Related
Hi all,
Just go the xda through work, and even though i have got the new version of tom tom of their website (5.2) for ppc, when loaded and docked in my cradle, it cant sem to get the GPS to receive!?!?! anyone else had this problem?
I have an O2 XDA Exec and its working fine with the TomTom 5.2 software. I got some very useful info from http://www.pocketgps.co.uk/modules.php?name=Forums&file=viewforum&f=6 ..... basically a post on there advised setting up an outgoing com port to the BT GPS device (I used Com0) ... this is found under Start>Settings>Connections>Bluetooth>ComPorts (after you have paired the BT device of course).
In TomTom you then select "Other Bluetooth GPS" in the GPS options screen, select the Com port set previously, and away you go.
I hope this helps
I bought a 32-channel QStarz GPS receiver from eBay, cracking little thing it is. I had problems getting it going though initially - what I had to do was setup a pairing, which was a little tricky as TT didn't want to behave.
Basically, TT tries to establish a serial connection whenever I open it. As TT loaded, just before it went into the TT interface, It showed a dialog box with all my serial connections in - I think it might've been the device pairing screen, but I've not been able to find it again... What I did was pick the gps receiver's serial port device entry I'd previously set up, select it, check the box to tell TT to always connect to this device by default, and then hit enter - all before TT managed to load into the interface. It took me a couple of goes, and I'm sure there's an easier way to do this (I don't think I was even supposed to see this dialog screen ) but now it works perfectly. I don't have to establish the Bluetooth connection to the GPS receiver, TT does that (and it'll even turn the Bluetooth on and off if it's not already on for me). However, I did have to choose Other NMEA GPS from the device options, and then tweak my COM port settings (I found a scant piece of information regardingthe fact that it should be something like COM5 for incoming data and COM6 for outgoing data, you would do well to doublecheck the TomTom site's FAQs for this info). There's a couple of seconds lag whilst TT correctly detects the device and begins to latch onto GPS sats (it says "No Compatible GPS Device Detected!", and then changes to something like "No GPS Signal Detected"... And then starts picking up sats.
This is all with TT5.0, by the way.
This document will be very useful.. principal is the same for most GPS Receivers..
http://www.parrot.biz/ressources/CK3400_Help_Files/Imate JASJAR - TOMTOM Mobile 5 - 2.01.pdf
Not sure if you are trying to receive through a Bluetooth GPS receiver - if you are, this worked for me (first poston the page);
http://forum.xda-developers.com/vie...ostorder=asc&highlight=tomtom+5+gps&start=100
Thanks for your help guys, but i meat to say i am using a wired GPS the small square official Tom Tom one, hard wired in to my cradle.
I can open the software and everything, but it just says, cant find GPS, the green light flashes on my GPS, but thats all it does.
Help!
Ok, so you're using a wired receiver.. That helps to know. You should be able to choose TomTom Wired GPS or Other Wired GPS, and it should just... work. If it doesn't, choose the nearest chocie to your receiver, and go into the Advanced settings (if the option button is available) - if so, doublecheck what your COM port settings are.
Where did you buy the cradel from, I just got ripped off to the tune of £48 off ebay due to the cradle not actually passing the srl connection through, all it does is provide power for a Bluetooth GPS Receiver out of the port on the side.
I think I've heard othe rpeople saying that wired GPS receivers will not work with the Universal. Can anyone confirm this?
What you have heard is correct the mini USB on the Exec WILL NOT accept a GPS connection, you need a bluetooth device for this to work - Mike
Tony B - that sounds like the cradle i am using - jasjar or jamjar something like that!
I have put my wired GPS straight in to the side, and nothing!!
think you might have got it mate!
hi there
i am using the wired gps with mda pro tomotm car cradle
tomtom software working like i can start the tomotm and see the setting etc
now when i connect the tomtom wired gps via rj11 in cradle but i can not recieve gps signal
device says "no gps device"
please help
Regrads
Gugi
HI all!this is my first post on the forum and i am glad to be here!
the problem is i cannot connect the holux 236 to the s100 or magician.
rom version is 1.12.00WWE.I tried pocket bluetooth tools but no luck.
the gps viewer gets nothing and also the destinator pn shows that no gps is available...
please help in any way...a walkthrough would be welcome since i am a newbie with ppc...
thanks in advance and keep up the good work!!
Hi, have you had any success with any other gps reciever opr is this the first one you try?
Suppose you have tries to enter the sw program and then configure the reciever with your magician? Is this where the trouble is?
this is the first one to use.
s100 gives com 5 to the gps but still no luck with ddestinator.states that no gps is present.
maybe a bluetooth stack problem?
could use all the help i can get..............
