Related
I got a used wizard today,it is a few weeks old I also got a cradle with it.
I pluged in the cradle to the USB port and the charger to power, after playing with it for 1-2 hours I placed the wizard on the cradle to charge and after a few mins i noticed that it was over heating. I removed it from the cradle right away and noticed that the battery was droping 1% every minute or so. After it was down to 27% i removed the charger and left only the usb connection and placed the wizard on the cradle again. it was charging fine, when it was up to 90% removed it from the cradle and again was droping fast.
When it was down to around 25-30% of the battery I did a soft reset and since then I can never get it to start again also the red charging light does not show.
What the heck is wrong with it? I also get a light burning smell from the bottom of the wizard where the connector is located.
Any help?
I need your lights guys.
Don't like the sound of the light burning smell, that sounds like an electrical fault. It looks like your battery has died and the wizard battery setup is well known to do this. You need to plug it into the official mains charger (not the usb one) as this has an output of 1A, enough to kick start the wizard battery into life and start the charging. You need to wait a short while though before the light comes on. If this fails try to get a new battery and try that. Any more light burning smells and it needs to go back to the supplier.
I would suggest that you send it back to replace/repair. The rapid dropping of the battery power suggest that it is using power somewhere (illegally). I've heard cases of battery caught on fire, etc. and I won't suggest you to use it anymore until you sort out the 'burning' smell.
First of all thanks for your replys.
I pluged the charger on it and the red charging light came on after a while.
charged for over 6 hours and its still red? I think after been charged should change to green? right?
anyways after all that still doesnt want to turn on. I got it to start a couple of times but only to the point that shows the splash screen with the rom numbers and then it turns back off.
Should I give it a smash across the room on the wall? done that with some other things and worked just kiding.
Forgot to add that up to the point when i did the soft reset the device was working fine except the charge drop. Soft reset was done while it was working ( turned on)..... if thats any help.
i thinking u need flash phone with jafwm
and here u will find 3 flashs
www.gsm-support.info
fonec said:
i thinking u need flash phone with jafwm
and here u will find 3 flashs
www.gsm-support.info
Click to expand...
Click to collapse
That ain't gonna do jack sh1t to it. If it can't start to get into bootloader, it can't flash....and it's not a flash issue.
Usually the red light means power but not charging - happens to my qtek 9100 when I let it get too flat and I have to remove and insert the battery while the mains adaptor is attached - others have to 'jump start' the battery by directly connecting to a PSU - I wouldn't do this with yours.
From what you have said it sounds like a short somewhere. Any signs of water damage? Warranty? What Wizard do you have and what country are you in?
Richard
I got the wiza 200 O2 xda mini S from a guy in UK from ebay. The idiot sold me a cradle for it with an adaptor that says 12V on it (Like an idiot that I am i just noticed that) but then again how am I supposed to think that he gave me an adaptor that its not made for it when it says on the back of it "for Imate - Kjam". Do you guys think thats what burned the **** out of the unit ?
dont forget that some times turns on shows the ROMS numbers and turns off.
No water damage... I think its on warranty... I live in Greece.
Might not be the cradle - it could be it steps down internally to 5v. Use a meter and check what it outputs to the phone. Warranty with XDA's are 2 years to the *original* purchaser. As they are only supplied with an airtime agreement then that isn't you.
Richard
have you tried changing batteries to a new one? Seriously, thats the easiest thing you could do right now and you could actually get results.
Ok this is what I did.
Removed the baterry from the device,
got a 12V 1 Amp power supply that I had lying around and give it a few shots connecting it to the battery giving it an electro shock.
(If you're going to try this be very carefull.<<<< DONT LEAVE the power supply connected to the battery>>>> just give it a few shots 1 second on and off.
That was it.
It started working, device turned on and now its charging (I think) yellow light is on.
I'm going to leave it on for a few hours and see what happens.
Wish me good luck. I'll let you know soon.
ok... this is what happend.
Battery is drained and its not charging due to a blown fust on the main board.
I open the phone and placed and solder a little wire over the fuse.
Still does not charge. ^%$#%$#$^%$*
Before I replaced the fuse or should i say short it the yellow light would come on for a few min and then red again. Now when I charge the battery with another external power supply the pda comes on for a few mins and then dies again. ( no charging light whatsoever).
Does anyone know where to get a mainboard for it and about how much it costs?
Asking for help again.
SmartMan said:
ok... this is what happend.
