USB Sync error msg: Windows does not recognise the device... - JASJAR, XDA Exec, MDA Pro General

Ever since I turned off "Accept all incoming beams" to conserve battery power, and others who have upgraded to the new O2 Exec ROM v1.13.188 (which does this automatically), there seems to be a problem with sync'ing the Universal with the PC via USB with an error message "Windows cannot recognize the device... etc."
A remedy that I found:
1) run the "Wireless Modem" application in Universal (make sure your phone is turned on)
2) select "IR"
3) start and stop the modem
This apparently refreshes the USB, and allows the PC to recognize the Universal again.

Re: USB Sync error msg: Windows does not recognise the devic
heidy said:
Ever since I turned off "Accept all incoming beams" to conserve battery power, and others who have upgraded to the new O2 Exec ROM v1.13.188 (which does this automatically), there seems to be a problem with sync'ing the Universal with the PC via USB with an error message "Windows cannot recognize the device... etc."
A remedy that I found:
1) run the "Wireless Modem" application in Universal (make sure your phone is turned on)
2) select "IR"
3) start and stop the modem
This apparently refreshes the USB, and allows the PC to recognize the Universal again.
Click to expand...
Click to collapse
I have the same problem.
It seems, this problem appears mostly on laptops, not on PCs?
I tried to uninstall\install, repair with all ActiveSync data removal or leaving it - No result.
Also, tried to replace the cable (which is ok, im sure with the one from the camera) - No result.
Temporary and the only way out: do Off\On with qtek9000 on cable connect.
DOES ANY BODY KNOW, HOW TO FIX THIS BUG?? Any Ideas?
Qtek9000 with laptop Toshiba Satellite Pro \ Win XP SP2
EDIT: And, of course, the second workaround - to keep the "Accept all incoming beams" swith ON

are you plugging in via a usb hub? i get this sometimes if i plug in my Exec via a usb port on my monitor. if i plug in directly via the front or back of my pc it generally is ok.
one thing i try is when its plugged in and it gives you that message, turn off the device. it should still be charging. now leave it 10-20 seconds and turn the device on. it then normally "kicks in" for me.
i also find stopping Activesync on the Exec then plugging in the device can get it to work.
theres definately a problem somewhere...
btw i havn't loaded the new rom

i get the problem when I plug in to a hub also, but rarely directly.
if i get it by direct connect, a reset normally rectifies. sometimes i also have reset the pc as well as the ppc

Related

JasJar USB connection problem - please help

I 'suddenly' am unable to have my JasJar connected to Activesync. I have been successfully connecting the last two weeks and did not cahange anything to the PC's set-up.
I killed my antivirus and have no firewall software running.
I have a direct USB connection to my Laptop (no usb hub).
I have tried both Activesync V4.0 and V4.1.
I have deleted all partnerships to get a fresh start.
I have also tried to delete the PPC in the PC's device manager and connect again (I did notice the PPC was listed under the network adapters only, nothing was listed under the USB section).
Nothing seems to help and I am really desperate since I can not sync anything anymore now.
Any suggestions are more than welcome !
Thansk in advance,
Paul
have you tried another PC ? at least this way you can be sure that everything is ok .
I am travelling and will not have any access to another PC before the WE.... I did try another cable but got not lucky..
It does seem to work on another PC.
Anybody any suggestion as to what else I could try to make it work again?
firewall?, thats my pain on my work lappy, i have to vpn into work and that blocks my JJ, i get connecting but no connected, all i can do is disconnect from work which then opens the activesync ports back up. check 7438 and 5679 on your firewall
After a week with AS 4.0 I suddenly found that the only way I could get it to work was to soft reset the Jas Jar while connected. I'm guessing you've already tried that though...
yer, i forgot to say, i can only sync when my JJ has been off for 10+ seconds, if on i get a uab device error if off i connect no problems, this kinda leads me to think that the usb port is in a different mode when on to when on standby, but the usb hosting of devices appears not to be the reason
Carnivor said:
yer, i forgot to say, i can only sync when my JJ has been off for 10+ seconds, if on i get a uab device error if off i connect no problems, this kinda leads me to think that the usb port is in a different mode when on to when on standby, but the usb hosting of devices appears not to be the reason
Click to expand...
Click to collapse
I have the same problem. Get a kind of "USB not recognized" when the jasjar is on/open".
I close the Jasjar after having taken the USB out of course.
Then, after a while ( You say 10 seconds) it works fine and Activesync starts the job.
I can live with it. No soft reset needed.
Very positive to me is the fact that I can also connect to a USB HUB. So no need to plu it directly in my portable.
After connection I can open my little toy. (Gush how I love this thing)
Huib
Yes I have the same problem I only synk when the jasjar is turned off. Most probably one of the reasons apart from firewall issus is office 2003. They said to me from club-imate support that we need the newest office 2003 with sp1.

