i had my qtek 9000 in my pocket when i got out of my car...it fell on the ground and now the screen is broken...
al the functions still work (touchscreen and all)...the only thing is it has a crack in the upper righthand corner with a grey spot around it...everything projected underneath this spot is invisible...
anybody have any idea as where i can send my qek to get repaired, or where i can order a screen and do the repair myself..
has anybody seen a step-by-step explanation (with pictures), on how to open the qtek (jasjar)
thanx in advance
hi,
dont know if this helps but i read somewhere in this forum that a fujitsu siemens pocketloox 720 pda uses the same display....
Good luck
Wayne
thqt would be a step in the right direction....can anyone confirm this, as the replacement screens for qtek or jasjar aren't anywhere to be found
Just return it to any official Proximus-shop or even Belgacom-shop, they'll take care of it.
You should count on 6-8 weeks and a cost of 140 €
Related
I have a replacement screen fror my Alpine. I located a site a while ago which showed in text and photos how to open up the xda IIi, but now I can't find it and I don't want to break anything guessing, any help would be appreciated.
Hi,
Can you please tell me where did you get the replacement screen ? I bought Alpine 5 days back and suddenly its screen is not working anymore. (PDA is fine only touchpad is not working). I can install all softwares and it works ok, but no more touch sensitive.
Rgds,
Qbukhari
qbukhari said:
Hi,
Can you please tell me where did you get the replacement screen ? I bought Alpine 5 days back and suddenly its screen is not working anymore. (PDA is fine only touchpad is not working). I can install all softwares and it works ok, but no more touch sensitive.
Rgds,
Qbukhari
Click to expand...
Click to collapse
I got the screen from here, http://www.runpda.com/ , it cost £93.00
including shipping. But I got stung by UK Customs for £38.00 Tax, rip-off, so it cost me £131.00 in total. I've bought from this part of the world before and not been charged by taxman, its just the luck of the draw.
Someone suggested this place in the UK, but I had already ordered, if anybody tries this one, post costs etc for everyone. Mobile Repair Centre in London. 177a North end road 0207 610 3103.
I used this manual to open case, all the instructions are ok,
ftp://xda:[email protected]/Himalaya/Himalaya-Service-Manual/
they only bit that is confusing is the opening of the black plastic cover, basically follow manuals instructions to open cover by pen holder side, then slid a thin piece of plastic in the gap and slid along (I made a plastic tool from cutting a thickish plastic bottle). In the picture it looks like you place it in the SD slot, this is not the case, just slid along the edge of the gap you have created by the pen holder. :lol:
Hi again,
Forgot to mention, that the internally the screen just pushs onto a connector on the motherboard (just pull gently upwards to remove). I would disconnect it and reconnect it, and put your Alpine back together, just to see whether it was loose or not) Please ensure you use the write screw drivers as the screws are very small and you don't want to round them off), you need a mini philips screwdriver and a T6 size Torc screwdriver.
I'm not sure where you bought it from but if it is retail, then I would exchange or get your money back, if like me you bought privately then I hope my info helps you.
I (my 1.5 year old daughter) managed to crack the LCD display on my new TyTN(!!!). I tried transplanting in it an old HTC Wizard display that I had, which turns on as blank white and therefore doesn't help me... I have been looking on ebay and found a company from HK that sells new displays. They have generation 1 or 2 types. see here: http://cgi.ebay.com/Full-LCD-Screen...hZ015QQcategoryZ41343QQtcZphotoQQcmdZViewItem
I assume this is probably the problem I have (??) I guess the display generations are different.
Does anybody have any insight into this? Has anybody replaced an LCD display in their TyTN?
I'll be happy to provide a detailed step-by-step on how to do the replacement if anybody is in the same #$%@y situation I am in...
I'd greatly appreciate any information... I need my phone back...
I deleted your duplicate post in the Upgrading forum btw.
T-mobile Vario II
Hi I have a Tytn from T-mobile (the Vario II). I've been searching here in the uk for a LCD screen also and cannot find one for this anywhere! If you figure it out please let me know, I would be extremely grateful. Taking it to a place called Carphone warhouse tomorrow hopefully they can repair it. Will let you know thanks.
