Database Users

JasJar USB connection problem - please help

I 'suddenly' am unable to have my JasJar connected to Activesync. I have been successfully connecting the last two weeks and did not cahange anything to the PC's set-up.
I killed my antivirus and have no firewall software running.
I have a direct USB connection to my Laptop (no usb hub).
I have tried both Activesync V4.0 and V4.1.
I have deleted all partnerships to get a fresh start.
I have also tried to delete the PPC in the PC's device manager and connect again (I did notice the PPC was listed under the network adapters only, nothing was listed under the USB section).
Nothing seems to help and I am really desperate since I can not sync anything anymore now.
Any suggestions are more than welcome !
Thansk in advance,
Paul

have you tried another PC ? at least this way you can be sure that everything is ok .

I am travelling and will not have any access to another PC before the WE.... I did try another cable but got not lucky..

It does seem to work on another PC.
Anybody any suggestion as to what else I could try to make it work again?

firewall?, thats my pain on my work lappy, i have to vpn into work and that blocks my JJ, i get connecting but no connected, all i can do is disconnect from work which then opens the activesync ports back up. check 7438 and 5679 on your firewall

After a week with AS 4.0 I suddenly found that the only way I could get it to work was to soft reset the Jas Jar while connected. I'm guessing you've already tried that though...

yer, i forgot to say, i can only sync when my JJ has been off for 10+ seconds, if on i get a uab device error if off i connect no problems, this kinda leads me to think that the usb port is in a different mode when on to when on standby, but the usb hosting of devices appears not to be the reason

Carnivor said:
yer, i forgot to say, i can only sync when my JJ has been off for 10+ seconds, if on i get a uab device error if off i connect no problems, this kinda leads me to think that the usb port is in a different mode when on to when on standby, but the usb hosting of devices appears not to be the reason
Click to expand...
Click to collapse
I have the same problem. Get a kind of "USB not recognized" when the jasjar is on/open".
I close the Jasjar after having taken the USB out of course.
Then, after a while ( You say 10 seconds) it works fine and Activesync starts the job.
I can live with it. No soft reset needed.
Very positive to me is the fact that I can also connect to a USB HUB. So no need to plu it directly in my portable.
After connection I can open my little toy. (Gush how I love this thing)
Huib

Yes I have the same problem I only synk when the jasjar is turned off. Most probably one of the reasons apart from firewall issus is office 2003. They said to me from club-imate support that we need the newest office 2003 with sp1.

ActiveSync 4.0 or 4.1 refuses USB connection to EXEC

Dear All,
Please help, my new O2 EXEC is sitting here almost totally useless without ActiveSync.
I did a very stupid thing:
I plugged in the Exec via the USB cable before installing ActiveSync 4.0.
What used to happen (back inthe day 2001 etc) would be that windows would install its own driver for the portable device and then when you subsequently installed ActiveSync its drivers would not go in and hence ActiveSync would not recognise your device.
What is happening now seems like the same sort of issue in that now having installed ActveSync it is just sitting there saying no connection.
For ActiveSync 3.6 and below this is a documented problem and here is the fix
http://support.microsoft.com/kb/264693/en-us
BUT for me this does not work (well because there is no yellow unknown device in Device managers other devices).
In AUDIBLE terms
a) I get a du-duh sound when I plug in EXEC (like if you plugged in a USB key for example)
b) It shows up in the Device Manager-> Network Adapters as "Windows Mobile-based Device"
c) ActiveSync 4.0 or 4.1 does NOT give me the dulde-de-dah sound
d) ActiveSync shows no connections
Anybody any bright ideas? Surely I am not the only twonk to have inadvertently plugged in the EXEC first
Answers greatly appreciated.
BASICALLY HELP
PS: Have also looked at ActiveSync trouble shooter 2001, the ActiveSync 4.0 troubleshooting article from Msoft, tried switching off firewall, no result. Have tried deleting the Mobile-based Device, uninstalling AS 4.0, rebooting, reinstalling AS 4.0 or 4.1 then plugging EXEC,no good.
PPS: I convinced a friend to let me install AS 4.1 on his computer and then plugged in the EXEC and all was fine, so the EXEC itself is sound.

Maybe this will help:
http://www.microsoft.com/windowsmobile/help/activesync/default.mspx

Sorry, didn't read your message good.
Just see now you already did looked at the link....
But another idea: if your device works on your friend PC, then why not
do a clean install for the OS on your own PC?
Maybe this will solve your problem.

Dodger,
Thanks for the thoughts. Well actually thinking about a reinstall of my computer due a moments lapse of concentration is a difficult undertaking. With the backup of the on computer databases as well as over 100 applications installed, I think this would take me several person days.
Currently my thoughts are to clone the partition and then do a windows "over install" onthe clone, but logically that will not work because <of course> the whole point of an over install is that the registry and all applications are preserved.
I spent over 3 solid hours of googling, installing, uninstalling drivers yesterday trying to fix and can't believe I am the only one who has had this problem!
Perhaps somebody with a working ActiveSync can elaborate how does the EXEC show up in device manager (when its plugged in and synced), and also what device driver XP and /or Windows 2003 server would be using.
Thanks mb.

