Voice Command Contacts not shown.How to use outres.96.dll ?? - JASJAR, XDA Exec, MDA Pro General

Like many other people, I can't get MS Voice Command to display contact details (but the contact notes can be displayed). I understand that this works on other versions (e.g. The French version) but my problem is with the English version on a T-Mobile Pro.
I've seen suggestions that putting the outres.96.dll file in the \Windows folder allows the contacts to be displayed. However that doesn't work for me, even after a soft reset.
Has anybody got this to work without changing the Universal to a different screen resolution (e.g. using the VGA hack). If you did get it to work then how did you do it ?
Thanks
Peter

Copying the file into the \windows folder does work, when you reset, it should pop up a question about allowing it to run or not, or something along those lines.
I've done it several times, and each time it has worked straight off.

I believe it relates to the version of Voice Command, mine works successfully first time, everytime.

I just type a reply to this question on another thread, doh!
Simon, what version of MS Voice are you using then?
Steve

v 1.50.4333.1
on other posts I noticed those that couldn't get this to work were using the english version of 1.50.4333.21 or similar from memory
I think mine is the us version.
I tried to buy mine but they wouldn't let oz's so was able to acquire through alternate methods....

using MSVC UK V1.50.4333.21
works fine for me everytime.
noticed in another thread http://forum.xda-developers.com/viewtopic.php?t=36016 that a possible problem could be that the pin is blocking the popup to allow the dll to run, I don't set one until it is ready, as it is a pain, so that could be the reason why I've had no problem with it.

Related

MS Voice Command when unit is closed?

