Stuck at the last reset after Update my O2mini ROM - JAM, MDA Compact, S100 General

I have followed the below step to upgrade my ROM directly to BigStorage.
I am using the ftp://forum.xda-developers.com/Magician/BigStorage_ROMs/WWE_1.12.rar
1. backup the ROM to SD
2. ntwr the WWE_1.12.rar to SD
3. Callup Bootloader and wait fro 100%
After that.....does anyone can tell me what should I do.
I have tried to soft-reset the JAM with SD....I prompt for "Press On/Off button to Flash" again.
I have tried to soft-reset the JAM without SD and with USB..... it prompt for "USB"
I have tried to soft-reset the JAM without SD and with Serial..... it prompt for "Serial"
Pleaes let me know...or should I do a hard-reset?
But please let me knwo how to "hard-reset"
I have no idea on this.

Did you get the Checksum failed message? If you did, just do a hard reset (remove the SD first). You can do a hard reset by pressing the Power button while pressing the Soft Reset.
If you didn't ge the Checksum error and you're getting the "Press Power Button to Flash" it means that the ROM was not written properly.
You probably have a corrupt ROM on the SD. Try copying the ROM to the SD again.

Thx kta......
You are right. I have "ADDED" the 416 bytes to the ROM rather than replace it..
Now I am working fine except the O2 connect.
I have installed the O2 connect but while i run it. It prompt the O2 connect is only for O2 device.....
But..mine is exactly a O2 mini. Any idea?

mikokwan said:
Thx kta......
You are right. I have "ADDED" the 416 bytes to the ROM rather than replace it..
Now I am working fine except the O2 connect.
I have installed the O2 connect but while i run it. It prompt the O2 connect is only for O2 device.....
But..mine is exactly a O2 mini. Any idea?
Click to expand...
Click to collapse
What is your splashscreen, is it still O2? I think as you flash your O2 using ROM from manufacturer, your O2 mini is now not an exactly O2 mini

Related

Mda - death after Update! HELP!!

I got trouble - I tell you....
Yesterday, I wanted to update my T-mobile MDA from winmobile 2002 to 2003. I was using "Lumpistefans" -Romkitchen (xda.weblink.net). I choose the rom to be coocked as an "installer exe".
When I performed the update, everything worked fine - for about 30 secs....then brakedown
This message accoured "Can not open COM/USB port...."
from this time on, my mda seems to be toasted!! I can't switch it on , softreset won't work - and after an hardreset the display only shows some black stripes and two blank squares at the top half.
I don't need to mention, that Activesync isn't recognising the mda anymore - saying "uknown usb device - can't connect"
I don't think the Bootloader is working still either - by pressing the on/off button, the bootloader should be activated ..or??!? I never tried that before.
I read the thread "rom flashing is dangerous" but didn't get any helpfull info on my case.
I need Help...getting quiet despered!!
THANKS for alls Help , Hints and comments!!!!!
ciao
mark
here is how you enter the bootloader
http://xda-developers.com/bootloader/
ok thanks - the bootloader is still working ... can i now just flash it with a rom using my sd card?
yes just plug in the sdcard of min 64MB into your sdcard writer/reader and use xdatools to flash the nbf or nb1 file to the card
and put in the sdcard and go back into the bootloader

HTC Polaris/Cruise (XDA Orbit 2) bricked.

