Database Users

what can i do for my xda 2? please help me.please guys.helpp

i was installing new rom on my device.when it was 12%, the computer got locked and i had to reset.Now,my baby did not reflash again.i tried again but himaupragadeutility gave : communication problem. what can i do now? can anyone help me? so a few people know this device, the others even do not know what pda is. what i can do?????????????????????????????

Try putting your device into bootloader mode and making sure your XDA is plugged into the mains as well. There's also an upgrade program which bypasses country id checks.
Good luck.

I got the same problem with my Qtek 2020i today!!!!!
The device is dead and i can't put it into bootloader mode!
I need your help please

Try taking the battery out for about 1 hour. This will run the backup battery down therefore wiping the ram. Put the battery back in, connect it to the mains and put it into bootloader by pressing power, action and reset for about 3-5 seconds until serial appears on screen. No backlight so look carefully.

I tried to remove the battrey for 1 hour but it's still the same!
any way thanks for trying to help pug.

Prophet upgraded with Wizard ROM by mistake

Just tried to upgrade my S200 with a 9100 ROM ver 2.8.7.1 WWE (by mistake of course) and I can't turn it on anymore. Somehow it didn't even warn about wrong ROM.
Tried to hardreset it but no luck. When I keep the camera button it goes to RGB only when connected to the charger.
When connected to PC, the red and blue leds keep flashing and my PC gives Error 260 when I try to revert back to the S200 RUU.
Does anyone know how to bring it back to life? Is there a way to boot it from SD card?
-
I-mate Jam
Qtek 9100
Qtek S200

Don't panic!
I did the same thing some time ago!
What you need to do is make sure that the battery is fully charged. (The flashing of the screen can be a result of the flat battery.) Unfortunately, it is not possible to charge the battery when the wrong ROM is installed, as the ROM obviously tells the Prophet how to charge.
Let's assume you have an okay battery.
1) Start the Prophet in Boot mode. This is done by pressing and holding the Camera button and then pressing the soft-reset button. Keep holding for about 7 seconds, and the coloured bands should appear.
2) Connect to PC using the UDB cable.
3) Run the correct ROM upgrade. You do not need to be paired with ActiveSync, as the update programs are intelligent.
4) If the update does not work (and it fails at 95%), then try again. If it still fails, try again and do a soft-reset mid-way through. This will kill the ROM upgrade and you should then be able to do it fine after that.
The really important thing is that the battery is charged before you do this. Unless anyone makes a USB cable that can charge AND connect to PC, then a fully charged battery is a must.
Let me know if this helped.

Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!

Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!

Re: Boot from SD?
zealerc said:
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Click to expand...
Click to collapse
I am a bit confused, does that mean that ALLOW USB CONNECTIONS has to be chacked or unchecked?
I did the same exact mistake. Now, my baterry is fully chaged (which I can check on another phone) but when I put it in S200 it shows that the battery has 0%. Conseqeuntly, when i unplug the power cord the phone dies. I have no way of running the new ROM on it. I tried running a bootable SD but it only installed part of the software. i read on this forum that such a thing happens and that one would need to run a full version ROM from a computer. So, how do I do it??? I am almost giving up all hope of ever making this phone work
Does anyone have a file to boot from SD and is it possible to run a full ROM from SD. Please help!

HELP iPaq HW6965

HELP iPaq HW6965 FREEZ ON START UP only hp logo on screen and fone cant connect to pc and cant put it on boot mode , any advise please or how to realy put in boot mode ? thx in advance

Enter Bootloader mode !
To enter bootloader mode press simultaneously the two front buttons (the left and right of the keyboards joystick) and the soft reset with your stylus, but you must put screen under the bright light or you wont see when your iPAQ will go to bootloader mode. Then you put USB cable from iPAQ to your PC and you will see if iPAQ detects USB craddle. Then you tray to update iPAQ with french ROM and this is it. Try this and report.
Best Regards,
Drahtman

before bootmode try to take out your miniSD and then try HR
power+send+end+SR
it is trky so may not work for the first time
so try till you make it right
good luck

drahtman said:
To enter bootloader mode press simultaneously the two front buttons (the left and right of the keyboards joystick) and the soft reset with your stylus, but you must put screen under the bright light or you wont see when your iPAQ will go to bootloader mode. Then you put USB cable from iPAQ to your PC and you will see if iPAQ detects USB craddle. Then you tray to update iPAQ with french ROM and this is it. Try this and report.
Best Regards,
Drahtman
Click to expand...
Click to collapse
phone cant go on boot mode only says done or somthing else and restart on hang screen hp but no boot mode sucsess , any advise plz ?

Pls help ti solve NO GSM problem!

Could anyone can help me to solve No GSM poblem. I think there are many other users have same problem.
After it faild during update rom, My HP6915 represent NO GSM during booting and the phone funcation also doesn't work. But in HP Asset you can see it, just no firmware, no version number. I try to flash english radio rom and french radio rom, but always stop at 1%. This matter appeared after I flashed orange rom(french version). I think it locked by Orange.
Does any one can help us?

did you try the update with no sim and no minsd?