Hi all, I am new to this forum.
I own a Dopod 900, and currently trying to get MS Voice Command to work properly with my unit. I believe one of the problem with this application is that it does not respond to command while the unit is in closed mode (the pda screen in inside). Is solution to this problem already available?
I have searched the forum but have not been able to find any solution. I apologize if I missed it, please kindly point me to that posting if there is any.
Any advise is greatly appreciated.
- Josh :?:
From what I've read so far there isn't a fix I'm afraid. It's not fully compatible with WM2005 and will just have to wait for an update from Microsoft :-(
Thanks for your reply. That's too bad. I really have high hope that there is a solution for just this one problem, as there are already tweaks for the other problems. Being unable to receive command in closed mode really make MS Voice Command very much less usable. Too bad.
- Josh
I agree, but at least it's a step up with the other voice dial (that comes it with?). Couldn't do dialling from BT headset at all on WM2003 :-(
The "closed mode" doesn't bother me as I carry the Exec round in a Krusell case, with screen up. This allows me to instantly answer the phone when it rings (having seen who's calling first on the screen).
But there are a few more annoying problems with MS Voice Command 1.5 (I have UK version) present under Windows Mobile 5.0.
This one is unique to WM5.0:
- The first is when I try to call up a certain contact by "Show John Smith", it would show John Smith's contact under WM2003/03SE, but under WM5.0 it just shows blank screen on the Summary tab. This is still a proper contact, if you go to Notes tab, you see proper notes for this contact. You can press Edit and it will be edited... BUT, meanwhile if you just open Contact app, the ones you open are working great.
GBugger...
The following coupla' niggles are also present under WM2003/03SE.
- The days of week when answering "What date is it today" (somehow UK regional settings don't even have it, so I had to enable it in registry under NLS settings) -- all are announced correctly except Wednesday & Thursday, which are sounding simply as "Wed" and "Thu" instead of proper name.
- The signal strength for 1,2,3 and 4 "units" is announced as 30, 60, 90 and 100% correspondingly, instead of 25,50,75,100 which would seem more logical here. I don't know though if it's just caused by something real or an attempt to easily convert
That said, the application is enormously useful especially with the Krusell case, because the carrying shape for Exec in this case is PDA shape with screen up; but it's protected by screen cover of the case and you can't really write on the screen without opening the case -- so voice activation of programs and then controlling them by 5-way navigation control, is really a great way of using the Exec Examples of these programs are the eWallet (ever forgotten your PIN numbers or clothes size?) and speaking date/time, very convenient when you can't look down there.
Hopefully Microsoft corrects these small errors - the WM5.0 devices are the future.
EastExpert said:
Hopefully Microsoft corrects these small errors - the WM5.0 devices are the future.
Click to expand...
Click to collapse
Really, MS should have had this wrapped up ages ago. So disappointed. I want a device like the Exec, but with Voice Command fully working and A2DP sorted, and it's a shame I still can't get all this.
I was so used to the VC software on my JAM, shame the Exec is giving problems.
And I'm tired of tangling my headphones up...
MS, sort all this out already.
EastExpert said:
The first is when I try to call up a certain contact by "Show John Smith", it would show John Smith's contact under WM2003/03SE, but under WM5.0 it just shows blank screen on the Summary tab. This is still a proper contact, if you go to Notes tab, you see proper notes for this contact. You can press Edit and it will be edited... BUT, meanwhile if you just open Contact app, the ones you open are working great.
Click to expand...
Click to collapse
Copy the outres.96.dll into the windows folder and the contact will display correctly.
I'm sorry, but no, it doesn't work for me. Same effect as without outres.96.dll. And yes, I made a soft reset after copying it to the windows dir.
So the next question now is: how to remove the file again?
If I try to delete it, Resco Explorer says "Cannot delete file 'outres.96.dll'. The process cannot access the file because another process has locked a portion of the file."
If the file is useless, then I want to remove it from the device. But it has been blocked by another process.
Thanx in advance
tomestos
I had the same problem but saw the answer on a forum somewhere. After you have installed the dll and do a soft reset as it reboots for a short period it does a security check on the new dll and asks whether you really want to install it, if you answer yes then you will find the blank contacts screen problem is fixed. If you take your eyes off the screen at the end of the soft reset you will miss this security question a it defaults to No after a few seconds. Hope this helps.
I had the same problem but saw the answer on a forum somewhere. After you have installed the dll and do a soft reset as it reboots for a short period it does a security check on the new dll and asks whether you really want to install it, if you answer yes then you will find the blank contacts screen problem is fixed. If you take your eyes off the screen at the end of the soft reset you will miss this security question a it defaults to No after a few seconds. Hope this helps.
guc925 said:
I had the same problem but saw the answer on a forum somewhere. After you have installed the dll and do a soft reset as it reboots for a short period it does a security check on the new dll and asks whether you really want to install it, if you answer yes then you will find the blank contacts screen problem is fixed. If you take your eyes off the screen at the end of the soft reset you will miss this security question a it defaults to No after a few seconds. Hope this helps.
Click to expand...
Click to collapse
I have answered 'yes' to the security check. Nevertheless the dll doesn't work for me. So I want to remove it now, but I can't because it's blocked by some process.
Thanx in advance
tomestos
I've copied the file gnassel suggested into my Windows directory (using the explorer on my desktop pc).... rebooted the exec.. and voila.. it's working like a charm now.. My voice command shows the contact when I say : "Lookup XXXX" or when i call someone, it confirms the person and shows his information just fine. Norte I am usin the u.s. version of voice command 1.5.
Thanks gnassel !
This is a reply to my own posting above.
I did the soft reset using an application called 'psShutXP' (maybe someone knows it; one use it in order to switch off or soft reset the device). Voice Command's contacts mask doesn't worked.
A few minutes ago I soft resetted the device using the "original" reset hole. And voila: Voice Command works as expected!
So there seems to be a difference between "soft reset" using psShutXP and soft reset using the reset hole.
Sorry for the confusion. THE FILE OUTRES.96.DLL WORKS!
By the way: What exactly does outres.96.dll?
Best regards
tomestos
Many thanks gnassel, it works great..
The file was from OzVGA
Thanks for drawing attention to it and posting it, or I wouldnt have know..
Take a thanking damnit
Guys, where do I put the outres.96 dll file again? If I am using File Explorer there is a "WINDOWS" Folder from the very root with a lot of files. Is that the folder I am suposed to put the oures.96 dll file or just leave it outside in the main root?
cktlcmd said:
Is that the folder I am suposed to put the oures.96 dll file?
Click to expand...
Click to collapse
yes
c:\windows\
;-)
gnassel said:
cktlcmd said:
Is that the folder I am suposed to put the oures.96 dll file?
Click to expand...
Click to collapse
yes
c:\windows\
;-)
Click to expand...
Click to collapse
It's "\windows" not "C:\windows".
Best regards
tomestos
Thanks everyone. I thought for a while I have to plug it in my computer too.