Battery is drained and its not charging due to a blown fust on the main board.
I open the phone and placed and solder a little wire over the fuse.
Still does not charge. ^%$#%$#$^%$*
Before I replaced the fuse or should i say short it the yellow light would come on for a few min and then red again. Now when I charge the battery with another external power supply the pda comes on for a few mins and then dies again. ( no charging light whatsoever).
Does anyone know where to get a mainboard for it and about how much it costs?
Asking for help again.
Click to expand...
Click to collapse
Hey man, sorry to hear about that.
The best you can do is to claim your money from ebay.
You probably killed it when you pluged in the 12V PSU. That's 230% of the normal Volts! Otherwise sell it for parts.
I'm in the process of claiming the money back from the IDIOT that sold it to me.
Lets see if that part of Ebay works as good.
SmartMan said:
I'm in the process of claiming the money back from the IDIOT that sold it to me.
Lets see if that part of Ebay works as good.
Click to expand...
Click to collapse
Doubt it. Did you ask the seller for help before opening the phone and voiding the original warranty on the device?
SmartMan said:
ok... this is what happend.
I open the phone and placed and solder a little wire over the fuse.
Click to expand...
Click to collapse
Not a good idea IMO as now the blame is on you as previously he may have been able to get warranty service from the original vendor.
Richard
I did ask.
He is not the original buyer.
what was I suposed to do.... track back 2-3 buyers to find the original... send it to him so he can have it repaired? Anyway it was out of warranty because of the burned fuse that says that some other charger was used with it.
I had a similar thing happen but fortunately not as bad as yours. Twice now my battery has mysteriously drained completely. The last time when I tried to turn the unit on, it flashed the boot screen for a couple of seconds then poof, no more juice. When I plugged it into the USB port, nothing, no lights, no charge, no recognition from Activesync, I thought the unit was fried. I use Tmobile and got to admit they did send me a replacement fairly quickly. Before I packed up my unit I thought maybe I should plug it in using the wall charger and presto, it came on and is working fine. I have no idea what causes this but do know that if the battery is completely discharged the USB port can not over come this to put a charge on.
Same thing happened to me, kind of strange though. The charge was perhaps 70% to the best of my knowledge. I flashed it with Mr. Clean ROM and booted it up.. it came in fine into WM5, then it started the installation of the 3 progs or whatever comes with Mr. Clean.. after the second finished the unit just died *poff*. Screen blank, no responce to power buttons or any other buttons for that matter.
I've tried taking out the battery for different intervals of time, no luck. I've tried using the AC charger, no luck. No lights, sounds, telepathy or matrix ****.. it just lies there like a dummy phone.. hmm what to do. Bought it from a guy in UK (im in sweden) on eBay, don't think I will have much luck there.. even though it's brand new...
Any thouhgts?
I have had this problem - I bought a replacement battery and all is now fine. Another thread in this group states that the battery cannot charge without the OS up - so if the battery is completely discharged then it is impossible to charge through the phone. The only solution seems to be somehow to charge the battery directly - as appears to have been done earlier in this thread.
Chris
p.s. if anyone knows of another way to do it I'd be interested to hear as I'd like to revive my old battery and keep it as a spare
Hello everyone!
Lately I installed Molski's ROM (3.0.0.0) and it worked 2 days without any problems. I had to recharge the battery. I used usb to charge Wizard as I sometimes do without any problems. Wizard was On up to 30% battery, After that I switch it off to recharge it through the whole night. Led indicator was orange. In the morning there was no greed led indicator. Computer was still working correctly. I was trying to switch the Wizard on but I can't!! It can't be switch on?? Why?
I have tried several different methods to switch it on. I also checked the usb cable and it is working..
Do you have any suggestions what happened? What is wrong with Wizard??
Daniel
I think you have an empty battery now. I don't know how it happened, but you can't charge an empty battery through USB. Try using the wall-charger. When it doesn't turn on immediately try again in a few hours (keep the charger attached).
me too! using the molski rom..
My wizard is now dead. cannot flash/recharge or boot.
I tried the usb lead 'jumpstart' trick and leaving it plugged in overnight.
the battery seems fine (with a voltmeter)
any ideas?