ActiveSync 4.0 or 4.1 refuses USB connection to EXEC

Dear All,
Please help, my new O2 EXEC is sitting here almost totally useless without ActiveSync.
I did a very stupid thing:
I plugged in the Exec via the USB cable before installing ActiveSync 4.0.
What used to happen (back inthe day 2001 etc) would be that windows would install its own driver for the portable device and then when you subsequently installed ActiveSync its drivers would not go in and hence ActiveSync would not recognise your device.
What is happening now seems like the same sort of issue in that now having installed ActveSync it is just sitting there saying no connection.
For ActiveSync 3.6 and below this is a documented problem and here is the fix
http://support.microsoft.com/kb/264693/en-us
BUT for me this does not work (well because there is no yellow unknown device in Device managers other devices).
In AUDIBLE terms
a) I get a du-duh sound when I plug in EXEC (like if you plugged in a USB key for example)
b) It shows up in the Device Manager-> Network Adapters as "Windows Mobile-based Device"
c) ActiveSync 4.0 or 4.1 does NOT give me the dulde-de-dah sound
d) ActiveSync shows no connections
Anybody any bright ideas? Surely I am not the only twonk to have inadvertently plugged in the EXEC first
Answers greatly appreciated.
BASICALLY HELP
PS: Have also looked at ActiveSync trouble shooter 2001, the ActiveSync 4.0 troubleshooting article from Msoft, tried switching off firewall, no result. Have tried deleting the Mobile-based Device, uninstalling AS 4.0, rebooting, reinstalling AS 4.0 or 4.1 then plugging EXEC,no good.
PPS: I convinced a friend to let me install AS 4.1 on his computer and then plugged in the EXEC and all was fine, so the EXEC itself is sound.
Maybe this will help:
http://www.microsoft.com/windowsmobile/help/activesync/default.mspx
Sorry, didn't read your message good.
Just see now you already did looked at the link....
But another idea: if your device works on your friend PC, then why not
do a clean install for the OS on your own PC?
Maybe this will solve your problem.
Dodger,
Thanks for the thoughts. Well actually thinking about a reinstall of my computer due a moments lapse of concentration is a difficult undertaking. With the backup of the on computer databases as well as over 100 applications installed, I think this would take me several person days.
Currently my thoughts are to clone the partition and then do a windows "over install" onthe clone, but logically that will not work because <of course> the whole point of an over install is that the registry and all applications are preserved.
I spent over 3 solid hours of googling, installing, uninstalling drivers yesterday trying to fix and can't believe I am the only one who has had this problem!
Perhaps somebody with a working ActiveSync can elaborate how does the EXEC show up in device manager (when its plugged in and synced), and also what device driver XP and /or Windows 2003 server would be using.
Thanks mb.
I was facing similar issue. Solution? Yes, uninstall my firewall, connect and sync with my JasjAr and then install the Firewall with Jasjar already connected !
This may help:
Open network connections on ur PC so u can see all connections.
Make sure AS (PC side) is enabled for USB
turn off JJ and plug it in to USB
Turn on JJ whilst watching the window of netwrok connections on ur PC
A new connection icon should pop up, then MAYBE dissapear again
Right click this icon, before it dissapears, and check it's enabled, then select properties
Now check the following items:
- does top box say "windows mobile based device"
- click "configure"
- under configure, is there a button somewhere (mine's working so I can't recall exactly where) that says something like "enable mobile device". If so, then you need to click this.
If this all fails, then repeat but with another USB port. The reason for this seeming waste of time is that you will get a DIFFERENT "Local area connection nn" icon, which may work for you.
I cant believe there hasnt been one mention of rebooting your PC - Which I can assume you already have done?
What OS are you running on your PC?
I have only just got my MDA PRO but this may help! as I did the same thing and for a while XP Pro wouldnt recognise the device.
Uninstall ActiveSync
Reboot PC
Install Activesync V4.0
Plug in USB Device
If there is still a problem connecting you shoudl see a USB device not recognised in your deviuce manager.
It almost seems like there is a time you have to wait before XP will respond normally to you unplugging and replugging in the USB.
Failing this you may have to uninstall Activesync and tehn remove all activesync registry keys it may have left behind! Then reboot and start again!
Just having tisproblem now, this is pïss poor of MS to still be foisting off onto us this Activesync package in such a terible state.
I've just had activesync stop working on me. It would connect but then refuse to sync anything even though it previously worked fine. I think it got upset after I booted up the PC with the Exec connected.
Anyway an uninstall and reinstall of Activesync on the PC cured the problem. Not the most robust software though.
Moandal said:
I've just had activesync stop working on me. It would connect but then refuse to sync anything even though it previously worked fine. I think it got upset after I booted up the PC with the Exec connected.
Anyway an uninstall and reinstall of Activesync on the PC cured the problem. Not the most robust software though.
Click to expand...
Click to collapse
What works for me is to turn off the handheld, and connect the cable after that. Then turn on the device if needed. Works mot of the time then.... no excuse for MS though....