Voice speed dial - voice command

Ok guys.....So I have a wing with PDAVIET .14 ROM. I pretty much switched as soon as i got the phone so i havent had much experience with the standard tmo rom but i am having an issue with my Voice speed dial. Basically if i go to the programs and click on the application it works fine..i can attach voice recognition titles to different contacts.
The problem that I am running into is when i assign the button on the wing (one right above the messages button) and push and hold it gives me the error.
"The file 'VoiceCmd' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file."
But it does work directly from the .exe file. Whats wrong here? It does say to reinstall if the problem persists so...what is the most recent edition for the wing? or is that even necessary to do that. I tried to run the app from a couple buttons but nothing. In a whole, i'm trying to get my voice command to work through my bluetooth. am I going about this totally wrong?
Comments appreciated!
lokmeup said:
Here is a MS Voice Command 1.6 and BT Patch ONLY ExtROM that I use when building my ROMs. It will install everything the exact way necessary to get announcements and BT to work without any further changes. Just install, Run, Pair your BT, Soft Reset, and have fun.
MSVoiceCommand1.6_and _BTpatch_ExtROM.zip
http://www.sendspace.com/file/3xqdnc
If you only wanted the CABs...
MSVoiceCommand1.6_and _BTpatch_CABs.zip
http://www.sendspace.com/file/bq815x
Ron
Click to expand...
Click to collapse
So I did a bit of searching and I just decided to install voice command from the above thread. I know that it was in the Hermes forum but i assumed it would be all good. Now i have tried both of them and figured out how to get them to work. so now they are both working with the handset, all gravy. I think i am going to keep the speed dialer that came on the rom it seems to be more accurate.. Also how to use my earbud to prompt the command, i cant get that squared away with either applications. Anyone have a suggestion?
How did you get rid of the message? Even though I installed the cab, assigned the button (button 4 hold), it is still giving me annoying VoiceCMD error like yours. Can you do a create a brief procedure? Is it a simple reg edit? Where? Thanks... Hope to hear from you soon.
Can someone post or PM me another link to download MS voice command? the two links above are not working. Thanks
thenyccharles said:
Can someone post or PM me another link to download MS voice command? the two links above are not working. Thanks
Click to expand...
Click to collapse
I don't or can't use Voice Command. Trying to uninstall Voice Command as it does not work for me at all.
Here is a Cab file for Voice Speed Dial. Installed it yesterday on my Wing and it works great. Try it and you may want it instead of Voice Command. I think it does everything better than VC. Let me know your opinion.
Thanks I will give it a try...
asctony said:
I don't or can't use Voice Command. Trying to uninstall Voice Command as it does not work for me at all.
Here is a Cab file for Voice Speed Dial. Installed it yesterday on my Wing and it works great. Try it and you may want it instead of Voice Command. I think it does everything better than VC. Let me know your opinion.
Click to expand...
Click to collapse
Thanks. this version works well.....
asctony said:
I don't or can't use Voice Command. Trying to uninstall Voice Command as it does not work for me at all.
Here is a Cab file for Voice Speed Dial. Installed it yesterday on my Wing and it works great. Try it and you may want it instead of Voice Command. I think it does everything better than VC. Let me know your opinion.
Click to expand...
Click to collapse
Thank for file
Thanks. Works fine on my HTC P4351 (Wing) with ROM JustStable-Micro 6.1
does it work for WM6.5?
i have omnia i900
after i flashed it, i can't use voice speed dial
i read the post later, and he said he removed it
Thay is what I am wondering as well. That is the only thing thay I notice in Glass v.10 as being a bug - when I press and hold the button I get an error saying "the fole voicecmd cannot be found."