Ive just ordered a Holux 236 from Fleabay, should be here in a few days, will post my settings if I get it working ok
is the holux 236gps mini actually compatible with the QTEK S100??????????
Hi
Switch on Bluetooth and Pair the device using pass key 0000
Then DO NOT connect the device
Enter GPS Viewer 1.5 and select (Bluetooth) COM Port 6 (may be something else on your device). Select Open GPS and you should start getting data...
Hope that helps
The whole problem is that I cannot get my Qtek 9100 to show the spp slave service. This seems to be a qtek problem because none of my other BT devices will show it either. They showed fine with my old HP 6365. :?
I am not sure in that case... I cannot remember but does it use Widcomm Stack or M$?
I'm not sure what stack they use. I don't think it's Widcomm, because my HP BT keyboard won't connect and the reason is that it says there is no Widcomm stack. Go figure.
if thats the case,how do we solve it?third party software?change bluetooth stack?and if yes how.........?and i thought it would be plug n play...
OK, I have this BT receiver, works perfectly with my mini. Have you added any bluetooth stacks in addition the default ? When you search for devices does the Bt find the Holux? Is it switched on and charged? Don't know how new you are to bluetooth devices, but bear in Mind that a brand new Bt device out of the box may take up to 30 minutes to get a fix for the first time.
no new stacks added,device is charged.
gps pairs with s100,asks if it should create a port,i reply yes and i press finish.in the bluetooth menu at the com ports i press new outgoing port and i am asked to choose a device.i select holux,press next and nothing happens....so whats the deal here?in the bluetooth serial port setup i check the outbound com port:com 5 beforehand.so please tell me what am i doing wrong this time....is there something i didnt do or something i did...?
Ok, so the pairing came up fine. Thats one thing out of the way.
Now, forget selecting outgoing or incoming ports, its completely useless, doesn't work. I have TOMTOM and have selected "Other Bluetooth Device" and selected COM5, it works fine. Could be your com port is being occupied by other bluetooth such as Activesync.
Delete all paired devices, Go to Start, Settings, Bluetooth Setting and check that "Outbound COM port: COM5" is ticked only, click OK then try pairing your Holux and try again. It does work with the mini, I promise!!
I got a 236 slim and no problem with MS BT stack.
try to connect as explained by moghisi101, it should work
WELL i did try,trust me!at what point should the orange led light up???it should first communicate with the gps viewer and then start blinking or something?cause so far the orange led has not shown its colors........is this normal or do i have a faulty gps?????????????
Hmmm sounds like a faulty unit. Ive had my 236 for a couple of days now and it worked first time with Tomtom, just selected 'Other device' and 'Com5'
Im really impressed by this unit, even gets 5-6 satellites indoors !
When you turn the unit on the orange LED should be on all the time (searching) then after about 45 secs it should start to flash indicating that it has locked onto satellites. If you arent getting any light from the orange LED it does suggest a faulty unit
HTH
Hello All,
I have today noticed a problem with my XDA Mini S following the installation of TT 5.21 - Before the software was installed the phone would pair and remain connected with my Vauxhall, factory fit, bluetooth carkit. Calls could me made and received, phonebook info would sync with no problems - all 600 entries!
Following the installation of TT5.21 the phone will now disconnect after 15-20 seconds from the carkit unless TT is running with an active route and the TT Traffic updates enabled!!!
Trying to make a call without TT running means that it only presents on the phone and does not go though to the car kit. Even with tomtom running, unless you have a route planned and TT traffic active then it will still disconnect from the carkit...
I have posted a question to tomtom technical support regarding this and will also try O2 tomorrow to see if they have seen this before...
Anybody else seen anything like this?
Andy. :?
Silly question - is the bluetooth on constantly on the Mini S? If not you need to do this.
TomTom switches bluetooth on automatically if it isn't on already, if you have a BT receiver selected, which I assume you have.
Its not a silly question - I thought that this was the problem to start with but even with Tomtom running and talking to the GPS receiver, it still disconnects from the car kit unless tomtom traffic is active and you have an active route... :? :?
No updates from TT Support yet :roll: - i'll post when I receive something.
Tomtom support came back today with the following response - reading it, it is obvious that they have not understood the problem...I have written back to them pointing out the fact that it also disconnects even when Tomtom isn't running - Only way to get it to work is to have tomtom traffic running - maybe something in that... ;-)
Since we do not support the usage of third-party carkits (Bluetooth or wired/serial), we are only able to offer a technical theory as to your problem.
As your carkit is connected with a (virtual) Bluetooth serial connection, there is most likely an internal conflict with regards to the serial connection. PDA's support multiple Bluetooth profiles (methods of connecting), but typically bind the serial port to one device. Seeing this, the most likely culprit is the fact that the PDA keeps on switching focus between the two devices that use the serial port: Your BT GPS-receiver and the BT Carkit. When Navigator 5 is running, it pre-empts the serial port connection for the GPS-receiver, which forces the connection to stabilise.