Big ActiveSync Problem

I've bought today a Qtek S200.
IPL/SPL: 2.09.0000
GSM: 2.07.20
OS: 2.9.7.28
The first I did was a Hard Reset to the Qtek S200 and then...
Because of the problems with some application and antivirus I did a complete format to my computer. I just installed WinXP PRO SP2, all the updates from Microsoft Update, .Net Framework 3, Outlook 2002 and ActiveSync 4.1 (both came in the CD from Qtek). (I have also disabled Windows Firewall).
Then I think, I've done all the steps right (I think):
1) I connected the USB cable to de PC
2) I tried to plug the USB cable to the Qtek S200 when te PPC was OFF and nothing happened. Then with the Qtek S200 ON (in today's screen) I plug the other side of the USB cable and ActiveSync does not recognize my S200.
I dunno what to do to make ActiveSync syncronize with my Qtek S200, could you please help me???? I've been trying to syncronize for more then 6 hours (doing all the stuff...)
THNX,
Annita
Try this:
remove your activesync (de-install the software)
reboot your pc
turn on your qtek without the usb cable attached
plugin your qtek on the usb cable.
Does you pc find the device ?? (ding dong sound)
yes ? good, your pc finds it.
take out the usb again
install activesync 4.2
http://www.microsoft.com/windowsmobile/activesync/activesync42.mspx
try again, and see if it works.
My PC does nothing when I connect the S200...
Annita
If the USB cable connection does not work, it is possible to update ROM via Bluetooth ActiveSync syncronization????
THNX,
Annita
Annita said:
If the USB cable connection does not work, it is possible to update ROM via Bluetooth ActiveSync syncronization????
THNX,
Annita
Click to expand...
Click to collapse
It might work, however I would first look into why you usb doesn't work
when you plugin the usb cable, do you see the phone charge ? (led ontop change to orange) you might have a bad cable or you pc has a problem with the usb port (have your tried another usb port ? or removing all usb devices and only using the phone cable ?)
Yes to all.
When I connect the USB cable, the Qtek begins to charge the battery, and the orange led flicks.
I have tried on my PC and on my Laptop and didn't work in any of both.
I have tried with only he USB phone cable and did not work either.
Anyone has tried to update ROM via Bluetooth???
THNX,
Annita
Annita, make sure you have DHCP turned on on your PC. The virtual USB NIC should come up as 169.254.2.2, I believe. I was never able to get it to work without using DHCP on the PC side.
What is the virtual USB NIC????
Annita
When you plug in the USB cable, the PC creates a "fake" network adapter for the PPC and adds that to your list of network connections.
Just make sure DHCP service is started. Right-click My Computer -> Manage -> Services and Applications -> Services -> DHCP Client.
OK, the service was and is ON.
The thing is that I can syncronize via Bluetooth, but not with the USB cable (and I have the original cable and another mini-USB cable).
Annita
Bluetooth Activesync Sycronization will not work b'coz while upgrading, the phone resets itself, N it powers on in the upgrade process therefore, bluetooth of the phone will not be available then.
So, I dont its possible 2upgrade via bluetooth Activesync.
OK, thnx.
Annita
anita and the usb
anita, go to start setting control pannel, go to phones and modems and see the modems are installed there. windows (sh***t) store all the garbadge possible. can be that it identfy usb device like usb modem and put it on com 1 not that active sync works auto on com1. so check connection settings on activesync. + which use port you use? fron pannel or the rear of the PC?
is that a laptop if yes what model.
i'll try to help as much as i can
xman
ok, i have the same problem as you do, or at least a similar. i cant get my sync to work...
active sync 4.2
active sync says "critical communication error, try restarting your device", the active sync troubleshoot tells me that i dont have a ip adress (the link to microsoft does not work), although i have a network connection that my pc created (169.254.2.2). the active sync even appears in green.
my firewall and the win firewall does not interfere with this. switching off the firewalls does not improve this at all.
does anyone know a solution to this? thanks
I'll try what xmanmaster says, but I'm not at home until sunday...
Thnx,
Annita
Did this problem ever get resolved? I have the same issues, tried a wizard and a hermes. Not detected as a usb device, the charging light comes on. Both phones work on another PC. I have tried uninstalling activesync and rebooting phone/PC in every order I can think of.
UPNP (Universal Plug 'n Play) service is required
Hi all,
please make sure that the UPNP service is running on the desktop.
It's required for device detection as well as synchronisation with the WCE device.
A quite detailed description of all potential problems with ActiveSync can be found at Chris De Herrera's website.
BR,
N.a.D.

