Database Users

somehelp xda2 screen broken need replacement

cmon guys ive been reading this forum for ages and how come there is no answers for getting a replacement screen lcd for the xda2 someone must sell them are they not the same as some sort of ipaq or whatever i have a good orange m1000 with a cracked lcd and want to purchase a new screen but not having much luck the phone is still in good order ie recieves calls and messages and works with activesync but i cant see screen.... sumone help

re:cracked screens
I don't think they sell replacement LCD screens because the cost to purchase would be close to the cost of replacing the phone, not to mention nearly impossible from a maintenance standpoint due to all the minute dis-assembly and PCB connections. I had an XDAII (Siemens SX-56) which had the same problem as yours - screen was cracked and phone still worked but was hard to use with the screen messed up. I ended up buying another unit from someone else so I now have two of them (I use the broken one for spare parts). Just this month I upgraded again to the MDAIII (Audiovox XV-5600) so I can sell you my Siemens SX-56 if you want a replacement unit. Just drop me a note at [email protected].

I can't comment on cost but replacing the Screen is simple. The hardest part is removing the black plastic cover without damaging it or the case.
All that is needed is a very small philips (Jewellers size) a T7 TORX driver and small flat head or similar, to seperate the case.
It's only one ribbon cable to connect the screen to the board but there are 2 different connectors so if you can find a supplier (I'm looking for some of these as well) then make sure that it matches the connector on your board.
These pics aren't that clear and I don't have any screens to show. One is just the plane ribbon cable that slides in the same as the XDA1 the other is a plug and socket.
XDA2 boards

Are you sure about the torx being a T7, I have always used a T6 torx driver.

screen
I had my serial port fixed by www.ppctechs.com and they do screens for $120.

cruisin-thru said:
Are you sure about the torx being a T7, I have always used a T6 torx driver.
Click to expand...
Click to collapse
No, you're right it's T6 but a T7 fits well enough to undo them
The screens ppctechs sell are only the touch screens not the the complete assembly which is what I need.

If you ever find a screen replacement, you can use my guided tour on how to open an XDA2, MDAII...
I've been looking for a replacement housing without any luck... Well, the only place I've found sells the housing for an arm and a leg... They must be joking! :evil:
Good luck!
Rayan

BIG PROBLEM White screen

My screen has gone completely white.... I bought the phone online from an "authorized dealer" who won't reply to me now. I live in the US and O2 does not appear to have any US contact info... Am i screwed on this expensive phone i bought 6 months ago?
Anyone had experience with this?
S

stuart.myers said:
My screen has gone completely white.... I bought the phone online from an "authorized dealer" who won't reply to me now. I live in the US and O2 does not appear to have any US contact info... Am i screwed on this expensive phone i bought 6 months ago?
Anyone had experience with this?
S
Click to expand...
Click to collapse
I guess you already tried hard reset?.
Can you get to bootloader mode?.

Tried hard resets, and getting to bootloader mode, i think this is a malfunction with the actual device, I just need to find out how to get in touch with o2 support internationally, i was wondering if someone on here may have had this problem too.
Thanks.

white screen - connector loose?
I too have this problem - but if I twist the screen away from the keyboard I get the display back. I suspect there's a connector loose inside but haven't looked inside.
Anyone on the forum any experience of getting inside and reseating connectors?

xda operation
tophamn said:
I too have this problem - but if I twist the screen away from the keyboard I get the display back. I suspect there's a connector loose inside but haven't looked inside.
Anyone on the forum any experience of getting inside and reseating connectors?
Click to expand...
Click to collapse
Hello there,
I had to get inside my xda to replace the screen that one of my dear rug rats broke. it is quite easy to do, and you only need to get into the screen side of it to get at the conectors. spin the screen half way round and look at the bottom and you will see 6 small screws. take out the two furthest out and two in the middle nearest the screen side. if you take them all out the whole thing becomes hard to handle. the front cover should GENTLY leaver off, and the cables to it exposed. even if they look in place lift the catch holding them in place and take them out and wipe the contacts with a cloth. just be very carefull with the cable strips as they tear very easy. . any problems then PM me
TTFN
Jay

White Screen
Try www.gpsmidlands.co.uk they replaced my ribbon assembly the same day.