Though we cannot offer you a solution to your problem, please try changing the settings of your BT Serial connection (removing the Authentication and Encryption options).
Kind regards,
The TomTom Customer Support Team
Hi all. I've used my Qtek with TOMTOM and a bluetooth GPS antenna for many time. Some days ago, the system don't run anymore.
The problem is in the Universal Bluetooth: I can find and add bluetooth devices but, when i use it, there is not communication. So, for example, i can connect my Universal with GPS antenna in the bluetooth section, but TOMTOM tell me that there isn't a GPS antenna. Also, i can link via bluetooth my Universal with the notebook, but i cannot start an Activesynk session via bluetooth: it tell me that no pcs are connected even if in the bluetooth list there is my pc and in the service list there is "activesynk" and it is activated.
Now, it is a software or an hardware problem? Any idea? I've anjlurned my software at the AKU 3.2 last italian ROM, but it didn't help.
Thanks in andvance for the help and sorry for my english.
Idum
UP
Pls help me. In what manner i can test if it is an hardware problem or only a software problem?
Idum
I have same problem ...
but still dont know the way how to fix
First
For TT to work with your bt gps you have to create a unsecured incoming port, take COM0 or any other number.
then it should already work in TT, if it not select in TT a GPS receiver and select com0
You have to create a com port for the BT connection and enable that com port in your AS on your pc.
To sync with AS over BT you have to select Connect with BT on your Device!!!
Hi,
I seem to be having a problem with GPS bluetooth related connections with my Dopod 838 Pro.
Ive paired my Globalsat BT338 receiver and setup an outgoing serial port on my Dopod, and I can use Destinator 6 and TomTom 6 fine (for the time being).
The next day/time when I try to start the GPS applications, both programs report that they cant find the GPS signal/receiver even though its been correctly configured to work previously.
I then have to enter the Bluetooth settings to change and assign another outgoing serial port and reconfigure the GPS applications to the new serial port to work.
The programs and the GPS receiver worked fine with my old iPAQ hx4700 so its not a receiver or program issue.
I'm at my wits end and would appreciate any info on solving this problem.
Thanks in advance.
Delete / unpair your GPS
Make a new pair, and when you assign an outgoing COM port, use a NON secure COM port.
(Deselect the checkbox)
This should work
Rik_053 said:
Delete / unpair your GPS
Make a new pair, and when you assign an outgoing COM port, use a NON secure COM port.
(Deselect the checkbox)
This should work
Click to expand...
Click to collapse
Hi,
Ive been through this unpair / pair scenario more than a few times and Ive never used a secure com port connection.
try destinator PN 6
also make sure you pair BEFORE starting Destinator PN; I spent a whole two days before I Got this to work ... then once it worked .. the answer was actually quite logical
sorry cant remember how i did it as it was months ago when I got and paired my tytn; now I use destinator pn 6
njay22 said:
try destinator PN 6
also make sure you pair BEFORE starting Destinator PN; I spent a whole two days before I Got this to work ... then once it worked .. the answer was actually quite logical
sorry cant remember how i did it as it was months ago when I got and paired my tytn; now I use destinator pn 6
Click to expand...
Click to collapse
Hi,
The pairing has been done before any program was launched.
Im trying with both destinator 6 and tomtom 6
Bluetooth GPS Woes...
Is it the Bluetooth connection you are having problems with or getting a GPS signal. I have this exact setup working fine. What I notice is that often it will take a few minutes for the BT-338 to find enough satellites to provide a GPS signal (green light flashing). The bluetooth should connect immediately regardless of whether the GPS signal is available yet. The blue light on the BT-338 should flash twice as fast as when you first turn it on to tell you that it is connected to a Bluetooth device.
I am using TomTom 6 and it will say no GPS signal or GPS signal lost XX seconds ago. Is this similar to what you are noticing?
clearwave1 said:
Is it the Bluetooth connection you are having problems with or getting a GPS signal. I have this exact setup working fine. What I notice is that often it will take a few minutes for the BT-338 to find enough satellites to provide a GPS signal (green light flashing). The bluetooth should connect immediately regardless of whether the GPS signal is available yet. The blue light on the BT-338 should flash twice as fast as when you first turn it on to tell you that it is connected to a Bluetooth device.
I am using TomTom 6 and it will say no GPS signal or GPS signal lost XX seconds ago. Is this similar to what you are noticing?
Click to expand...
Click to collapse
Hi,
Both the bluetooth reciever and the software work fine and obtain a fix.
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
the gps reciver obtains a fix but the pda cant see it.