Blackberry Connect on Topaz working

Hello Together,
here's solution on how to get Blackberry Connect running on Topaz:
Instructions:
------------
- Make sure you have uninstalled blackberry connect before doing the following.
- Attached you will find a small zipped executable (EnableBBCTopaz.exe). Unzip it and copy it over to the \windows\ folder of your device.
- Open a registry editor and navigate to HKLM\init
Create a new string with the name "Launch130" and a value of "EnableBBCTopaz.exe" (without the quotes of course)
If Launch130 already exists, choose a number higher than, it doesn't really matter, just make sure it is higher than the other entries so it get started after everything else.
This makes sure the exe ist started after every softreset.
- Make a softreset, or execute the EnableBBCTopaz.exe manually.
- The program changes your model-id from "HTC-Topaz" to "HTC-Raphael" in memory
- Install Blackberry Connect like you usually do (My tests where successfull with version 4.0.0.104, 4.0.0.106 didn't work for me -- just hung up after a restart)
- After installation and the auto-reset through BBC open the BBC settings and go to the Info-Tab. Under device-name there should now be HTC-Raphael.
Click to expand...
Click to collapse
The solution is in fact the one from Rhodium forum, the respect goes to them, in particular to c0rnholio. The instructions are also copied from their thread. I just changed the program to fit to Topaz.
hi gnick.
Thanks a lot for providing a solution for this issue, but I cannot get it working...
The Client keeps stating: "PIN Pending". When I try to register the account the data tunnel gets established for a second but then it gets disconnected again.
The SIM is working fine in a Blackberry.
I already tried to reinstall the BB Client several times, but I always got the same results.
The device-ID is set to HTC-Raphael, so that shouldn't cause any issues.
Additionally I tried to kill the bbmain.exe and suspended the log and security services and reenabled them after a few seconds, but still no success.
If you have any further hints on what to try, pls. let me know...
Thanks in advance,
TheOmen666
Which blackberry client version do you have?
TheOmen666 said:
hi gnick.
Thanks a lot for providing a solution for this issue, but I cannot get it working...
The Client keeps stating: "PIN Pending". When I try to register the account the data tunnel gets established for a second but then it gets disconnected again.
The SIM is working fine in a Blackberry.
I already tried to reinstall the BB Client several times, but I always got the same results.
The device-ID is set to HTC-Raphael, so that shouldn't cause any issues.
Additionally I tried to kill the bbmain.exe and suspended the log and security services and reenabled them after a few seconds, but still no success.
If you have any further hints on what to try, pls. let me know...
Thanks in advance,
TheOmen666
Click to expand...
Click to collapse
Hi again,
I tried with versions .106 and .104.
Same behaviour with both versions ;(
TheOmen666
Hmm, hard to tell, really.
Which provider do you have? Your provider needs to support HTC Raphael.
Mine (Vodafone Germany) does support HTC Raphael (Touch Pro).
gnick said:
Hmm, hard to tell, really.
Which provider do you have? Your provider needs to support HTC Raphael.
Mine (Vodafone Germany) does support HTC Raphael (Touch Pro).
Click to expand...
Click to collapse
Thanks for the tip, but I too cannot get it to work. It did work in my HTC Diamond (that's Diamond "1", not "2"). I wonder - can you change the programme to suit the Diamond 1 instead please? I mean Diamond 1 instead of HTC Raphael. I wonder if this will make a difference.
By the way, does anyone know if RIM will bring out any software to make this all work?
Hi mitsi, did it work at the end?
mitsi said:
Thanks for the tip, but I too cannot get it to work. It did work in my HTC Diamond (that's Diamond "1", not "2"). I wonder - can you change the programme to suit the Diamond 1 instead please? I mean Diamond 1 instead of HTC Raphael. I wonder if this will make a difference.
By the way, does anyone know if RIM will bring out any software to make this all work?
Click to expand...
Click to collapse
gnick said:
Hi mitsi, did it work at the end?
Click to expand...
Click to collapse
Hi Gnick, partly. I got it to work with stopping the Blackberry Service and then activating the programme (your one) after a soft reset. However, after every soft reset, I will need to do the same process.
Open MemMaid
Stop Blackberry Service
Open File Explorer
Start your programme
Open File Explorer
Start BlackberryMain.exe
Close File Explorer
Enjoy emails.
This is too much like hard work, so I think I will be either selling my Diamond 2 and going back to my Diamond 1 or keeping both, using the Diamond 1 and waiting for a better fix to become available by subscribing to this thread (and others) and hoping that decent clever chaps like yourself will come up with a fix!!!
By the way, one other item that needs fixing is that I am only able to have my work email on this. I do not have the Blackberry Secure Internet (the one to send service packs and add other email accounts). So I can't get my home email..
There is one other alternative by the way:
This is to write a Mortscript programme that does this tedious process automatically.... I have made enquiries to someone I know....
@gnick
Thats a good point, asking for the Provider...
Well I checked the websites of T-Mobile Germany and the last device I found, where you could officially download the bbconnect client was the "Kaiser" (Mda Vario III, HTC TyTN II, AT&T Tilt ).
This means, that I either have to get rid of my Topaz or convince you to make a special version where the model-id is set to the one of the Kaiser (I only found "KAIS120") but I am absolutely unsure wether this is the korrekt model id used for the bbconnect client.
Regards,
TheOmen666
Hi All,