Big Problems :((

I have the following problem with my HTC Touch HD. Since yesterday after i transfered 2 video files and a few pictures, when i connect it through USB, the computer doesn''t detect HTC anymore (nor syncing nor file transfer). Even the Bluetooth syncing does not work. I performed several soft and hard resets, and it seems it;s getting worse after every reset.
I bought the phone 2 weeks ago, after i sold my Apple iPhone 3G 8GB. As we speak, i kind of regret i did that...any advise for me ?
I forgot to mention: when i plug the uSB cable, the device goes recharging.
Have you tried booting your pc ?
Also try unchecking Settings/connections/Usb to Pc/ "enable faster data synchronization"
r
Andrew
What cable do you use? I had similar problems with non original (asus) usb cable.
greetings everybody..
1) i tried what you said several times, no result.
2) i get same results with the original and the other cables..
3) i noticed one thing . . . if i connect the device to a computer that i never conected before the device, it launches active sync....and Active Sync just wont interact with my device.
Did you try reinstalling ActiveSync on your PC?
yes i tried....same result. Do you think a change of ROM would solve that ?
Now, even a syncronisation using bluetooth is almost impossible, since i cant pair the computer and the device. Damn, it's like a virus or something.
stupid thought:
Do you think a change of ROM would solve that ?
Click to expand...
Click to collapse
Impossible since i cannot connect using USB. Sorry !
I too had problems with my PC not recognizing the HD. Found out that it was a problem with my firewall and anti-virus. I adjusted anti-virus settings to allow active sync to pass through and have had no problems after that.
HTC also recommends going to Start --> Settings --> Connection tab --> USB to PC and deselect the checkbox for "Enable faster data sync"
For device recharging when plugged in to USB : go to Start --> Settings --> System tab --> Power. here below the battery charge indicator, there is a checkbox. Read the message and check/uncheck as desired.
Hope this helps !!
i thought one potential source for my problem would be the antivirus, but i disabled firewall (eset at work and symantec end point protection at home) and no result what so ever.
I cand figure a way to sync the device even with the bluetooth since i cannot pair the device and the computer.
I am starting to regret i bought HTC...
Try click the Activesync icon on HD Program, there is a "Option" on the menu, click and see if you could delete all the old connect. If yes, re-establish the connection again to see.....good luck
Option menu item is disabled (i performed several hard resets)...(
Another thing i noticed. I unchecked the box (when connected to USB charge), so now when i plug the usb cable, it wont charge. But, if the device is in stand by (black screen), and i plug the usb cable, it wakes the device up. So, in my mind, i think it is something wrong with the OS, it still "feels" the USB cable, but cannot (for an unknown reason) take the necesary action.
For 4 hrs i try to sync the device with the computer using bluetooth, and i cannot manage to do so.
Is there any way to reinstall ActiveSync on my HTC device ?
daemonus said:
Option menu item is disabled. For 4 hrs i try to sync the device with the computer using bluetooth, and i cannot manage to do so. Is there any way to reinstall ActiveSync on my HTC device ?
Click to expand...
Click to collapse
My sync problem with HD and my PC with Vista, was solved as follows:
- Uninstall Windows Mobile Device Center
- Reboot and reinstall WMDC
Ton V
NLBeev said:
My sync problem with HD and my PC with Vista, was solved as follows:
- Uninstall Windows Mobile Device Center
- Reboot and reinstall WMDC
Ton V
Click to expand...
Click to collapse
Tonight i will try to install at home Windows VIsta (at work and at home right now i have XP). I cannot use my phone - no phone number in agenda and it's driving me mad. The phone rings and there are quite a few persons i dont want to talk with.. HEEEEEELP
nobody there to help me ?
If you did a hard reset, and you can connect in drive mode, but can not sync, then I am 99.9% sure that there is nothing wrong with your phone, but that your computer is messed up.
Uninstall all your antiviruses, firewalls, and other bloatware, and see if it works then.
Just a possible solution, but did you try plugging in your phone into other USB slots on your PC? Are you perhaps trying to sync it through an USB extension cord, or maybe USB hub? I had problems with my PC recognizing the THD if I tried syncing that way. Best results were plugging it directly into the back side of the casing.
The reason I'm asking this is that if you have too many USB devices plugged in, it's possible that the USB voltage drops too low and devices won't connect to the computer.
I tried on 5 different computers, all available USB ports.
On a new computer, sometimes on the device screen it shows up Active Sync but that is all, no sync occurs. If i try again on that computer, i get the same result as i get using the computer at home or work.
The device cannot conect as a Disk Drive
Is there a way to reinstall Active Sync on HTC ? My guess is that this software is all gone with the wind (even i performed a hard reset). The big question is what the hell happened ? Could be a ROM fault ? I mention i never tried to change ROM, the only software i installed was S2U2 and Core Player.
If by monday it wont work, then i'll send it into service (i have warranty). But i hate service
all out of ideas...
Any ideas ?
Which items are checked when you go to Settings/connections/Usb to Pc/ on youre phone?
Have you tried to use another memory card (because youre problems started with copying)?

