I was upgrading my Jasjar with the latest ROM (March 9 release) but my PC lost the ActiveSync connection. Now I cannot start up my Jasjar. My computer does not detect the device and when I do a soft reset, I am stuck on the screen which says - 'Press 0 to restore factory default. Press X to exit;.
When I press 0, the screen goes blank and nothing happens.
Any suggestions on how to recover from this? Am desparately looking for a solution.
Thanks
Anand
Hi,
install one more time file radio.nbf only and restart the device.
Regards
How can I do that? My computer does not detect the device in ActiveSync at all now.
Anand
Run MaUpgradeUt_noID.exe (find it by google) from directory with radio.nbf.
Regards
Related
I have just installed SPB Clone correct on my Vario. Now this program did a soft-reset and the Vario just hang on de first bootscreen. (The one with the soft-/firmware version on it.)
SPB Clone has installed a program that would startup at first program while booting. My Vario don't seem to like that.
Is there a way to remove this program/problem without a Hard-reset. I don't like to lose my data.
I had the same problem..
you can only erase all data by installin the rom on top.
boot in USB mode, Hold the camera button and the reset pin and it will start in tree color mode, USB
Than install a rom from the computer... about 10 min.
A.
Do you have more information about that, what it does and how it works.
1) Fist you will have to find a rom update or corrent version of your phone.
I don't know what you have K-Jam or qtek 9100..
K-jam rom you can find at the support site, club i-mate
Qtek:
http://www.beyondthetech.com/blogs/kjam/2005/11/qtek-9100-rom-available-for-download.html
2) Boot the phone in USB Mode: Hold camera batton on the side and with the pen into the reset hole. USB screen will come up.
3) plug USB cable into computer, and run downloaded software.
10 more minutes and reset phone, all done....
Good luck
Clone is very dissapointing, I am using Sunny Backup Manager 3.7 now!
i had this problem too after installing SPB pucket plus. do you have this installed? if so just goto the options and uncheck safe mode and it should boot fine now, obviously wont help you until you have wiped the machine, but it will avoid the same problem again
I wanted to sell my phone so I hardreset it (my c500 has wm5), but it didnt worked and now the phone only starts till orange screen..
Ive googled and the only way is to flash wm5 again on the phone, but the problem is, windows xp doesnt recognize my c500, so i cant flash it back! What must i do now!! Please Help!!!
hey this will help you
Press Alt+Ctrl+Del and kill task wcescomm. then go to mtty establish an usb connection. when the white screen appears press enter i'll se a cmd:>
Download the wm5.bin ROM and copy to c:\ for example. return to mtty and write l c:\wm5.bin and that's all (l = small L)
Guys,
I ve just downloaded this http://rapidshare.com/files/21256078..._DUT_11500.rar romversion in the understanding that it was for the HTC 9000 PDA. There was a file called MaUpgradeUt_noID.exe which I let 'upgrade' my 9000. However, I think something very VERY big went wrong! A reset by pushing the 2 buttons and reset button on the back gives me the option 0 to reset but all I can see after that is a black screen which says USB at the top and at the bottom v1.00
What happened and is this the end of my PDA? Sync won t work anymore now since my PDA can t be detected by windows because I can t get in the PDA!!!
Is there something I can do??!!!
PLEASE HELP ME OUT!!!!
Edit/Delete Message
sounds like you're just in bootloader mode
I think you are in what's called bootloader mode. Read the wiki to check - the screen you are describing sounds normal to me you plug you device into the comp via usb (with sync over usb disabled in active sync) then install a new rom.
You really shouldn't have tried to flash your rom without reading some instructions first but I think that your device should be fine.
If you have already upgraded your rom just do a hard reset and select the option to reset.
Will this thread help?
http://forum.xda-developers.com/showthread.php?t=310056
I'm sorry, this is the thread I ment to link:
http://forum.xda-developers.com/showthread.php?t=310054
strangely enough I found out that I DID use a good version picked from this http://forum.xda-developers.com/showthread.php?t=298020 post. In this thread mwang gives a link to here http://buzzdev.net/index.php?option=com_phorum&Itemid=125&phorum_query=read,40,30486,30486#msg-30486 where I picked the dutch version. I than double clicked the MaUpgradeUt_noID.exe file and the software for upgrading started. When he was at 100% he said the the ROM update was completed and that I had to do a reset. So, I than pushed the three buttons (2x the - button and the reset button at the back of the 9000) but all I than see is the bootloader menu with USB and V1.00...........
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
sanderh said:
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
Click to expand...
Click to collapse
Rather late now, but if it's owned by your company for work, should you really be di**ing with it?