I was facing similar issue. Solution? Yes, uninstall my firewall, connect and sync with my JasjAr and then install the Firewall with Jasjar already connected !

This may help:
Open network connections on ur PC so u can see all connections.
Make sure AS (PC side) is enabled for USB
turn off JJ and plug it in to USB
Turn on JJ whilst watching the window of netwrok connections on ur PC
A new connection icon should pop up, then MAYBE dissapear again
Right click this icon, before it dissapears, and check it's enabled, then select properties
Now check the following items:
- does top box say "windows mobile based device"
- click "configure"
- under configure, is there a button somewhere (mine's working so I can't recall exactly where) that says something like "enable mobile device". If so, then you need to click this.
If this all fails, then repeat but with another USB port. The reason for this seeming waste of time is that you will get a DIFFERENT "Local area connection nn" icon, which may work for you.

I cant believe there hasnt been one mention of rebooting your PC - Which I can assume you already have done?
What OS are you running on your PC?
I have only just got my MDA PRO but this may help! as I did the same thing and for a while XP Pro wouldnt recognise the device.
Uninstall ActiveSync
Reboot PC
Install Activesync V4.0
Plug in USB Device
If there is still a problem connecting you shoudl see a USB device not recognised in your deviuce manager.
It almost seems like there is a time you have to wait before XP will respond normally to you unplugging and replugging in the USB.
Failing this you may have to uninstall Activesync and tehn remove all activesync registry keys it may have left behind! Then reboot and start again!

Just having tisproblem now, this is pïss poor of MS to still be foisting off onto us this Activesync package in such a terible state.

I've just had activesync stop working on me. It would connect but then refuse to sync anything even though it previously worked fine. I think it got upset after I booted up the PC with the Exec connected.
Anyway an uninstall and reinstall of Activesync on the PC cured the problem. Not the most robust software though.

Moandal said:
I've just had activesync stop working on me. It would connect but then refuse to sync anything even though it previously worked fine. I think it got upset after I booted up the PC with the Exec connected.
Anyway an uninstall and reinstall of Activesync on the PC cured the problem. Not the most robust software though.
Click to expand...
Click to collapse
What works for me is to turn off the handheld, and connect the cable after that. Then turn on the device if needed. Works mot of the time then.... no excuse for MS though....

Jam not recognised by windows/activesync

Hi Guys,
New to the ppc scene, so please be gentle!
I've had a search through the forum, and can't find the answer to my problem, so please help me, if you can.
I have just been given an imate jam by my dad, his old work phone. It hasn't been used for approximately 6 months, so I had to charge the battery (and back up battery) to get it up and running.
Now I've got it charged up and switched on I've encountered a problem:
When I connect my Jam to my PC (XP Pro) it lights up the charge LED but then nothing, no installing drivers or anything. When I start activesync it doesn't see the Jam, when I go to device manager on my pc it's not there.
The Jam has also reset itself a few times, so I was thinking I should upgrade/reflash the software - but I can't do that when the PC doesn;t see the Jam.
Have I missed something, done something stupid or is the Jam knackered? Any help would me muchos appreciated
Many thanks in advance.

My device is an imate jam, details below:
ROM Version: 1.03.00 WWE
ROM Date: 11/01/04
Radio Version: 1.01.00
Protocol Version: 1337.38
Ext ROM Version: 1.03.163 WWE
Not sure if this helps anyone help me with my problem, but thought the more information the better!
Thanks in advance for you help

Check your connection settings in ActiveSync.

Ok, I've just tried the settings you suggested, though for some reason I can only select COM4?? I'm using activesync version 4.1.4841.0
When I try and connect I get the error shown in the attached image

Although some have had luck with AS4.x, others as well as myself have experienced that it doesn't work very well with the Magician. Use AS3.8 and it works flawlessly.

ok, I've changed to activesync v3.8 and still no joy - it just goes in circles looking for the device on COM4
I'm showing:
COM1 Not Installed
COM2 Not Installed
COM4 Available
Infrared Port Not Installed
USB USB is Available
This is driving me crazy!!

Normally when the magician is plugged in to the usb port, windows should recognize this and go through the usual driver installation procedure. If not disconnect the magician, switch off all settings in AS and reboot your PC. After the PC has booted and you logged-in, connect the magician to a different usb port. If the windows plug+play install routine does not appear, go to control panel and add the device manually. Once the device is added, then put back your settings in AS.

ok, 2 reboots later!!
when I connect it (on a different port) all that happens is the LED goes Orange to indicate that its charging - no drivers are installed.
When I go to Add Hardware it can't find the Jam (tried changing the port) and if I go to device manager its not there (not even with a ! Warning next to it).
I'm now trying to add it from a list, but I can't find imate or HTC in the list of manufacturers.
I'm totally stumped, this is insane!
Any more ideas?