EREZYAD said:
did you try the update with no sim and no minsd?
Click to expand...
Click to collapse
Yes, I update without sim card and minisd. Always stop at 1%

to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck

EREZYAD said:
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
Click to expand...
Click to collapse
Thank you for your reply!
I tried but still same, stop at 1% when I flash Radio WAN OS, stop at 2% when I flash Radio FS. I tried to unlock simlock and CID unlock, but it doesn't work on my 6965

called a few places looks like the radio chip is fried. sorry man...not looking good.

try update again with this method
I got almost same problem. I tried to update GSM rom but update fail and my ipaq stuck at hp invent logo. try following steps to see if it works for you
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider

I also meet such question.

actualy. I met the same problem "No GSM" after wrong update. I thing I tried everything, but I Didn't try to flash the device via mini-sd card. I don't know the right address for GSM area. Did anyone know?

caoxt said:
I also meet such question.
Click to expand...
Click to collapse
COME ON guys some one can help us , i have too the same problem please help with radio stack !!!!!!!!!

me too,, really nedd help here.. my only phone sable...

Hp 6945 Stuck at Serial and Hp invent logo

Hello Everyone
I need big time help. I just bought Hp 6945 and I tried to update GSM rom from 1.02 to 1.08, while updating it says update fail and try to restart Ipaq and start again. Now My problem is Ipaq just stuck to Hp invent logo. I tried to reset and hard reset and remove battery but notthing work.
I need help
Could some please help me to How to fix this problem?
Thank you

same BS happened to me. the only way to fix it is to load the UK 6915 ROM. thats the ONLY way to fix it. AVOID this update do not try to update the radio. I bricked my phone doing this. STILL looking for a solution. Radio stack is daamged.

where Can I find Uk 6915 rom
Thank you for reply. Where can I found the UK 6915 rom. Is there any instruction to How to load rom?
Thank you

If is FIXEDDDDDDDDDD
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider

No network connection
Ok everything work fine, but Now I cann't connect to tmobile. It keep showing me no service.
Any Help please

Ok It is fixed again
There is another update at HP website, which is software update. After installing that everything working fine.

can anyone help? i just bricked my ipaq 6965 too. had already followed those few instructions without any success.. what do you mean by "with or without SIM card"?

After a soft reset, mine's stuck at the initial blue/white boot screen.
Hard reset doesn't work (assuming its call + hang up + power + poke reset).
Ideas?

bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845/Ipaq_HW69XX_ENG_ROM.zip.html

download files from rapidshare posted by me ,r tested on my phone

hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you

garyakw said:
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
Click to expand...
Click to collapse
If you are stuck on a HP Invent Screen, with G.39, etc.
And you have tried to hard reset and softreset with no luck, this is what you do.
XP Instructions:
1. Download this link http://www.mediafire.com/?3ygfbx0sjdy
2. In the taskbar area in the right hand corner, right click on activesync, bare with me, I'm using Vista and have to remember this, click connections..., you need to uncheck everything click ok or apply...
3. press ctrl-alt-delete, end process wscescomm.exe, (named something like that, end the process.
4. Extract the file you downloaded if needed.
5. Connect your device to the usb port on your computer.
6. Run Uni Exit Bootloader Application. Done
Vista Instructions:
1. Download these 2 links, and extract them if necessary.
http://www.mediafire.com/?3ygfbx0sjdy
http://www.mediafire.com/?9pmjkponfsg
2. Start Device Manager, (Start-Control Panel, Class View[Far Left Corner])
3. Connect HW6900 to USB port, you should now see a Mobile Devices (Next to + sign), Double Click
4. Right-Click on the Device, Click Update Driver Software, Choose let me pick from a list, Uncheck compatible hardware box.
5. Click have disk, Browse to location where USBAS is extracted, choose the wceusbsh.inf file, Double Click.
6. You should see Microsoft USB Sync, if not and it reverts back to the already installed file, and the box rechecks itself, uncheck it, choose microsoft, and choose the latest Microsoft USB Sync to install
GOOD LUCK

in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...

i get error 402.... times out and no can do.... what was that about german language... maybe i just need it spelled out. which screen does the unit need to be in. there is two... monochrome serial vs usb and there is the hp logo blue and white screen frozen indefinitely... please help i love this phone...

Hi, the rapidshare file is missing!
Could you give working link or send me the file to mail, please?

ipaq dude said:
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
Click to expand...
Click to collapse
Man,r u sure the above can work well???? Confusing......I did the above like u indicated,but it's not work on my device HP6915,could u make it in details how u fixed the problem of updating ur device,thanks!
Regards,
Brose

Thanks, This help get me out of freeze
Thanks for posting this link. It brought my hw 6945 back out of the freeze. Stay away from HP's site update. Bad news
johnnynomadic said:
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
Click to expand...
Click to collapse

Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.

Maybe
Most Likely Yes
bmw2320 said:
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Click to expand...
Click to collapse

cdguider said:
Most Likely Yes
Click to expand...
Click to collapse
I don't think so,Curtis.....But as I know most of dopod device hardly be dead....