I finally got it working.
As I am running WM 6.5 on my device, I had to change the AKU String in the Registry HKLM\System\Versions to ".1.6.3".
After changing this, I got a PIN and could do the Enterprise Activation with my account.
Thanks a lot to all for the effort to get this working on the Topaz.
Cheers,
TheOmen666
Hi All,
I too got it working. I followed the tips on this thread and on the one by cOrnholio with the following notes:
AKU set to .1.6.1
BBC version 104 worked (106 didn't) just as you said gnick .
Blackberry still crashes Manila sometimes when deleting the last email and exiting tmail.
I cannot activate my other email accounts as the Blackberry Browser (I think this is BES) does not load, even after the prompt "The internet connection is currently in use by the BlackBerry browser. Would you like to temporarily disable BlackBerry browsing? Yes/No". Once disabled and refreshed, it still does not connect. I think I read this on cOrnholio's thread.
Sent mail from pc does not redirect mail to the sent mail folder on the D2 but into the inbox instead.
The soft reset problem still exists, but it does at least work. My D2 has now had emails for the last 3 days.... Fortunately the D2 is more stable than the D1 so soft resets are required less often.
My thanks go to gnick and cOrnholio for this. I can now use my D2!
By the way, I have made some simple shortcuts which make the process following a soft reset simpler:
Add shortcut to BBMain.exe to the start menu
Add shortcut to MemMaid to the start menu
Set MemMaid to re-open at same page in Advanced Settings
A couple more tips for new people at this:
Be patient. Sometimes you can try the same solution more than twice and get different results
Be patient. The IP Address and PIN don't always appear immediately.....
Regards
Hi All,
Me too.
I got it working. I followed the same tips on this thread and on the one by cOrnholio with the following notes:
AKU set to .1.6.1
BBC version 104 worked.
Orange Romania.
Everything is ok !
mitsi said:
By the way, I have made some simple shortcuts which make the process following a soft reset simpler:
Click to expand...
Click to collapse
Hello mitsi, setting the "Launch130" key in the registry to EnableBBCTopaz.exe as described in the instruction in the first posting should ensure that EnableBBCTopaz.exe starts automatically befire BBC. This is the "clever" way to autostart it without doing any manual work. If it doesnt autostart, that could mean that you have a spelling error in the regkey name, regkey value, or that you havent placed the file in the \windows folder.
gnick said:
Hello mitsi, setting the "Launch130" key in the registry to EnableBBCTopaz.exe as described in the instruction in the first posting should ensure that EnableBBCTopaz.exe starts automatically befire BBC. This is the "clever" way to autostart it without doing any manual work. If it doesnt autostart, that could mean that you have a spelling error in the regkey name, regkey value, or that you havent placed the file in the \windows folder.
Click to expand...
Click to collapse
Hi gnick,
I must admit, I haven't checked this, but I have had problems before with Blackberry. Because our IT Dept in their wisdom have set the security to lock the phone after 60 minutes of inactivity, I keep having to unlock it. I have a Mortscript programme which does this for me thanks to EdSub, but it would appear that Blackberry takes a higher pecking order after a soft reset so the Mortscript isn't activated before Blackberry, no matter how I try to configure it. Therefore, I suspect Blackberry will start before your programme too, so it would then think the phone is a D2 instead of a Rafael immediately after soft reset.....
If your Blackberry has the Security Policy set by your IT Department, you too may have this issue, but otherwise, it may be possible to start your programme before Blackberry starts.
Isn't it all rather silly??? The things we do to get our phones to our liking eh???
Hi !
thanks for this thread !
it seems to work for me, (appear as raphael
done in a minute...now waiting my PIN
how long does it takes ?
regards
cédric
tsetse_fr said:
Hi !
thanks for this thread !
it seems to work for me, (appear as raphael
done in a minute...now waiting my PIN
how long does it takes ?
regards
cédric
Click to expand...
Click to collapse
It shouldn't take longer than a few minutes. You may be able to help it on it's way by going into Blackberry settings, then in the Utility tab, press "Register Now". Then if you go to the Identy tab your PIN and IP address should appear hopefully.
nothing appens when i press "activate now "....
same probleme with a touch hd ...Bes account has been reset ...but pin and ip still pending
i'll wait ...
want a good new : already broke my digitizer yesterday :s got to change it ...
News from HTC
Hi All,
For your information, I sent the following question to HTC:
"Dear Sirs, I have an HTC Touch Diamond 2. I have requested information before on how to get Blackberry Connect working on this phone but had the response "we don't support third party applications". This is fair enough, but please see this link: http://www.htc.com/sea/SupportViewNews.aspx?dl_id=497&news_id=61. If you support this on other HTC phones, then why not the Diamond 2? Do you have plans to develop this further? I would appreciate your help/comments on this please."
I received this response from HTC:
"New Response From [ Mike (EU team) ]
Hi Paul,
The link you found is for Asian devices, not European ones.
Blackberry Connect is not supported by HTC Europe and there are no plans to release the 3rd party application or test its compatibility.
Please contact Research In MOtion to see if there is compatible version for your device.
Best Regards
Mike"
Hopefully they will change their minds in the future. Has anyone tried RIM?
mine worked 2 days later
had to wait only because my orange data network was pending ...
now it works perfectly