No RGB screen?
yup, nothing. nada.
my current theory is that the battery completely discharged, now it won't turn on and charge. I tried the 'usb' hotwire trick, and saw a glint of hope(screen came on for a brief moment), but it still won't power on. I've ordered a battery and desktop charger and i'll see if that works.
is it possible that the molski rom somehow disabled the auto-off at low battery feature. That would explain things. the wizard is supposed to refuse to turn on before it hits 0%.
recharge the battery on other wizard
let your wizard in Bootloader mode:
[Camera] + [Soft reset]
plug usb then start the original update
it work in sha'a allah
declared dead. tried a new fully charged battery, plus the old battery charged in a desktop charger. doesn't boot or enter bootloader and cannot be hardreset.
the only glimmer of life is that the backlight and power light flicker when the battery is _removed_, but only if you press the power button before removal.
strange considering it was working fine. i guess it's a brick.
wanna sell me your brick for $10?
i will buy your brick for $15
shogunmark said:
i will buy your brick for $15
Click to expand...
Click to collapse
okay i'll give you $20 for ur brick.
hiimcliff said:
okay i'll give you $20 for ur brick.
Click to expand...
Click to collapse
How can you be so cruel? the guy just lost his friend!!!
I will buy your brick for 30$
unfortunately it's a brick full of my personal information!
alexjlee said:
unfortunately it's a brick full of my personal information!
Click to expand...
Click to collapse
its cool. if its a brick you won't have to worry. the parts are still good though. pm me if you wish to sell.
dead wizard
About 3 weeks ago my wizard did exactly the same, tried new batteries, different chargers etc. Nothing. Best I got was as described above was the occaisional flash of the screen.
Fortunately for me the wizard was about 14 months old and I thought was out of warranty. T-mobile (UK) were helpful enough but wouldn't take the phone but gave me the contact for HTC Europe as the phone has a 2 year warranty (in the UK). Took a little effort to get through to them but they repaired phone (replaced mainboard) and returned. Yippee for me! All I can suggest is that you see if HTC have a local office to you and speak to them.
Note - I didn't have any homecooked ROM! Just the usual updates.
Mine died (slipped into a coma?) on Friday, couldn't force it to startup using any of the standard methods - took it into the O2 shop, and they took it in the back, and made it restart. I think they tried a bunch of different chargers, but they weren't at all surprised to deal with it, and i got the impression it's not an unusual task.
Hello,
I know that there have been previous discussions on battery problems, but after doing my best to read through, I'm still a bit unsure and wasn't able to find an exact solution nor an identical match to my problem.
My problem is that recently my XDA Exec has gone from lasting around 6 or 7 hours to less than 20 minutes when using GPRS on lowest backlight and no sound.
When it goes off, the battery meter still has aroubd 95% left showing so it is really quite puzzling. What happens is that after around 20 minutes, the LCD just fades away into black and the device completely dies, no sign of life.
Trying to turn it on or reset it both result in a soft reset, and the device comes up to the O2 Logo fine, loads for a few seconds, gets to the WM logo screen and then the LCD fades away and it dies again.
The only solution is to connect it up to the power, after which it then works fine while powered, indicating some sort of power or battery problem. When plugged back in, the battery meter is still at around 90% or so and goes all he way back up to 100%.
Does anyone have any ideas as to what might be the problem and what might be a good solution? Would buying a new battery help (although the battery meter does indicate the battery is still nearly full and estimates around 6 hours usage)? Do I need to send it in for repair?
Thanks very much in advance, any advice or help would be greatly appreciated
Quboid
You should wait for the experts to help but from my intuition it really sounds like a battery problem. Lithium batteries can act very strangely if they are faulty. If nothing else works you may want to try and get a new one. Better than throwing the device in my opinion.
I don't know that I'd count myself with the "experts," but my similar problem was solved by getting a new battery. Mine too would "fade" off and then only come back on when it was plugged in. And the "fade" happened at around 70% power, so by all appearances it should have had much more time left. This was a battery that was about 15 months old, but with quite a bit of daily usage.
Go for the new battery.
Welcome to about 10 months ago when this happened to almost everybody. Get a new battery, problem solved.
Thanks for the replies,
I guess I was just surprised it might be the battery itself that's dieing, seeing as the fact it still shows charge and that it doesn't get heavy usage, only a few times per month and it's only just gone a year and furthermore, compared to my old Pocket PC which had a lot more usage and still is working fine seven years later.
Am I right in thinking that this is what I need to purchase? Wouldn't want to get the wrong thing
Thanks again for the help
Quboid said:
Am I right in thinking that this is what I need to purchase? Wouldn't want to get the wrong thing
Click to expand...