Don't know if it will help you or not, but here it is the part number of HTC TyTN screen, I got it on the description sheet after service center fixed screen alignment issue on mine:
Code: HTC60H00037-01M
Description: TFT-LCD MODULE, TD028STEB1, NEW SUNPLUS, TOPPOLY, TYTN
It was an HTC TyTN with S/N HTC628.
Also try to google this.
pof said:
Don't know if it will help you or not, but here it is the part number of HTC TyTN screen, I got it on the description sheet after service center fixed screen alignment issue on mine:
Code: HTC60H00037-01M
Description: TFT-LCD MODULE, TD028STEB1, NEW SUNPLUS, TOPPOLY, TYTN
It was an HTC TyTN with S/N HTC628.
Also try to google this.
Click to expand...
Click to collapse
Try this site:
http://brisklouis.trustpass.alibaba.com/productlist.html
or here
http://www.briskhk.com/product/DigitalPDA.asp?ProductsubID=1
This LCD also has an HTC Part No:
HTC code:60H00037-00
and is also used in:
Dopod818/Qteks200/828/838/qtek9100/HTC Magician,Wizard,Apache/MDA compact/XDA II mimi/UTStarcomm PPC-6700
Mike
OK, so I first tried to place a display from a dead HTC-Wizard in my TyTN - which does not work. It fits perfectly, but all I get is a white screen and somehow it is draining the battery in 1/2 a day. They must have changed something in the display. For now I am only using my phone via voice command to place and receive calls :-(
I ordered a new display from http://stores.ebay.com/hitechhk
They claim as I mentioned to have TyTN displays with generation 1 or 2 although the image says they are displays for O2 mini. I sent a query asking what generation would I need based on photos of my broken display (which looked different than both!). I got a reply that their tech was looking at the pictures to determine which display I need and then got a response that the item shipped - that's communicating across the globe for you... Anyway, my new display is on the way and hopefully it works. I have no idea what they shipped.
I looked at some of the links posted by mikechannon and pof above and these sites seem more B2B (no place to place an order).
Anyway, I'll let you know as soon as it arrives (it shipped 2 days ago) if I'm lucky or not. If so - it's a pretty easy solution. If not...
OK, I am very confused now...
I got my display yesterday from hightechhk - it is not compatible.
Quite frankly, it is identical to my old HTC wizard display and only produces a blank white screen on the TyTN.
Note that this is part number TD028STEB1 and despite the previous mentions that this is TyTN compatible - it is not in my case...
I am back to square one - trying to get an exchange / refund from hightechhk.
Otherwise, my only route will be repair by HTC America (if they take it...).
ygeller said:
OK, I am very confused now...
I got my display yesterday from hightechhk - it is not compatible.
Quite frankly, it is identical to my old HTC wizard display and only produces a blank white screen on the TyTN.
Note that this is part number TD028STEB1 and despite the previous mentions that this is TyTN compatible - it is not in my case...
I am back to square one - trying to get an exchange / refund from hightechhk.
Otherwise, my only route will be repair by HTC America (if they take it...).
Click to expand...
Click to collapse
I just wonder if there is something else wrong and the replacement screen is fine - possibly digitizer. Have you tried a hard reset?
I just decided to start my contingency plan - repair by HTC.
This ordeal started by calling HTC America, who forwarded me to HTC UK.
I need apparently to send my phone to the UK for repair...
Anyway, to your question - I dare not try a hard reset yet until I am officially ready to send my phone for repair to HTC. The reason is that I am using the phone via voice command (the display is dead - so no dialing there...). If I hard reset - I can really only answer incoming calls...
Anyway - I'll give it a try before I ship it, although I doubt it will work.
I have been around many places in the UK...
and can only find two places which will repair it, both costing £150!!! ygeller
do you have the number for HTC in the UK thank you very much hope you get the screen fixed.
I got these numbers: +44 (0) 8458900079 HTC UK
+44 (0) 1202714530
After talking to someone on the first number I was told to call the repair center:
+44 1 908556464 repair center
The repair center hardly answers - you leave a message and they call you back.
I then went to http://support.htceurope.com and created my own repair request. I got a price estimate which was more like 100 GPB including shipping to the US and 5 days typical turnaround. The website generated the RMA process and claimed to have sent me an email with the return instructions - so far, I have not received the email... unbelievable...
Yes. The price sucks. Then again having paid so much for the phone and not being able to use it sucks more...