A new Android package is released for Diamond

Hi,
I found this
http://connect-utb.com/index.php?option=com_rokdownloads&view=folder&Itemid=68&id=2:android-port
http://connect-utb.com/index.php?option=com_jdownloads&Itemid=58&task=viewcategory&catid=5
http://connect-utb.com/index.php?op...8&id=20:android-for-htc-touch-diamond-diam500
Anyone want to try?
Does this replace Windows Mobile or run along side of it? If it replaces it, anybody know of an Windows Mobile 6.1 Stock Sprint ROM?
you do know that in Rom Development there is a whole 4,000 odd posts about this and its development? have a look here.
http://forum.xda-developers.com/showthread.php?t=402002
and no it doesn't replace windows what it does it using haret it boot loads linux and effectively runs android as if it were its stock rom, but doesn't delete WinMo, and its not an emulator. see the thread above for more details.
New ?
21.06.09
http://connect-utb.com/index.php?op...=file&Itemid=68&id=29:android-for-htc-diamond
im not sure if this works for DIAM500 or not but have a go. it works for me but im on DIAM100 but it still freezes but i can actually make and receive calls.
!!! USE
I use it for 3 days, only problem sometimes it says battery is empty, wireless is not working and bluetooth is not working,, it doesnt replace windows,,. and it works perfect
HI!
I've searched without luck for month now: I've got an DIAM300 and i could not get to startup any android version (hanging on glowing android).
Does anyone know the difference between diam100,110,500 and my diam 300??
answer in diam forum was "sorry, but you've the second person i've met who owns an diam300"
My diam300 is an HTC diamond german O2 version (round corners on cover)
Thanks for help!
Good news ! It can call
but the battery lost very fast
infantilo said:
HI!
I've searched without luck for month now: I've got an DIAM300 and i could not get to startup any android version (hanging on glowing android).
Does anyone know the difference between diam100,110,500 and my diam 300??
answer in diam forum was "sorry, but you've the second person i've met who owns an diam300"
My diam300 is an HTC diamond german O2 version (round corners on cover)
Thanks for help!
Click to expand...
Click to collapse
the same for me, DIAM300, xda diamond from German o2 and the package don't work, stucks in boot process (text) earlier packages worked fine, tried to combine the the old package with the new one, but no luck :/
I have DIAM300 and it is working with this:
http://connect-utb.com/index.php?op...=file&Itemid=68&id=29:android-for-htc-diamond
matrix77 said:
I have DIAM300 and it is working with this:
http://connect-utb.com/index.php?op...=file&Itemid=68&id=29:android-for-htc-diamond
Click to expand...
Click to collapse
I used that download and it does not work for me have you changed anything or just download, unpack, copy to the phone and run haret.exe?
for me it always "hangs" at:
[ xxx.xxxxxx] msmfb_start_dma 90.yyy ms vsync request
the xxx.xxxxx is counting and the yyy is changing but "random" ..
I didn't change anything, it works fine but when I lock the screen I must reset the phone because I can't unlock it in Android.
matrix77 said:
I didn't change anything, it works fine but when I lock the screen I must reset the phone because I can't unlock it in Android.
Click to expand...
Click to collapse
hm.. okay, thank you
My DIAM 300 hangs at msmfb_start_dma 90.yyy ms vsync request :-(
Any solution? PLZ!!!!!!!!!!
Hi all,
I installed android package, few minutes ago, and it works fine.
Unfortunately, usage is little bit difficult beacuse of the missing application, or not manageable. Using the media player or during a phone call, it is not possible to listen audio with the headphones?
It is possible to install usefull application as TomTom?
divxmaniak said:
Hi all,
I installed android package, few minutes ago, and it works fine.
Unfortunately, usage is little bit difficult beacuse of the missing application, or not manageable. Using the media player or during a phone call, it is not possible to listen audio with the headphones?
It is possible to install usefull application as TomTom?
Click to expand...
Click to collapse
audio support is not complete on most devices. Not managed to boot properly into diamond version yet because of same issue as mentioned above. suggest trying the other zImage, it might work better.
your usual apps are written for windows mobile....you are no longer using windows mobile, you are using android. If TomTom write an android version then maybe you can run it....until then, no.
Just downloaded and installed Android for HTC Touch Pro and my Touch Pro boot succesfully. I managed to get to the "SIM card is locked" screen, however when i enter my PIN code i get "Incorrect PIN code. I know i have entered the correct PIN code.
Anybode else experienced this or have a suggestion what i could do.
Thanks
Nevermind, i found the solution at Connect-UTB's forum:
Q: When launching Android, it asks for my PIN-code, but it doesnt accept the one i type in!
A: You have to disable the PIN-Code authentication in Windows Mobile before booting up Android.
Got a Solution in the extracted folder there is the kernel _old rename it