Solution to probl: Stuck in Bootloader
The one way of fixing your problems....you're officialy stuck in bootloader,
Here's the way to fix it:
1. Stop Activesync USB connection on your machine under connection settings.
2. Uni : Reboot Bootloader then Connect USB ( If your phone isn't in bootloader already..)
3. PC : Run mtty1.42.exe ( Download from XDA's ftp site or search the forums, I'm sure you'll find it.)
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5.1 Press Enter
5.2 USB> (This will show up)
6. Type: Set 14 0
7. Press Enter
8. Run your rom update again and it should flash this time.
did it start??
did it start?? ?
Hi. first post.
Have an o2 exec. Different brand same deice and none of the other methods worked but finally got it working. Using mtty1.42.exe it would not see usb connection and therefore could not go down that route.
I booted into the bootloader mode that says serial at the top and v1.00 at the bottom.
Connected to the pc and cant remember if i stopped wcescomm.exe or not but you can try both ways.
Then started Midget_1990_v1_0_PU10_WWE.exe rom and followed the instructions and voila.
Hope this helps someone.
"Using mtty1.42.exe it would not see usb connection"
You need to disable the usb connection of active sync under connection settings and then only mtty will pick up a usb connection..
hey guys, over the past few days ive had battery problems with my iMate JAMin, i got a new battery, insert it, and power on my device, now, rather than loading up the iMate image, it goes to the tri-color boot screen, i've tried a Soft and Hard reset, no luck , any one willing to try and help solve this problem, please email or PM: [email protected]
Will installing a new rom fix this problem?
Aidenkidd.
From the wiki:
wiki said:
If during an upgrade your Prophet fails to start properly or can only enter bootloader follow this:
Recovery
Download and install the latest version of ActiveSync (Google for it)
Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from
here (any part one) or
here
Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
Plug the Prophet in via USB
Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder
Disconnect the Prophet, and then re-enable the connect through USB.
Your Prophet should now work!
Click to expand...
Click to collapse
I wrote it any way, but since no one reads it I may as well post it here.
Hi everyone,
I recently received an XDA Orbit 2, literally, charged it for 2 hours, and when it was full charged, I started using it, I had it for about 2 months now, and recently I changed my home Internet connection to wireless (It's a B & G connection) so my laptop connects fine, and when I tried to connect my XDA Orbit 2, it connected and then soft-reset itself, and now it just loads the O2 screen, then Windows Mobile screen with the volume controller and I can't do anything else so here's what I have tried so far:
- Soft reset
- Removed battery and SIM
- Since I can't access phone's menu at all, I tried to Hard Reset method by holding the 2 soft key, reset, and the power button - So I get the warning that everything will be lost and to press 'Send' to continue, so I press the green key, and soft resets and goes back to the same situation again.
- The latest thing I tried is to load the Hard-SPL into the SDCard which has been formatted to FAT32, so loaded the POLAIMG.nbh into the root. and loaded the phone into BootLoader mode (Camera and reset buttons). It loads the memory card and just says 'Loading ... ' I left it for about an hour, until the battery died completely (I'm sure it's not supposed to take that long). And still the same problem.
I'm not sure if this phone is now bricked, can anyone help me plesae. I really need this to start working again, I don't have any info. on it. (Everything was sync. previously).
Kind regards,
Since you havent really messed with SPL, i would say to take it back, since its still into warranty.
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
htctytnowner said:
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
Click to expand...
Click to collapse
I assume just boots into bootloader and then stays there?
If yes you culd try searching out a thread on MTTY and recovery from boot loader but I dont know how well that would work on polaris as I have not tried it yet.
HTH
Leon
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
htctytnowner said:
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
Click to expand...
Click to collapse
Only in the ELF forum
Here:
I'm pretty sure you can download MTTY from here and read through how to use it.
http://forum.xda-developers.com/showthread.php?t=347700
Also it is worth checking the wiki and searching
http://forum.xda-developers.com/showpost.php?p=2054848&postcount=38
Please do some research! I have not done this before and I have no idea what the commands do!!!
pqillu said:
You can try this:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
THX to christonge
Good luck.
PQillu
Click to expand...
Click to collapse
Please Heeelp!
I wa installing a rom from todopdas.es an my Polaris doesn´t pass from the screen where´s said "smart mobility", and R1.58.21.23 G 25.65.30.04H D 1.52.00.00, please what I can do?
You need to do Hard Reset, all information will be wiped off. To do hard reset, hold down the:
1.Press and hold the GPS/MESSAGING and INTERNET EXPLORER
buttons, and at the same time, use the stylus to press the RESET
button at the bottom of your device.
2. Release the RESET button, but
continue pressing the GPS/
MESSAGING and INTERNET
EXPLORER buttons until you
see this message on the
screen:
This operation will delete
all your personal data,
and reset all settings
to manufacturer default.
Press Send to restore
manufacturer default, or
press other keys to cancel.
3. Release the buttons, and then press SEND on your device to perform
the hard reset, or press any other button to cancel the reset.
Good luck.
Hi,
I'm using an HTC TC POLARIS100. Today I upgraded my ROM and SPL successfuly. If you're still in trouble and believe the same process will help, I will let you know the process followed.
GUY