Yep that ties up with this site:
http://www.europe.htc.com/support/cs_by_phone.html
Mike
For reference, I now finally see that the part number I am missing is:
60H00056-00M
the part I got from HK (fits the HTC Wizard) is 60H00037-00M
Hence the mismatch.
Searching the "37" part on google yeilds all sorts of results.
Searching for the "56" part yields nothing... to new? :-(
ygeller Thanks!
Thank you very much ygeller, you have saved me at least £50 and the turnaround is a lot shorter than the 4 weeks I was quoted somewhere else. The internet is a wonderful place most of the time seriously thanks again! Hope all goes well with yours once you get it back.
Problem
Hi!
I have similar problem.
While the charge of battery is over 95% touch screen response me, but later no, rest of device continues working perfectly.
Ygeller, what generation of lcd purchase you?
Ì'm sure that the 1st is not for my device (vodafone v1605 HERM200) but i'm not sure if 2nd will be correct for me.
And if somebody has passed him similar problem and has a solution estaria him very thanked for if me it explained it.
Excuse my bad english.
It was neither gen1 or gen2.
The display they sent me was simply incompatible. It was a Wizard screen - not TyTN.
I couldn't find anywhere on the web a replacement part for TyTN, so I sent it for repair by HTC.
Tytn LCD Module
Just read through thread - trying to pick up on LCD module suppliers.
It seems there is some confusion as to the type of LCD the HTC Tytn and its various "brother" PDA use. Here is what I found out after some extensive correspondence with a supplier in China:
There are a number of incompatible LCD modules each of which is fitted with its own video controller. The marking (usually) with a big sticker on the ribbon like connector states which type is used.
These are the descriptors to look for and order by:
Samsung - LTP280QV-E01
Toppoly - TD025STEB1
Hitachi - TX0704APAA1
The other codes mentioned in the thread are equivalent:
Hitachi - 60H00056-00m
etc...
In any case if anyone knows where to find the Hitachi I would be very happy!
I just got finished replacing the screen on my 8525. I got it from e-bay (gold electronics) had good service and got the exact screen for my phone. around 79 + shipping.
Which screen did you replace?
Info on Tytn LCD Types
Hope this sorts the "White Screen" business out...
These screens differ in the controller they need.
HTC has diversified its use of LCD modules probably to cut prices... but it is a pain to fix!
(1) Samsung LTP280QV-E01
AKA: 60H00032-00M
http://cgi.ebay.com/HTC-TyTN-Hermes...ryZ38331QQrdZ1QQssPageNameZWD1VQQcmdZViewItem
(2) Toppoly TD028STEB1
AKA: 60H00037-00M, Black Label
http://cgi.ebay.com/HTC-TyTN-Dopod-...sPageNameZWD1VQQcmdZViewItem#ebayphotohosting
(3) Hitachi TX0704APAA1
AKA: 60H00056-00H
No link available - unfortunately what I need
jep.. i broke my screen.
i guess i sat on it or dropped it when is was boozed up ..
its got a crack in it and its not coverd by the garantee, whoe.. what a surpirse ..
does anyone knows what type number the touchscreen is?? i can fix it myself..
but i have no idea where i can buy the correct type screen..
can anybody enlighten me ??
greetz sub
I bought mine on eBay from e2_shop.
Not sure if the link works but for instance: Brand New OEM O2 Exec/Qtek 9000/MDA Pro Full LCD screen
Broke my screen a couple of days ago.
Im on my way to buy a used universal (need new screen + frame) and I wonder If I will be able to replace the screen + frame without hardresetting the unit. I have downloaded the service manual but I couldnt find any info regarding that. If any one have any useful tips on replacing screen + frame plaese let me know. Do I have to take the phone apart or is it possible to replace screen and frame only by loosing the screen?
Thanks in advance,
Miki
just cracked the screen on my 02 orbit when my daughter sat on it, definately the screen as the screen has a crack line along it and only lights up (can get incomming calles and touch pads seems to respond but only a white screen with lines)..
q1. does anyone know how to take apart an o2 orbit or point me in the right direction
q2. will screens from other phones such as the mda compact or any others work on this phone if i were to buy one or do i need an orbit specific screen.
q3. where i can get a screen from?
thanks guys n girls in advancefor any help you can give as i am now without a phone.
try cpw, the local one to where I work replaces ANY screen for £40 all in
q1. does anyone know how to take apart an o2 orbit or point me in the right direction
Click to expand...