Is MS Voice Command 1.60 compatible with HD2 running WM 6.5.5?

I bought Microsoft Voice Command 1.60 and I tried to install it on a HTC HD2 mobile that runs Windows Mobile 6.5.5 (cooked ROM), but I always get an error message at the end of the installation, which says:
An unrecoverable error occurred in Setup. Please reset the device and try again
On the Handandgo website is listed that HTC HD2 and Ms Voice Command 1.60 are compatible, and the technical support of Handandgo confirmed it me that once once more.
I have tried:
- at least 3 different ROMs, (Freyberry barebone, Miri, 3l5y)
- at least 2 Stock ROM (1.43 and 1.66)
The error occurs even if I install from the PC using Windows Mobile Device Center or when I install from a downloaded cab files, located on my phone SD card.
Please can anyone suggest a solution?
Thanks
It might be that this latest and previous editions of MS Voice Command are NOT compatible with HD2
Can anyone confirm?
Thanks
Saulo
Or does it need to have NetworkFrame 3.5?
If so, how do I know if I am running standard 2.0 version or latest 3.5 version?
Thanks again
Saulo
1) Have you checked that it works, i had this broblem after install on my old TD and it still worked. If i remember correctly it did not assign it to button 1 correctly either and you had to put a shortcut into the start menu then assign it to button 1.
2) I have not been able to get any version of MSVC to work on my Leo with 6.5.x, I am using Cyberon now... it is a bit of a pain having to go through all the contacts teaching it, but it works well.
Better use Cyberon Voice Command. Its
compatible,
more comfortable to use (no voice assignment necessary),
attachable to longpresssendkey even with bluetooth-headset easily (if this option is enabled, otherwise search for S64 enable send key)
and has more functions than MVC
Greets
Thanks a lot elburna
I will surely give a try to that application you mention
Now my problem is how to unistall...in fact also unistall runs in the same error message...
I dislike to have my system dirty with aborted installations and aborted removals. can you advice it?
Thank you!
Saulo
Dear elburna
Where can I download a trial or buy the latest version of cyberon voice command?
No sign of it on handango.com and pocketgear.com
On the official site
http://www.cyberon.com.tw/download.php
I just see corporate solutions...
Thank you
Saulo
Do a search for Duttys Cyberon Voice Speed Dial it is oem.... free
saulo866 said:
Dear elburna
Where can I download a trial or buy the latest version of cyberon voice command?
No sign of it on handango.com and pocketgear.com
On the official site
http://www.cyberon.com.tw/download.php
I just see corporate solutions...
Thank you
Saulo
Click to expand...
Click to collapse
This site is just right. Download the trial here
http://www.cyberon.com.tw/download.php
and if you like it you just need to use the register button on their page
dear Elburna
I have tried Cyberon and works very good (altough my english pronunciation is not good and many contacts are mistaken)
I have purchased via paypal 1 hour ago, to support them, $20...up to now I have NOT received any serial. Did you also wait a long time before receiving unlocking code?
2.
Is it possible to install another language? Say Italian? Or French?
3.
Is it possible to install Chinese Language (I am learning it)
Thanks
Saulo
saulo866 said:
dear Elburna
I have tried Cyberon and works very good (altough my english pronunciation is not good and many contacts are mistaken)
I have purchased via paypal 1 hour ago, to support them, $20...up to now I have NOT received any serial. Did you also wait a long time before receiving unlocking code?
2.
Is it possible to install another language? Say Italian? Or French?
3.
Is it possible to install Chinese Language (I am learning it)
Thanks
Saulo
Click to expand...
Click to collapse
Im not quiet sure but i think (didnt test it yet) you can install any of the trials from their website (french, italian, and so on, unfortunately no chinese only japanese ) and unlock them with your code. If you dont like it you can go back to your old version any time.
