imate jasjar: locked after rom upgrade - JASJAR, XDA Exec, MDA Pro General

hi.
i have imate jasjar with italian language.
i have downloaded new firmware from imate site, connected my jasjar to my pc and launched upgrade procedure.
The upgrade procedure will start and then after that my jasjar will reboot by the upgrade utility.
But my jasjar will not power on.
I have wait 15 minutes.
Than i have disconected from pc and reset, hard reset my jasjar.
I removed battery and reinserted...but mothing.
When i power on the jasjar it write on the screen: SERIAL....V. 1.00...
wHEN I do an hard reset, on the screen menu i try to type "x" to hard reset...but nothing.
What can i do ? Thanks at all.

The device is now in bootloader mode. Just reinstall the ROM all over again. Try on a different PC if it doesn't work on yours.

Related

ATT Siemens SX56 and Stuck updating Rom

I have a Siemens SX56 a usb cable and SD card and while using the Special Edition Rom heres what happened:
When updating the ROM (it said updating on the PC and on the phone), I received an error message on the PC. It told me to unlplug the device, do a reset and try again. I tried that, but the seimens sx56 still displayed the screen that says upating ROM. Reseting does not seem to work.
I am using the usb cradle that came with the phone. I used active sync to
connect to my PC. Yes, All the phone says now is "upgrading, will take about 5 minutes. I tried flashing the ROM last night. The phone has been in this state for at least 15+ hours. Doing a hard reset does nothing. All the pc said was "an error occured while trying to upgrade, please remove the device from the power source, reset the device and try again."
Now the phone won't connect to the pc via active sync.
Thanks.
search thru the forum, you may find something!
If not , let other people fix it for you!
Did you manage to fixed your phone? Got the same problem.
You should download xdatools, program your sd card with the rom, then put the sd card in the pda and push reset while holding down the power button, push the action button when prompted, this will program your phone, as long as you dont have one of the akward bootloaders you should end up with a working phone after a hard reset.

Stuck at the last reset after Update my O2mini ROM

I have followed the below step to upgrade my ROM directly to BigStorage.
I am using the ftp://forum.xda-developers.com/Magician/BigStorage_ROMs/WWE_1.12.rar
1. backup the ROM to SD
2. ntwr the WWE_1.12.rar to SD
3. Callup Bootloader and wait fro 100%
After that.....does anyone can tell me what should I do.
I have tried to soft-reset the JAM with SD....I prompt for "Press On/Off button to Flash" again.
I have tried to soft-reset the JAM without SD and with USB..... it prompt for "USB"
I have tried to soft-reset the JAM without SD and with Serial..... it prompt for "Serial"
Pleaes let me know...or should I do a hard-reset?
But please let me knwo how to "hard-reset"
I have no idea on this.
Did you get the Checksum failed message? If you did, just do a hard reset (remove the SD first). You can do a hard reset by pressing the Power button while pressing the Soft Reset.
If you didn't ge the Checksum error and you're getting the "Press Power Button to Flash" it means that the ROM was not written properly.
You probably have a corrupt ROM on the SD. Try copying the ROM to the SD again.
Thx kta......
You are right. I have "ADDED" the 416 bytes to the ROM rather than replace it..
Now I am working fine except the O2 connect.
I have installed the O2 connect but while i run it. It prompt the O2 connect is only for O2 device.....
But..mine is exactly a O2 mini. Any idea?
mikokwan said:
Thx kta......
You are right. I have "ADDED" the 416 bytes to the ROM rather than replace it..
Now I am working fine except the O2 connect.
I have installed the O2 connect but while i run it. It prompt the O2 connect is only for O2 device.....
But..mine is exactly a O2 mini. Any idea?
Click to expand...
Click to collapse
What is your splashscreen, is it still O2? I think as you flash your O2 using ROM from manufacturer, your O2 mini is now not an exactly O2 mini

Startup problems with a M600 need help

I have a Prophet (M600) G4 with the last HTC ROM and recently radio upgrade and everything works fine till in installed Resco keyboard and had to soft reset the device. Till then the device comes up normally with the Qtek welcome screen but during the next step to “the windows screen ??” appears a white screen and nothing happened after it. Strange enough hardreset don’t work and its impossible to enter the bootloader. Moving the battery and reset several times has no results. Try to flash it again but impossible because I have no connection to PC. Can someone help me please??
Help! My Dopod D810 dead, can only run bootloader
All ROM I tried are not accepted by bootloader. What can i do?
fuego_nl said:
I have a Prophet (M600) G4 with the last HTC ROM and recently radio upgrade and everything works fine till in installed Resco keyboard and had to soft reset the device. Till then the device comes up normally with the Qtek welcome screen but during the next step to “the windows screen ??” appears a white screen and nothing happened after it. Strange enough hardreset don’t work and its impossible to enter the bootloader. Moving the battery and reset several times has no results. Try to flash it again but impossible because I have no connection to PC. Can someone help me please??
Click to expand...
Click to collapse
qtek s200- prophet problem please help
After reset work but screen is blank with green and blue lines,can some body help

iMate JAMin Boot problems!!

hey guys, over the past few days ive had battery problems with my iMate JAMin, i got a new battery, insert it, and power on my device, now, rather than loading up the iMate image, it goes to the tri-color boot screen, i've tried a Soft and Hard reset, no luck , any one willing to try and help solve this problem, please email or PM: [email protected]
Will installing a new rom fix this problem?
Aidenkidd.
From the wiki:
wiki said:
If during an upgrade your Prophet fails to start properly or can only enter bootloader follow this:
Recovery
Download and install the latest version of ActiveSync (Google for it)
Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from
here (any part one) or
here
Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
Plug the Prophet in via USB
Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder
Disconnect the Prophet, and then re-enable the connect through USB.
Your Prophet should now work!
Click to expand...
Click to collapse
I wrote it any way, but since no one reads it I may as well post it here.

qtek 9000 doesn't turn on

first i'm sorry for my english i try to explain my problem in best language
i have a qtek 9000 and one hour ago i flashed my phone with Ranju_v76_WM61_19209_19209_1_0_2.exe (sticky topic) and this operation finish correctly.I used wm6 for abouy 5 minutes. suddendly my ppc turn off and doesn't power up but if i press keys for hard reset it power up with press 0 to restore factory or X...
If i press 0 my ppc turn down and doesn't power up.
If i try to connect in my pc windows xp write "Periferica non riconosciuta".
how can i do?
Hi Alex, well, have you tried to enter in bootloader mode and re-flash with your prior rom?
Also, you might want to try a full hard reset to your device first.
Let me know if you need italian directions for this.
battery
Also check if your battery is old or try getting a new one and charge it and boot it up.
Mine was some what of the same problem, until i got a new battery and now it's working.
My XDA with the ranju rom did this over the weekend. Was working fine for weeks then turn it on after 2 days non use and its dead. Could the rom have an issue?
All sorted now via bootloader.

Categories

Resources