Click to collapse
That's the one!
Right, i have looked at most of these battery problems and my issue is the same as Quboid so, of I toddle off and purchase a new battery and guess what..!! Still the same, the damm thing shuts down with around 85% full charge.
What I cannot accept is the fact that this problem suddenly appears after no battery issues for the 12 months of owning the unit, you would have thought if the battery was going belly up that it would gradually happen but no...it just happens..!!, now is it that the new battery is dead...not so sure becasue at the place i work there are several universals around amd i have tried different batteries and still the same problem...
Could it be something to do with the unerversal thinking the battery is dead or is it reading a false level of charge...do you need to hard reset when adding a new battery..??
This is getting me down, after months of no problems there is nothing worse than a dead machine after 20 minutes of a full charge.
on ebay you can find batteries that could be docked into a sort of charger and charge without the use of the fone.
are these any good?
It depends on the type of the battery. If you just take your phone to the shop where you bought it, and have them give you a new battery, you'll be fine.
The original batteries only last about 6-10 months, and then they will need replacing.
Thats what i have, a new battery from the suppliers...
I've got the same problem.
My XDA dies after about ten minute's use with a full battery. I have purchased a new battery and it still dies.
I've reinstalled the ROM -- which is the standard latest O2 ROM.
I've tried it on the O2 setup, and the non-O2 setup.
I'm running nothing extra software wise -- even completely clean it dies.
I wanted to keep it running until the Omni or I-Mate Ultimate 7150 comes out, so this is really a pain.
Any other suggestions gratefully received.
hmm
theambler said:
I've got the same problem.
My XDA dies after about ten minute's use with a full battery. I have purchased a new battery and it still dies.
I've reinstalled the ROM -- which is the standard latest O2 ROM.
I've tried it on the O2 setup, and the non-O2 setup.
I'm running nothing extra software wise -- even completely clean it dies.
I wanted to keep it running until the Omni or I-Mate Ultimate 7150 comes out, so this is really a pain.
Any other suggestions gratefully received.
Click to expand...
Click to collapse
My oh My,..
i got the same exact problem, i bought two new betteries one of them is 3150mAh
downgraded to O2 rom official, and still dies at 85%
i was thinking about getting a desktop charger. till i noticed something..
when you charge your handset it charges up 100% but the charger indicator light remains on orange. (and says charging on the soft version)
it should turn green when its full, now shouldnt it.
leaving the phone to charge till the light turns green and ignoring the software reader could charge the battery, (it would still die at 85% thought)
weird problem.. i am sure now that it is a handset problem, because both the battery and the OS (rom) were changed, and still with same results.
can anyone think of something we can try?
...
come on ppl.. think.. lols
i heva that problem to!!
hi thare i have the that problem to any way to fix it ?
I have the similar problem, except it dies at cca. 30% capacity.
As I can see there are a lot of users with this problem on this device.
I am new to this device, I've been using Wizard till now and just recently bought the Universal that is over a year old.
This battery problem really iritates me.
If ANYONE has a solution to this problem that will actually work I beg him to share it with us that are new to this device.
Well, this seems to be a problem that cannot be answered, as i mentioned before, my unit is a M5000, standard issue without any rom upgrades, new battery from from the Orange shop yet it still fails at even 95%. Gonna try a hard reset because I am sure it is a software issue, i did read somewere that the machine "thinks" it is fully charged/discharged and when you put a new battery in you need to do a re set to position the unit to basic state.
Lets see what happens.
My battery problem solved
Short time ago I suffered likewise problems with my MDA pro. After reading all the comments I decided to go for a new battery from handit. With this installed the problems even worsened, regardless which charger, or cable, or combination thereof, I used. So I swallowed my avarice and bought a new battery from T-Mobile, assured that this is the one they deliver with their phones, and now everything works fine!
It seems that there are slight differences between the batteries from diefferent manufacturers, and the pro might misinterpret the signals from the battery's electronics.
By the way - have you noticed the little red slider adjacent to the baterry with which it is fixed into the housing? If you do not put it into the 'lock' position the connection between the device and the battery becomes unreliable. It may well be that a heating-up of the battery while being charged disconnects it from its contacts!
Its a well known problem, after 9-10 months the battery cannot handle high powered functions causing it to turn off.