For me it took a whole day till the registration code was sent because i ordered in the afternoon hours as well (takes some time till they check their paypal-/email-account), so dont worry
I am trying Cyberon Voice Command. Sound and voice work through the bluetooth headset but I cannot get the Bluetooth Headset to start the command.
I have also tried Microsoft VC, this works ok except i do not get the tone at the beggining or the failed tone.
Anybody experianced and of these problems and any sollutions.
What the hell? I've been using MSVC on mine for ages now, even over bluetooth.
On older ROM's it didn't, but since the latest T-Mobile build's it's been fine.
I'm using Miri Rom 7.0 on 6.5.5. I've assigned the longpress send key to activate and it works without issue. Furthermore, it installs then says some sort of error occurred, but I just press okay, and the back key and it works great!!
HI Guys,
because I am total noob in MSVC, could you please answer a few questions for me? I seem to have it embedded in my Xanny 1.4 Evolution (6.5.5) rom, but I haven't got any idea how to set it up or use it...
So firstly:
Does it work like I for example say: "Call Edward" or something and it will do it? Where do I set that up? Where do I record and apply the command?
Secondly:
Does it work only on bluetooth headset, or a wired headset (or no headset at all ) can be also used?
And lastly:
Does it need to be switched on/off whenever I want to use it or is it just another ongoing service?
Thanks!
MSVC on XannyTech Evo 1.4
morningstar.fallen said:
HI Guys,
because I am total noob in MSVC, could you please answer a few questions for me? I seem to have it embedded in my Xanny 1.4 Evolution (6.5.5) rom, but I haven't got any idea how to set it up or use it...
So firstly:
Does it work like I for example say: "Call Edward" or something and it will do it? Where do I set that up? Where do I record and apply the command?
Secondly:
Does it work only on bluetooth headset, or a wired headset (or no headset at all ) can be also used?
And lastly:
Does it need to be switched on/off whenever I want to use it or is it just another ongoing service?
Thanks!
Click to expand...
Click to collapse
I've been using the same ROM and my BT headset is Jabra Extreme. It works well.
Go to [Settings][Other][Voice Command] to set the MSVC to your liking. Actually, you don't need to as the presets are working well. Only you can check whether it is enable or not.
Click on your BT headset button and say the command after the beep. Better still after the beep say "Help" and you will be guided on the capabilities.
Don't know about wired headsets because I only use it on bluetooth headset.
You must activate the bluetooth services and pair your headset first. I usually leave the bluetooth services on or you can d/l the BT toggle to save battery. Frankly speaking, I leave the BT services on and the battery saving is minimal.
Hope that helps.
Ok, so it only works through headset then. Possibly only trhrough BT one... So I can't just talk to my phone without using any headset...? I guess I can (but I'd probably end up locked in mental institute...).
Voice Command with HTC HD2
Hi Guys been followingthis thread i have installed Voice command it seems to be working with regards to telling it to call my contacts however it does not read my emails to me as it used to do on my Imate Ultimate 9502 i have double checked all the settings etc they are set as per the imate but i cannot get it to read new messages any ideas?
I always got the install error when installing MSVC.. but i just ignored it and it works anyway..
does it read new messages?
I get the same error when installing and ignore them but it refuses to read new text messages
well for those intereseted after testing and many different solutions
the vedic is that the HTSense sms message system is not registering with voice command.
command voice dial and programm access works
appointment reminders work and new incoming emails are anounced and read aloud.
the only thing that still does not work is new incoming sms's are not read aloud.

Categories

Resources