klumpbatsch said:
Hi there,
the problem is not solved for me!
I flashed my HD2 several times before, using winXP. Now I got a new laptop with
Win 7 64 bit. I want to flash my phone with a WM6.5 Dutty ROM. The phone syncs fine when running but when it switches to bootloader, the laptop doesn't recognize the phone anymore. It does not switch to USB and on the Laptop I get the message that there is no driver for "Qualcomm CDMA technologies MSM"
Help please, I tried to find some answers but couldn't find anything!
Thanks.
Click to expand...
Click to collapse
Mate, check my suggestion at your other post (you started a new thread today!)