Xda Lcd Repair
Try http://www.pda-repairs.co.uk

Brilliant
thanks for this posting - worked perfectly once i had worked out that atually you need to remove the screws further away from the screen in the middle. but otherwise I have successfully resurected a brick into a working universal! thanks!
Sark

digitizer (touch screen) replacement

Hi guys this is my first post (so please be gentle )
I had a hermes with WM 6 working great until my toddler got his hands on it and now the touchscreen doesnt work (looks like its caused by large dent in the centre of the screen), I've had a look around and found the problem to be with the digitizer itself. I was thinking of replacing it myself with this I found on ebay
http://cgi.ebay.co.uk/ws/eBayISAPI....m=260193961530&ssPageName=STRK:MEWA:IT&ih=016
Just wondering if anyone had purchased one of these and had any feedback as to if they actually work and any tips on fitting it

I would give it a shot as its not to expencive and could save your phone.
I just like the way they bundle in a kit to take the phone apart but ask you to make sure what colour the connectors are on the inside of the phone before purchaseing :-D

thanks for your reply, i may just go ahead and give it a go then, I could post the pictures or a guide if its any use to anyone? Other than that wish me luck (i may need it)

The touchscreen on my Cingular 8525 stopped working today, so I'm faced with a similar dillema. I saw the digitizers for 16-20 dollars online, but I've heard it's safer to just replace the entire screen since you have to seperate the screen from the digitizer with an exacto blade. Either that or I'll have to send it to pocketpctechs and be without a phone for 5 days. Thankfully I can still navigate the phone with the jogwheel + dpad.
I found this video showing how to disassemble your 8525 if you're interested.
http://youtube.com/watch?v=zsljpn74SW0

well just to follow up, the replacement touchpad arrived yesterday it was well packaged and even included a CD containing instructions on how to replace the digitizer itself. I removed the old digitizer (using the edge of a tape measure as it was the only thing i had thin enough) and installed the new one and I have to say im well impressed, all works as it should
A bit of advice though, try and use a soldering iron that is less than 15W as I nearly burned through the contacts but other than that i have my baby back yey

Question about:Replacement of LCD and digitizer and a wierd piece

Hello everyone..I recently replace the lcd for my niki htc...I bought the screen from ebay for $35 (plus shipping). Everything works fine but sometimes when i slide the phone the screen is wably or it looks like something is not connected and it moves but when i close it and i restart it again. it's fine or if i let it for awhile like that (so it goes on and off). So my question is...Is it the manufacture that made the screen, or is it something that it hasn't been connected right?
The other question is that my digitizer is broken in the up left corner and im thinking to replace it does any one can tell me how to take of the digitizer. i have found this website :http://www.pdacenter.ru/razborka/razbor_htc_touch_dual/ but it stops at the screen it doesn't tell you about the digitizer.
And the 3rd question is about that little piece it has fallen from somewhere while i dismantling my phone, i took a picture of it so someone can tell me what it is and where it goes.
Thank you very much for looking, and sorry for the noob questions first timer dismantling a phone and i loved IT!!!

You may wana have a look at the service manual, wich can be found here:
http://www.mikechannon.net/page1.html
It says that you can not disassemble it without replacing the speaker!
When you remove the speaker you need a new one. (or at least this is how I understood it
Maybe that part is the door for the MicroSD Card slot?

no i opened the cellphone 6 to 7 times so far. all you have to do is to unscrew the small screw that keeps the speaker in place so you can have more space to work with it.
all you have to do is to take off the digitiser where it gets connected. take the screen off. and raise the little black strip where the digitizer stripwires come out and push out the digitizer. it feels liked it doesn't go out but if you push it carefully it will. they have glue it with some kind of glue that it doesn't come off the digitizer but it stays on the cellphone so you can put in place your new digitizer...
If anybody needs help... pm me or leave a reply in this thread.

speaker rubber perhaps?
I just replaced my digitizer today (bought the handset from ebay - faulty touch screen). The little rubber that covers the speaker fell out in my hand when I was dismantling mine, so maybe thats what it is (looks similair).
Oh a quick question - after replacing my digitizer, my touch screen still doesnt work, even after hard reset - when asking to 'tap screen to set up device' it wont respond to any taps. Any ideas ?

fubofo said:
speaker rubber perhaps?
I just replaced my digitizer today (bought the handset from ebay - faulty touch screen). The little rubber that covers the speaker fell out in my hand when I was dismantling mine, so maybe thats what it is (looks similair).
Oh a quick question - after replacing my digitizer, my touch screen still doesnt work, even after hard reset - when asking to 'tap screen to set up device' it wont respond to any taps. Any ideas ?
Click to expand...
Click to collapse
my friend i think you have a bad digitizer, some people on ebay send defective digitizer and especially when they are from china they don't really care about sending a good one.... I had to send mine back 3 times!!!! i just got the last one 3 days ago and it took me at least a month and a half to send me a working one...If you pay with paypal...Tell the ebay user to send you a good one...Do not!! Do not!! send feedback until you got a good digitizer....Mostly it has to do with the connectors i guess where the digitizer connects.... Tell them that you need a new one and you can't wait for very long...tell them this is a customers cellphone and you need to have it fixed as soon as possible.. If they don't want to exchange for a new one dispute the payment!!! Don't wait too long...Do it Asap... As i told you there lots of defective digitizers....I had reset mine also but nothing happens i believe this is mostly hardware problem...If you have any questions about how to dismantle ask me... I have open my cellphone over 10 times cause of the digitizer