Click to collapse
a1.
http://forum.xda-developers.com/showthread.php?t=298413&highlight=disassemble
If you won't loose your Warrnty so let it repair in an repaircenter.
I have just got my replacement digitizer in the mail 2day from Hong Kong and installed it just now, all is working perfectly as new again. I did a hard reset when the touch screen was first playing up, so I have lost all my themes, settings etc but luckily my office docs etc are still intact.
Anyhow, I made a video on how to replace the touch screen, its only quick as I did not go from the disasembly part, as there is already videos and tutorials on this, so I just documented on the actual digitizer replacement, which is actually basic 2-5mins work, but I thought a vid would be good for any noobs needing it in the future.
Once I edit it all up I will post the video here.
If anyone needs help on replacing the digitizer just ask. DON'T be tricked into buying the LCD + Digitizer if you only need the touch screen, as it is very easy to do without the lcd, though some ppl disagree.
Thanks for reading, thread will be updatd with Vid asap.
Hi X86
I have a crack on the upper plastic case, thats prob. why I have dirt showing on screen. In your opinion where is it located and can I clean it ?
It seems as if (if the crack is on the actual original housing, not just a add-on case) that dirt/dust has fallen down inbetween the digitizer and the LCD, so you can see it through the touchscreen right?
This is fairly simple to fix, you will either need to patch up the crack with silicone or something (best from the inside so it does'nt look messy) OR buy yourself a whole nw housing which cost about US15-$20.
Then just pull your elf/in apart and use cotton tips and wipes to thoroughly clean the LCD and insides.
If you need any help, just let me know via PM or here.
?Good Luck!
Thanks
That was my feeling, now I just need courage to take apart the casing (either repair or replace )
Thanks for bringing up this issue in the forum and extending your hand to others.
I appreciate it alot.
Hi x86
I have read the sticky for disassembling the elf. Can you tell me if it's necessary to unscrew anything and remove the rear speaker in order to remove the front panel ?
Edit: I think I found the answer in the next pics, the 4 screws attach to the front panel, right ?
Hi, i've just entered the world of winmo. i've recently wrecked my Elfin. But i can't seem to figured it out whether it's the LCD or the digitizer is broken...
1) my Elfin's screen turns to white with a few red and black stripes on the lower left corner, it doesn't react to any touch gesture.
2) i can still activesync the device and seems that my SD card is still working, i could copy out my PIMcontacts...thank goodness
3) the alarm still rings the next morning, i assume my device is still operating, of course now i've taken out the battery.
4) i've ask the phone shop for repair enquiries and they said that the replacement parts are not for retail selling in my country, Malaysia... so it needs to send back my Elfin to OEM and takes about 3 weeks time and cost around USD $ 130 bucks....
5) my friends told me it wasn't worth it, thus i was thinking of looking for help online and finally i found this thread...
6) can anyone offer few pieces of info? i thank you 1st.
bjonmy said:
Hi, i've just entered the world of winmo. i've recently wrecked my Elfin. But i can't seem to figured it out whether it's the LCD or the digitizer is broken...
1) my Elfin's screen turns to white with a few red and black stripes on the lower left corner, it doesn't react to any touch gesture.
2) i can still activesync the device and seems that my SD card is still working, i could copy out my PIMcontacts...thank goodness
3) the alarm still rings the next morning, i assume my device is still operating, of course now i've taken out the battery.
4) i've ask the phone shop for repair enquiries and they said that the replacement parts are not for retail selling in my country, Malaysia... so it needs to send back my Elfin to OEM and takes about 3 weeks time and cost around USD $ 130 bucks....
5) my friends told me it wasn't worth it, thus i was thinking of looking for help online and finally i found this thread...
6) can anyone offer few pieces of info? i thank you 1st.
Click to expand...
Click to collapse
That sounds like both a Digitizer and LCD issue.
Red and white strips is caused by the screen, while the phone not sensing your fingers is caused by digitizer.
But you still managed to use something like mymobiler to rescue your stuff right?
Yeah, you're in Malaysia right? In Singapore, to get this items, we have to get it off ebay or dealextreme.com.
But be careful with this, it void warrenty.
If you send it to HTC service centre, it may cost $160> Singapore dollars.
Cheers,
Jeremy