Get a new battery and you'll be sorted.
a 3150mah from ebay is only about £10-£15 but will make your universal a bit fatter. (they provide the larger cover for the back)
Yeh fine,,,all well an good if you do not use a jasjar car tray or holder as such, the soddin thing will not fit in it with this slug on its back
Qtek 9000 battery probs
Hi everybody
All I can say is I'm having det excact same problems with a Qtek 9000. Have tried changing batteries. Have even bought an extra extended battery (3150 mAh), and all for nothing. It worked for a brief periode. But now I'm back to square one again. The darn thing dies on me, even though the battery is charged (70-90%).
Have had a dialog with Qtek, but they claim they havn't heard of the problem before
Have been trying to figure out what the problem is..... and have tried to solve it with various workarounds.... Situation right now... Im pretty sure it's the battery on the systemboard that's causing the problems.
It kind of makes sense IMO... if you have a PC with a faulty battery nothing will work.
I'm going to see if I can get the battery changed (still have warranty). Keep your fingers crossed. I'll get back to you all if it fixes my problems.
I bought a second hand HD2, however it arrived with a third-party chinese battery. I contacted the seller who apologised and said that battery was a replacement because the original didn't hold a good charge, and he would send the original through the post. The battery however was fully charged so I flashed all the neccessary files and installed NAND Android (my reason for buying it in the first place), however today - the same day it arrived - I noticed that the orange charge light was going off, usually when the phone screen went off. This necessitated plugging the USB lead back in again, and within sometimes less than a minute the same problem would occur. I have checked the battery prongs, reset the the phone, changed USB settings etc and the problem persists.
Just wondered of I should be worried...I am unable to find an identical problem to this on the forums so I'm assuming it's not a ROM issue. I am currently using the Desire port from DFT.
Would a cheap Chinese battery demonstrate this sort of problem?
The seller says he never had an issue of charging the phone.
My next resort is to flash Windows Mobile back on, but I'm at work and a bit anxious so was hoping for someone with some experience to reassure me!
All USB syncing etc works fine...it is literally just charging that's the issue.
Maybe it's your USB that's faulty. I had a faulty usb that would go on and off sometimes too. However I don't see why the battery would affect the LED light, as the battery has to be connected to the phone for it to stay on, and so the battery can't be losing it's connection with the phone randomly, so it's either your usb cord, or the port.
Word of advice, don't let your phone lose power cuz of the faulty charging. I assume you know that MAGLDR doesn't let you charge the phone while off, so a dead battery in our case, is a dead phone. Happened to me once cuz of my usb, luckily there was still a small amount of charge left after i took the battery out and placed it back in.
It's definitely not the cable as I've used an official HTC charger with it which does exactly the same thing. I've also tried with a Samsung MicroUSB charger from my Galaxy S
Maybe it's the usb port then... That's the worst case scenario because you'd have to get the whole motherboard replaced...
However if in winmo you don't experience the problems, then it was just some software problems, so try a different radio and build, and see if they work.
Edit:
Or maybe it's the LED that's faulty. (never heard of such a situation but anything is possible) >.>
Does it still charge even if the LED is not orange/on?
Thing is though I can pretty much get it to stay charging if I don't let it lock and the screen go off? Could this still be a problem with the USB port? I'm getting worried now as I don't like the hassle of sending things back through eBay. I'm wondering if the seller bought a spare battery thinking it was just a battery problem and isn't telling the whole story. Foolishly I didn't test the device with Windows Mobile, I just went straight into flashing as I had put Android on my friend's HD2 the other day in exactly the same way...his is even an ex Virgin Mobile phone like this one. Needless to say, he is having no charging issues.
Dude dont worry , the problem is the battery ! i got two chinese battery ones and both cant charge with the phone, i have to use eksternal charger Dont worry the red and orange led flashes constantly when i try to charge it
Just buy a cheap charger from ebay , and buy a oem htc hd2 battery
Hi thanks for your reply. Mine doesn't flash red and orange though: the orange light comes on as normal and the phone reports it as charging, but after a while (seems to be when the phone goes to standby most of the time) the orange light turns off and the charging symbol disappears. If I unplug and replug again the light comes back on for a period. I've not tested thoroughly but I THINK it will stay charging when I leave the phone out of standby with the screen set to stay on for 30 minutes. I really HOPE it's a battery issue but it sounds slightly different to yours as mine does at least charge to a degree. I'm worried there's a blown capacitor somewhere on the logic board that's making the phone charge malfunction but obviously there's no way of testing until I get a new battery.