Destinator PN has an automatic reconnect tick box on the GPS Settings page. I don't know if D6 or TT have a similar thing. If so, make sure this box is ticked.
I use D PN with a Parrot CK3300 combined handsfree and GPS receiver, and after major stuffing around trying to get D PN set to the correct port initially, it has worked fine since.
Ive sorted the issue out and hopefully this will help others experiencing the same problem.
The problem was that although an outgoing serial port was setup, for some reason it was not mapped to the bluetooth device.
It just specified "COM9" instead of having the bluetooth device "BT338(COM9)" under the bluetooth COM Ports setting.
This seems to be the reason why when the device was unpaired/paired and a com port setup it worked for the time being. After the bluetooth device was disconnected the settings mapping to the device were not retained.
Rambler76,
I am looking to get a GPS unit for my Dopod 838Pro. Which of the two, Destinator or Tom Tom, do you like best?
I know where to get Destinator 6 in Sydney, where does one get Tom Tom 6?
Rambler76 said:
Hi,
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
QUOTE]
Can I ask, with a new com port being asssigned each time you have a problem, when you run out of ports what happens?
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Does this make any sense?
Thanks for any input ..
Click to expand...
Click to collapse
killabeezz said:
Rambler76 said:
Hi,
the next time the software is started it cant find the reciver and i have to unpair, repair and set a new comm port for it to work.
QUOTE]
Can I ask, with a new com port being asssigned each time you have a problem, when you run out of ports what happens?
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Does this make any sense?
Thanks for any input ..
Click to expand...
Click to collapse
hi,
what i mean to say is that i switch com ports.
the issue was resolved by mapping the com port to the bluetooth device.
Click to expand...
Click to collapse
Yes I understand what you have done but can I ask again :-
Are you able to regain the use of these once assigned ports ? by resetting any settings ?
Thanks,,
Tom Tom Woes
Hi,
I had the same problem until recently.
To fix I did the following:
Delete pair with GPS receiver,
Create new pair with GPS receiver (put in passkey 0000)
Tick the box for Serial Port
The in Bluetooth Settings -> COM Ports tab, I clicked 'New Outgoing Port'
Selected the GPS unit, and selected Port 4 and unticked the 'Secure' checkbox
Now open TomTom, Select Change Preferences, then Show GPS Status, then Configure, then Other Bluetooth Receiver, then Select COM 4.
Now TT works as it should - turning on and off Bluetooth on Open/Close, and no problems with needing to re-pair.
Previously I had always paired the BT GPS on COM 0 with Secure ticked. This worked the first time only, and I had to re-create the same pair each time I wanted to run the app.
Hope this helps some of you.
(btw I was using TT6 when I found the solution, but I imagine it would have worked for 5 too)
dopod bluetooth problems
Guys I have the same problem with my bluetooth and my dopod. It connects then disconnects.
I have also noticed that the systems unchecks the turn on bluetooth check box and the make this device discoverable to other devices.
Does anyone have any ideas?
Guys I just read this at another forum.
"The Dopod 838 pro and WM5 have chronic problems with the bluetooth stack, which is why everyone is waiting for the new ROM to appear, which will hopefully be WM6. HTC (manufacturers of Dopod 838 pro) announced that the new ROM will fix all of the known problems"
This I learn after having a car accident (minor) in my car playing with the bluetooth and trying to get it to work. Hutchison 3g should only be selling these with a warning.
I assume there is also a problem with the JasJam as they are the same phone.
Knight__Mayor said:
Hi,
To fix I did the following:
The in Bluetooth Settings -> COM Ports tab, I clicked 'New Outgoing Port'
Selected the GPS unit, and selected Port 4 and unticked the 'Secure' checkbox
Click to expand...
Click to collapse
Have to concur with Knight_Mayor. Was having trouble getting a signal/satellite fix using a Holux GPSlim236. Then I set it to COM9 with the "Secure" box unchecked. I had barely closed the window and my M3100 had a fix from inside my house! (tomtom 6 had been running in the background whilst the adjustments were being made)
dabs1 said:
Have to concur with Knight_Mayor. Was having trouble getting a signal/satellite fix using a Holux GPSlim236. Then I set it to COM9 with the "Secure" box unchecked. I had barely closed the window and my M3100 had a fix from inside my house! (tomtom 6 had been running in the background whilst the adjustments were being made)
Click to expand...
Click to collapse
yeah i recon its the screwy MS bluetooth stack, im interested to hear from anyone running tomtom on hermes with the widcomm bluetooth
Tomtom And Gps
I have found that the best cure for gps woes and pocket pc is to use GPS Gate. It make a virtual com port and will always be the same. I have used it always and never have problems connecting.
G