Thanks Nikos, Im fine with opening these devices they are easy enough to work with.
I purchased a digitizer for a Polaris not long ago and it worked perfect. Im gonna take the Nike apart tonight again and adjust/fiddle with the connections to make sure - I dont want to wait another 2 weeks for a replacement digitizer and pay for postage lol.
But i guess if it doesnt work tonight I will have to 'grin and bear it' and send it back

Just built in a replacement digitizer. Everything works quite well, some inaccuracies in the lower parts of the touch screen, but it works.
I managed to leave over a screw. And a barely visible stain between the Digitizer and the LCD.
But at least it is working again as a replacement phone and for testing various stuff...
btw, now knowing the phone from inside, that part could be the "door" between the SIM slot and battery. or the rubber part that directs sound to the microphone on the bottom front PCB.
cheers

Just fixed my Digitizer

I have just got my replacement digitizer in the mail 2day from Hong Kong and installed it just now, all is working perfectly as new again. I did a hard reset when the touch screen was first playing up, so I have lost all my themes, settings etc but luckily my office docs etc are still intact.
Anyhow, I made a video on how to replace the touch screen, its only quick as I did not go from the disasembly part, as there is already videos and tutorials on this, so I just documented on the actual digitizer replacement, which is actually basic 2-5mins work, but I thought a vid would be good for any noobs needing it in the future.
Once I edit it all up I will post the video here.
If anyone needs help on replacing the digitizer just ask. DON'T be tricked into buying the LCD + Digitizer if you only need the touch screen, as it is very easy to do without the lcd, though some ppl disagree.
Thanks for reading, thread will be updatd with Vid asap.

Hi X86
I have a crack on the upper plastic case, thats prob. why I have dirt showing on screen. In your opinion where is it located and can I clean it ?

It seems as if (if the crack is on the actual original housing, not just a add-on case) that dirt/dust has fallen down inbetween the digitizer and the LCD, so you can see it through the touchscreen right?
This is fairly simple to fix, you will either need to patch up the crack with silicone or something (best from the inside so it does'nt look messy) OR buy yourself a whole nw housing which cost about US15-$20.
Then just pull your elf/in apart and use cotton tips and wipes to thoroughly clean the LCD and insides.
If you need any help, just let me know via PM or here.
?Good Luck!

Thanks
That was my feeling, now I just need courage to take apart the casing (either repair or replace )

Thanks for bringing up this issue in the forum and extending your hand to others.
I appreciate it alot.

Hi x86
I have read the sticky for disassembling the elf. Can you tell me if it's necessary to unscrew anything and remove the rear speaker in order to remove the front panel ?
Edit: I think I found the answer in the next pics, the 4 screws attach to the front panel, right ?

Hi, i've just entered the world of winmo. i've recently wrecked my Elfin. But i can't seem to figured it out whether it's the LCD or the digitizer is broken...
1) my Elfin's screen turns to white with a few red and black stripes on the lower left corner, it doesn't react to any touch gesture.
2) i can still activesync the device and seems that my SD card is still working, i could copy out my PIMcontacts...thank goodness
3) the alarm still rings the next morning, i assume my device is still operating, of course now i've taken out the battery.
4) i've ask the phone shop for repair enquiries and they said that the replacement parts are not for retail selling in my country, Malaysia... so it needs to send back my Elfin to OEM and takes about 3 weeks time and cost around USD $ 130 bucks....
5) my friends told me it wasn't worth it, thus i was thinking of looking for help online and finally i found this thread...
6) can anyone offer few pieces of info? i thank you 1st.

bjonmy said:
Hi, i've just entered the world of winmo. i've recently wrecked my Elfin. But i can't seem to figured it out whether it's the LCD or the digitizer is broken...
1) my Elfin's screen turns to white with a few red and black stripes on the lower left corner, it doesn't react to any touch gesture.
2) i can still activesync the device and seems that my SD card is still working, i could copy out my PIMcontacts...thank goodness
3) the alarm still rings the next morning, i assume my device is still operating, of course now i've taken out the battery.
4) i've ask the phone shop for repair enquiries and they said that the replacement parts are not for retail selling in my country, Malaysia... so it needs to send back my Elfin to OEM and takes about 3 weeks time and cost around USD $ 130 bucks....
5) my friends told me it wasn't worth it, thus i was thinking of looking for help online and finally i found this thread...
6) can anyone offer few pieces of info? i thank you 1st.
Click to expand...
Click to collapse
That sounds like both a Digitizer and LCD issue.
Red and white strips is caused by the screen, while the phone not sensing your fingers is caused by digitizer.
But you still managed to use something like mymobiler to rescue your stuff right?
Yeah, you're in Malaysia right? In Singapore, to get this items, we have to get it off ebay or dealextreme.com.
But be careful with this, it void warrenty.
If you send it to HTC service centre, it may cost $160> Singapore dollars.
Cheers,
Jeremy