mobile device center (Vista) & HTC Pro 2

I recently had to replace my notebook, new one came with Vista, also coincided with purchase of Touch Pro 2.
my current kaiser (WM 6.0) works fine, connect usb, vista fires up mobile device center.
connect pro 2 (WM6.1) via usb , nothing, device center does not start up.
run active sync on the pro 2, Sync button is grayed out. I have set 'sync all pc's....' to usb in the connections screen.
have checked other threads but so far come up blank.
can anyone point me in the right direction to possible fixing this, I need to reload some software not to mention I would like to and would like to check out some of the roms on this sight.
chrisnz1947 said:
I recently had to replace my notebook, new one came with Vista, also coincided with purchase of Touch Pro 2.
my current kaiser (WM 6.0) works fine, connect usb, vista fires up mobile device center.
connect pro 2 (WM6.1) via usb , nothing, device center does not start up.
run active sync on the pro 2, Sync button is grayed out. I have set 'sync all pc's....' to usb in the connections screen.
have checked other threads but so far come up blank.
can anyone point me in the right direction to possible fixing this, I need to reload some software not to mention I would like to and would like to check out some of the roms on this sight.
Click to expand...
Click to collapse
Have you tried starting mobile device center manually? Also had some troubles now and then, reboot of my pc and softreset of my phone usually fixed my problems. Else most responses will probably include the usual: remove all partnerships and/or reinstall mobile device center.
Btw, does your device show up in your hardware list or under my computer when connect it to your USB port?
mobile devioce center (Vista) and htc pro 2
have tried pc reboots and htc reset, no go.
If i connect my kaiser it appears as a device under my computer and device center picks it up.
connect the pro 2, does not appear as a device under my computer and if device center running does not attempt a connect, if device center not running vista does not start it
also no partnerships currently set up.
did have a kaiser one , deleted this when the pro 2 did not connect
chrisnz1947 said:
have tried pc reboots and htc reset, no go.
If i connect my kaiser it appears as a device under my computer and device center picks it up.
connect the pro 2, does not appear as a device under my computer and if device center running does not attempt a connect, if device center not running vista does not start it
Click to expand...
Click to collapse
Well as far as I know Windows should at least show your device under My Computer, even without a partnership or without even having Mobile Device Center installed.
So my best guess is there is some conflict which prevents your TP2 from even connecting to your notebook. Have you tried connecting it to a desktop PC? Or are you trying to connect it through an USB hub or something? If so it is possible the hub isnt delivering enough power.
I had the same issue and ending up hard resetting my phone before I figure what I did wrong. Go to settings on TF3D then all settings. Go to connections, and under usb to pc, select active sync. If it says disk drive it will not work in active sync. Also if the enable faster data sync is checked...uncheck it. Sometimes this causes an issue.
Go to settings and choose USB->PC Settings. Here you can disable "fast synch". Now it should work, if not, activate "fast synch" ^^