Try hard resetting the magician then check AS settings in the magician also.

I've done a hard reset and rebooted my pc again, still nothing, even when I try and add it manually.
I've even tried connecting in bootloader mode, but that won't work either!
Could it be a hardware fault? Or more likely a software thing?

Not being recognised
Hi
I had the same problem today, it turned out to be a faulty cable(brand new spare). I used a different cable and all is good.
:wink:

I've now tried 3 different cables, 2 latops and a desktop PC and am having the same problem no matter what - I reckon my Jam's screwed up somehow!

Take a look on the connector, try to clean it(with alcohol preferably and with battery out of jam). You have to have AS installed before you connect the jam to pc for the first time, otherwise it will cause problems. Did you try BT connection to active sync? Did it work? Did your dad experience these problems too?

Ok, there's definately a problem with my device.
I can pair it up via BT and transfer files etc, but as soon as I connect with Activesync I get the same error message as I posted earlier in this thread.
I've tried cleaning the mini-usb port (battery out) with alcohol, still no joy.
Spoke to my dad, says he never used activesync, just used it as a phone and a sat nav, nothing more.........
Starting to get really wound up by this now. Unless anyone has any other ideas (dropping it from a great height??!!) I think I'm gonna have to send it to a repair centre for them to have a look at it

i had an intermittent problem like this wherw windows would say a USB device connected to the system was malfunctioning etc..
It cleared up after a while donno why... when uve connected the JAM, wiggle the connector around a bit and see if anything happens....

The message you get is not necesarilly caused by faulty device, I got that message many times before I was able to properly configure my active sync over BT.

the cable supplied with imate jam looks like a normal mini usb cable but its not.
its different then the mini usb cable. You cant use a mini usb cable (from ur camera,card reader etc.) with your imate jam.
Once I used my camera mini usb cable with imate jam and i got the same error which omhaigh is having. Netither Windows recognize my imate jam nor activesync. I plugged in my imate jam cable and it was all good again.
In short, you need cable supplied with imate jam to connect it with pc.

The Magician's USB cable is a standard one. I've been using various USB cables on my laptop. home desktop, and office PC without any problems.

yeah, it is completley standard, ive used 5 different cables and all work,

I've now tried a whole host of PC's and Laptops at work, using several mini usb cable and bluetooth (both built in and dongle on different machines) following the advice above and in the BT active sync thread.
No matter what I do (including cleaning the ports with alcohol etc) I get no joy what so ever, and always end up with the same result!!
I've read that connecting the device to a pc before installing activesync can cause problems.......I'm starting to think that perhaps my dad's done that and either can't remember or is too embarrassed to admit it! Is there a fix if this is what has happened?
I'm guessing its gonna have to go to a repair centre

qtek 9100 internet through usb?

can anyone explain how can i connect the mobile through internet via usb cable? on pc I have connection. i need on mobile. waiting for a reply. thanks

After you installed ActiveSync it should work automatically when ever you connect the WIZ via USB cable to the computer - at least it works on mine! No further steps necessary, except turning off GPRS and WLAN.

for my phone it doesnt work like that i think i have to make some settings or something..
i resolved the problem. i needed to add
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services]
"AllowLSP"=dword:00000000

[Q] ActiveSync 4.5 not starting

Hi Gents,
Just bought HTC HD mini (WM 6.5). Tried to connect to my laptop (running WinXP SP3) via ActiveSync 4.5 but nothing happened.
Firewall is opened for ActiveSync and all other possible rechecks which found on other forums were done.
Nothing...
Any ideas?

In Settings-More-Connections-USB to PC disable Fast data sync.

Done.
Nothing changes...

Make a soft reset and deactivate any firewall or/and antivirus from your pc.

fighter7139 said:
Make a soft reset and deactivate any firewall or/and antivirus from your pc.
Click to expand...
Click to collapse
Still nothing, but on HTC Task Manager ActiveSync is shown as Mem 932k CPU 0%.

Have you tried all the USB sockets on the PC? Mine will only connect to a Dell PC at work on the sockets at the rear of the PC, not the front mounted ones.
I think it is a power issue, IE not enough power is available from the front sockets. Though I could be wrong...

In ActiveSync you'd enable the USB-port And, when your device is connected into USB, you'd select "ActiveSync Sync with outlook" on your device. To be able to select that option you have to unlock your device. Good luck

Udated ROM to 1.36.479.1 then successfully synchronized at home where I have Win7. After connecting at work with WinXP SP3 via ActiveSync 4.5 all runned well.
But now my HTC HD mini can't find bluetooth headset Sony Ericsson HBH-DS205 which before ROM update work well. Other bluetooth devices are shown but not bluetooth headset Sony Ericsson HBH-DS205.

Clear now... Just was necessary to reset headset.