Hi everyone,
I recently received an XDA Orbit 2, literally, charged it for 2 hours, and when it was full charged, I started using it, I had it for about 2 months now, and recently I changed my home Internet connection to wireless (It's a B & G connection) so my laptop connects fine, and when I tried to connect my XDA Orbit 2, it connected and then soft-reset itself, and now it just loads the O2 screen, then Windows Mobile screen with the volume controller and I can't do anything else so here's what I have tried so far:
- Soft reset
- Removed battery and SIM
- Since I can't access phone's menu at all, I tried to Hard Reset method by holding the 2 soft key, reset, and the power button - So I get the warning that everything will be lost and to press 'Send' to continue, so I press the green key, and soft resets and goes back to the same situation again.
- The latest thing I tried is to load the Hard-SPL into the SDCard which has been formatted to FAT32, so loaded the POLAIMG.nbh into the root. and loaded the phone into BootLoader mode (Camera and reset buttons). It loads the memory card and just says 'Loading ... ' I left it for about an hour, until the battery died completely (I'm sure it's not supposed to take that long). And still the same problem.
I'm not sure if this phone is now bricked, can anyone help me plesae. I really need this to start working again, I don't have any info. on it. (Everything was sync. previously).
Kind regards,
Since you havent really messed with SPL, i would say to take it back, since its still into warranty.
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
htctytnowner said:
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
Click to expand...
Click to collapse
I assume just boots into bootloader and then stays there?
If yes you culd try searching out a thread on MTTY and recovery from boot loader but I dont know how well that would work on polaris as I have not tried it yet.
HTH
Leon
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
htctytnowner said:
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
Click to expand...
Click to collapse
Only in the ELF forum
Here:
I'm pretty sure you can download MTTY from here and read through how to use it.
http://forum.xda-developers.com/showthread.php?t=347700
Also it is worth checking the wiki and searching
http://forum.xda-developers.com/showpost.php?p=2054848&postcount=38
Please do some research! I have not done this before and I have no idea what the commands do!!!
pqillu said:
You can try this:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
THX to christonge
Good luck.
PQillu
Click to expand...
Click to collapse
Please Heeelp!
I wa installing a rom from todopdas.es an my Polaris doesn´t pass from the screen where´s said "smart mobility", and R1.58.21.23 G 25.65.30.04H D 1.52.00.00, please what I can do?
You need to do Hard Reset, all information will be wiped off. To do hard reset, hold down the:
1.Press and hold the GPS/MESSAGING and INTERNET EXPLORER
buttons, and at the same time, use the stylus to press the RESET
button at the bottom of your device.
2. Release the RESET button, but
continue pressing the GPS/
MESSAGING and INTERNET
EXPLORER buttons until you
see this message on the
screen:
This operation will delete
all your personal data,
and reset all settings
to manufacturer default.
Press Send to restore
manufacturer default, or
press other keys to cancel.
3. Release the buttons, and then press SEND on your device to perform
the hard reset, or press any other button to cancel the reset.
Good luck.
Hi,
I'm using an HTC TC POLARIS100. Today I upgraded my ROM and SPL successfuly. If you're still in trouble and believe the same process will help, I will let you know the process followed.
GUY

Newbie: cannot install Hard SPL for love nor money help!!!

Before anyone ask's I have read all the posts regarding installing the Hard SPL but still have the same problem.
When I connect through Vista 32 via WMDC it recognizes my device fine, I then follow the steps in the tutorials but as soon as I press the button to update the ROM image it goes into the 3 colour screen and then into the updating ROM progress bar were it sits at 0% for ever.
My WMDC has disconnected at this stage and then I get a screen saying communication error which is obvious as WMDC has disconnected.
Is this a WMDC issue/ Vista or am I missing something
I then have to soft reset and it just re boots into my standard ROM.
Any advice woiuld be greatly appreciated
hello
1) connect your polaris to PC
2) run update utility
3) when you see 3 color screen unplug USB and replug it immediately
4) your SPL flash may start
5) when flash end correctely your polaris reboot
6) Flash any ROM you want
Thanks for the quick reply.
Tried doing exactly as you have stated.
Unplug and reconnect in the 3 colour bar screen, after which it goes into the updating screen and sits at 0% for ages until communication error comes up.
My WMDC has disconnected and does not reconnect.
I'm at my wits end!!
Do it from MicroSD, before format it in FAT 32, after rename the file .nbh in POLAIMG.nbh e copy in your microSD, put microSD in Polaris e put it in bootloader ( photo + softreset ) you will see something like IPL, bootloader, SPLASH1, SPLASH2, gsm & OS, press POWER button and wait, it might be long,
never put off microSD, when it finishes soft reset, in the same way you can flash any ROM, always format microSD before.
Do it from MicroSD, before format it in FAT 32, after rename the file .nbh in POLAIMG.nbh e copy in your microSD, put microSD in Polaris e put it in bootloader ( photo + softreset ) you will see something like IPL, bootloader, SPLASH1, SPLASH2, gsm & OS, press POWER button and wait, it might be long,
never put off microSD, when it finishes soft reset, in the same way you can flash any ROM, always format microSD before.
I think hard-spl can not be installed with sdcard method!
Why not ??? With Trinity you can do it.
cheers guy's for the feedback ,but not sure about the SD method unless someone can confirm it works for Orbit 2/ Cruise.
Somebody out there must have had the same issue as me regards this....what did you do to resolve.
Cheers
batista70 said:
Why not ??? With Trinity you can do it.
Click to expand...
Click to collapse
But this is not Trinity...Try it...
I know You can flash polaris if you use jumpspl (this is used by hard-spl flash) or hard-spl (this is used by os and radio flash).
But if you have original spl on you pda, and you want to flash with sd card, you will not use nor jumpspl neither hard-spl.
mikee5402 said:
cheers guy's for the feedback ,but not sure about the SD method unless someone can confirm it works for Orbit 2/ Cruise.
Somebody out there must have had the same issue as me regards this....what did you do to resolve.
Cheers
Click to expand...
Click to collapse
hi there.
try to hard spl with your sd card not in the device.
go in to bootloader mode (BL mode - by pressing down the Camera button, then using the stylus, press and hold the RESET button at the bottom of the phone and release when tricolor screen appears),
now connect the device to your pc (it should show usb in the white part)
flash what you may... hard spl first, oli's recomended by me.
ItayE,
Did you try the hard-spl flash with sd method? Does it work?
I didn't read it was Vista compliant so I ran it from a windows XP SP2 machine with Active Sync 4.5.
I did mine by taking out the SIM card and the SD Card then resettting and running the HardSPL.
HTH
Leon
Cheers for the advice guys I have managed to do it.
I used the Hard-SPL-V2 first which worked fine then I flashed to one of A.Serg roms, very nice and quick it is too.
However my reception bars are down to 2 from 4 that I previously had, although the reception seems ok.
Sim: O2 UK
Rom: 1.52.ASerg.4 WWE
The radio version I have is: 1.58.25.14
Now this is were I am confused.
Can I flash the radio Rom without affecting the o/s Rom, I have downloaded a couple of radio rom versions but not sure if you do it the same way as I am scared of over writing something.
Also could anybody advise if they are in UK on O2 which version gives best reception.
Any further advice much appreciated.