YOu might want to re-instal active sync ( device center ), I had a simulair problem, and it was solved
gz reb3lzrr
rodium and vista sync
firstly thanks for the many replies.
still no go
reinstall device center
rebooted pc, reset phone.
tried with a xp laptop with active sync, still no go.
neither pc recognises the rodium phone.
when I attach my kaiser each pc 'chimes' , ie recognises the attachment and activesync or device center start up and connect
rodium nothing.
tried each of the usb ports and couple of cables, all work for kaiser non work for rodium.
Hi. I have had the same problems. Disable fast sync like my man neonoxDE said. That will help you. Altough it helped me. With Win7 you can sync with that option enabled.
(QUOTE: Go to settings and choose USB->PC Settings. Here you can disable "fast synch". Now it should work, if not, activate "fast synch" ^^)
thanks tried that as well, still no joy.
Its has if the phone is not telling the op system that its there. Ie the interupt to the op system that happens when a usb device is attached is not happening, or being ignored.
i had the same problem. i had to uncheck the box advanced network funtions. that wen you go in to settings and usb to phone.
that was the problem with my phone sync.
sorry for bad english.
Ugh
Just went through this all tonight. Also coming from a Kaiser (AT&T Tilt).
To get it functional, I had to:
1.) Add Remove Programs
2.) Remove Windows Mobile Device Center
3.) Remove Windows Mobile Device Center Driver Update (if you installed it).
4.) Disconnect USB from phone.
5.) Reboot
6.) Reinstall Windows Mobile Device Center 6.1 from CD (Sprint here).
7.) Install Windows Mobile Device Center Drvupdate. (WMDC dir on Sprint CD, called drvsomething or other, depending on if you're 64 bit or x86 on your PC).
8.) Then had to "Clear Storage" on the phone and let it clear itself (a simple reset did not let this work)
9.) Once soft reset was completed, I could connect the phone, it then found it, and worked correctly.
Yeesh.
Unchecking the box everyone is saying didn't have an effect for me, though I tried it many times before going all nuclear.
Thanks for this.
Tried this on my vista laptop still no go.
If I connect my kaiser 'installs device driver software' pop up displays and when this is finished windows mobile device center starts up.
Initial connection of pro2, nothing
After having the pro 2 connected for at least 45 mins I did get an an install device driver message, the device was unknown and device center did not start up.
so it appears that the pro2 was recognised has an unkown device
additional info
loaded down a usb moniter onto my laptop.
When I plug in the Kaiser usb monitor shows connection of the device on the specific port.
Unplug this and plug in the PRO2 onto the same port nothing shows as being connected.
rapidlycomming to the conclusion problem with the data pin outs on the USB, does anyone know of a diag program that could test this out or an easy way to check this.
save me the initial cost of checking by a repairer (which in the UK can be steep)
Although my TP2 will sync with USB, most of the time I sync via a bluetooth connection.
Have you tried doing it that way?
Maybe this will work.
One unconventional way to fix this, is to go to your phones activesync. select menu, then change it to bluetooth sync. After that, soft reset phone and connect via usb.
Windows Update
Try conducting a Windows update manually when your phone is connected via USB cable.
Cheers
andrew-in-woking

Categories

Resources