It concerns me that the seller said he had no charging problems...he must have been able to charge it somehow as the battery was full when it arrived...could I have burnt something out when flashing?!
Mine do charge to about 50 % and then it stops
Im 100 % sure its the battery becouse the battery has a circuitboard inside of it, and thats often messed up considering its made cheap in china . But test it with your friends hd2 original battery You can 2 see if the wet indicatior has been activated
the " white " paper next to the battery poles should be white and not pink, alltso where the skrewholes of the phone that should allso be white just to make sure your phone is not waterdamaget
I don't think flashing could have burnt something out. Overclocking and generating a lot of heat can burn something out though.
Didn't you receive the stock battery? Why not try it with that, and if the problem stilll persists then it might not be the battery. Either way, it will help you to test out the phone with a stock battery.
I tried it again after a few hours and it charged for a fair while before the light went off again.
I don't have the original battery as the seller has yet to mail it to me.
Does anyone else think it's worth me trying out a stock Windows Mobile ROM to see if it works? Might be that Android ROMs are less forgiving of cheap batteries with dodgy circuitry..
UPDATE
Ok so I've flashed Windows Mobile onto the device and wiped Magldr. The phone now alternates between a green and an amber light on the charging indicator. Looks like Windows Mobile won't charge it at all!
Does anyone know what this means?
I've checked for water damage in the areas mentioned and there is no sign.
Well your best bet is to send it in for repairs. But I'd suggest you test the phone out first with a stock battery.
Well I Only bought the phone yesterday so I certainly won't be paying for any repairs.
Got a replacement battery today - a genuine HTC one.
Plugged in, switched on....flashing between amber and green
I have a nagging suspicion this is going to be an eBay refund nightmare.
have you checked that the pins on the phone is not bendt? pins where battery poles connect to phone
problem solved? fingers crossed
OK so as a last resort I flashed radio 2.15 to the device. Seems that this has completely fixed the problem as without even restoring the phone is now charging properly. It seems that a corrupted radio flash had affected the charge somehow....at least I hope so.
The same problem has not come back again today at all.
Might be worth throwing this solution in a problems and solutions section as I haven't found any reference to it on the net and it might fix things for others panicking over their handsets.
That's nice.
Good for you, since it's a hassle to deal with sending back the device and shizz like that.
was just searching is anyone had a similar problem like me. to the OP yours sounds like my problem.
Had these fake OEM batteries for a while now. Until recently they have been charging ang turning off in 1 1/2 minutes. put a genuine OEM battery in and the problem is gone.
My solution was OEM can charge thru phone but fakes cant, use fakes as backup and charge it thru a desktop charger. goodluck
Hi All,
I bought a replacement battery for my SG2 for longer battery life from M0bilefun, I inserted the new battery into the phone and left it to charge as their was no power but i got this grey battery icon come up every 10-20sec with a circle in the middle, thought it needed a full charge so i left it over night on charge but still the battery has no power, so thinking it must be a bad batch or something i have replaced it back with my genuine battery which I had around 70% charge left and now the exact same issue, the phone refuses to start and this stupid grey icon and that's all i get
the charger is plugged into the mains on a Belkin Pro AV surge protector extension cable.
any help or advice would be appreciated?
PS: reading the battery packaging it only comes with 6 month warranty which cannot be good otherwise it would have come with longer warranty - i wish i had known that.
a5ian300zx
Forgot to mention that I have tried doing a Hard Reset (power+volume down + home button) but nothing happens at all.
also i have the latest version of CriskeloRom v14 installed
a5ian300zx
this is weird hot swapping the batteries around with the Andida and samsung it seem to work now with the andida battery, I will give it a full charge and see how it goes.
a5ian300zx
Please tell us how you fix it, for those people having the same issue
Hi,
I just swapped the battery over to the samsung one and then back to the Andida and seems to have resolved itself, but the battery life seems to decrease quite fast i fully charged it at 10am today and im one 55% with only one 5 min call made to day at 3g/data off, wifi on. and i used the wifi for around 20min.
but i will see in the next week or so, to let it wear in after few charges.
a5ian300zx
Dear a5ian300zx, my phone diad and it did not worked at all after installing Andida Battery 2000mAh. Ckeckout my new thread
http://forum.xda-developers.com/showthread.php?p=17076763
I took my phone to Samsung Service Center. The technician told me that the battery sensor indicator chip is damaged in the main-board and need to be replaced.
you might have the same problem. **** Andida Company, we have to sue them for dmanging our SGS2