HTC hangs in bootloader after attempt to flash rom

Hi!
I have a HTC P3300.
I bought a 4Gb SDHC card, and it won't work. I read at the forum that I would need a different rom, so I downloaded "Artemis_Touch_4.02_Full_with_no_cube", which would have sdhc-support.
Then I executed "STEP 1 - activesync then uspl cid unlocking.bat", that finished ok, and then "STEP 2 - activesync then flash artemis touch rom.bat", which stopped with an error 302.
After a restart all that came up was the boot loader. I then tried to flash the original rom (HTC WM6 Dutch) from the computer, but that ended also in an error.
I tried the SD upgrade (rename .nbh file to ARTEIMG.nbh, put it on a formatted sd-card and load it in my phone), and it finished without errors, saying I should press any key.
After pressing a key, the bootloader popped up again.... :S
Can anyone help me? I have been searching the forum and trying to get my phone to work since 21:00 and I haven't got any progress at all!
well sorry for that
did you tried to make hard reset?
and once i had a completely dead artemis.. no sign of life..but it fixed by the following..(and maybe this may help you cuz the flasheng goes not like usual)
while your mobile is off.. press the record botton and the camera and it should starts with usual sd card flashing.
for me this what happens.
the setup was in three phases as i saw... and it took about 30 mins .
maybe it will works for you
I also tried a hard reset, wouldn't work.
I pressed and hold the camerabutton, but nothing happend...
Maybe the battery is empty, so I pressed and hold the camera button while plugging in the usb-cable.
It started the SD-upgrade, and is still busy.
The update ended with a "press any key to continue".
But when I pressed a key, the boot loader popped up :S
When I tried to flash another rom (NLD-FINAL), an error occurred (I believe it was error 270, not sure).
But then the normal startup screen appeared!
I don't know how, but the problem seems to be fixed!
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
As you can see in my previous post, I managed to flash the original rom.
I'm gonna try to upload an other rom some other time...
And with a patch I got the SDHC working too!
Thnx for your help!
y_bother said:
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
Click to expand...
Click to collapse
Hey, thanks a lot, I tought, my HTC-Cruise is ready for sending to repair, but with your info, it works again. I could install the WM 6.1 again, after System hangs up while booting every time. He found USB connection on a colored sreen. Thank you very much.
Jupeli

SD Card Flashing Question!

Hello to everyone,
i have a problem with flashing.
First i had a WM2003 OS on the T-Mobile MDA. Then i tried to flash the WM2003SE with a romkitchen rom.exe over active sync.
The whole upgrade process worked well, but now it don't boots.
The booting procedure hangs on the welcome screen.
Now i am trying to flash a PPC2002 OS with SD Solution. (Because i have no activesync connection)
I have downloaded a *.nb1 rom from romkitchen and make copied it to SD with OS Image Tool.
But i don't know what to do now. When i insert the SD in the PPC it says only "The Card is not readable do you want to format it".
PLZ help!
Best regards
Andy
never heard about the bootloader saying that only a device saying it when it's booted into wm???
one way you can verify that the rom is flashed to the sdcard using the tool
the pc is no longer able to read the card
so that way you can verify that you did it correctly
Well, i did it by the same way (yesterday) ok, we can say you already have your SD card with your ROM ready for the instalation, so your put your SD car inside, then press the power button on top and press the hard reset button (you know it's down the earphones hole) it will apears the bootloader screen and the it will says press action to start or recort to exit, press the action button and it will start to donwload, it will finish saing COOLD RESET and something like that, take out your SD CARD and make a soft reset (the little hole at the other side of the hard reset) and that's it !!! i hope so jejejej let me know
thanx a lot. This worked for me!!

Categories

Resources