Could someone tell me how to upgrade my MDA just with USB cradle.
I tried SDcard upgrade, but SD slot on my MDA is dead
I need other way for upgrade. I dont have ROM in MDA now.
GSM Radio stack is OK, so I need just WM2003 ROM upgrade.
Please help me! I am absolutely down with this problem:-(.
(bootloader is OK - 5.15 version).
Related
I upgrade my ROM to Pocket PC2003 (T-mobile.nbf) image that worked with no problems using the XDA OS Image tool. It copied over using programme A and following the upgrade I carried our a Radio Stack upgrade to 4.21 supplied by O2. I now have a problem as the phone wont work. I tried re copying the immage again but just before programme A runs a cmd.exe box apears and I get the following message 'ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host.
error getting connectiontype
Programme A then tells me my device is not connected and to check the USB connection. Can any body please help me. All I want is to get my XDA phone up and working again.
Which network are you using, it may be that the bandswitch has chosen 900/1900 which would prevent orange and t-mobile from working, if this is the case enter bootloader, then push the key below the antenna, choose 900/1800 then reboot.
I'm on the O2 (pay as you go) network. There were no problems with my phone and the T-mobile image until I performed the O2 Radio Stack upgrade. I hade already performed this upgrade on my old operating system, before I copied over the T-mobile image. I had no problems with the old OS and the Radio Stack upgrade.
Seamus, if you burn the original O2 rom back to the phone, you will be able to return it to O2 if it is the radio stack upgrade that killed the phone, they should fix it for free.
Hello guys Need some help from the pros
I currently purchased this phone its a Siemis Sx56 AT&T. As i was updating 2 unlock the phone with a dump of another sx56 aT&T that was uncloked (via sd card) it stop in the middle of the proces of uploading the boot of the sd card. Now the phone:
1. Will not start
2. Can not boot the phone to wallaby
3. cooked a rom and tried 2 boot 2 wallaby with no luck
4. 1/2 read & read with no way of knowing what i'm doing wrong
5. how can i repair my bootloader (I used the one in xdtools with no luck)
Than U guys in advance
Luv the Info in the forum.
Adrian
Atlanta GA USA
I recently bought a german QTEK S200 and upgraded to latest Dopod ROM that is available in ftp.
I used lokiwiz and awizard tools to return to an older JAMin ROM that did not work as you very well expect.
Than I realized that I am unable to hardreset or put the jamin in bootloader mode. I am sure that before ROM upgrading I was able to do so; but I am not sure when the problem started. I mean whether it happened before using above tools or not. I am able to upgrade with dopod ROM one after another that makes the device enter bootloader and hard reset afterwards but manually I can not.
The cam and conn man buttons and soft reset all work alone but not in combination. I tried to wait for 5 to 10 sec before I take the stylus out of the hole but nothing changed. Aso the exe file enterbootloader is under windows and when I click it the device enter bootloader. Any comments?
Also is there a chance to have a QTEK German ROM with AKU 1. If so I will try the assumed but not proven method to downgrade to a lower ROM with prophet (which worked with wizard with a custom ROM).
Cheers.
After flashing the same Dopod ROM one after another the device started to enter bootloader :shock: and after a few more flashing the device can be hard reset as well. 8) No need to tell that I very happy
Bootloader mode in PROFHET (JAMin,S200 etc)
Hi ppl.
I suggest you to use cradle with 5V (1A) original charger or give 5V voltage to device externally.
By the way: to get prophet in Bootloader mode u need to hold continuously Cam and Power buttons.But u should do this with 5V (1A) voltage.
Thats all.
Neither with USB cable nor with the external supply the device does not enter bootloader mode by your method.
Also known method (cam button + reset) does not work with external supply as well.
Unable To Hardrst And Put In Bootloader The Prophet
Im not sure if this helps anyway i assume you can get to the OS executing EnterBootloader from an SD card or device memory did take me to the tricolour screen. on an SPV M600
Hi...
I upgraded my qtek 9100 from OS version 1.6.7.1 to cingular 1.8.11.1
The problem is that now, the phone doesn't start... the splashscreen appeears, along with... IPL 2.17
SPL 2.21
GSM 02.07.10
OS 1.8.11.1
But doesn't get out from there...
Did a do anything wrong?
PLEASE help me?
Is there any solution or is it bye bye qtek?
maybe you flashed broken or wrong rom.
start your device in bootloader mode (look in wiki how to do this) and then reflash again and if this does not work, get rom from your provider and reflash with this.
...
But my pda starts and it stays in splashscreen... is it repareble anyway?
Yes it should be fixable
Cant understand why you would want a old cingular rom (the cingular is not exactly same hardware as your phone wiza200 vc wiza100!)
You should download an aku2 rom here ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
user name xda password xda
Next get into the bootloader screen - turn device off and start with camera button pressed - should be a multicolor screen
Next attach device to pc via usb cable
Flash with above rom and all should be well
help me to break & solve this problem, maybe can also help the other members..
I tried to upgrade my XDA to WM2003SE everything goes right,
bootloader first time i still use v5.22
but when I soft reboot it freezes on the OZUP screen and
message ONLY FOR MICROSOFT bla bla bla....
i get this ROM from http://www.romkitchen.de/ ==> WM2003SE
then downgrade bootloader from v5.22 to v5.15,
using MMC (flash SD) continue to special rom 1.2,
and then cooked again using PC2002 by my own creation based from
romkitchen, what i want to ask is :
i cannot connect again via dekstop activesyn if i want to change
my ROM because my cradle cannot detect my charger?? but if i charge
directly, its work. What is the problem?
is my cradle/dekstop broken at the charger socket?
so what i need to do? just change the wire or socket or
i use the step like at http://wiki.xda-developers.com/index.php?pagename=WallabyCradleMod
if i prefer use the 2nd method, is that really OK? so just used cradle/deskstop, no need
power charger again if i want to change ROM to WM2003SE, because only can use via activesync?
after i change bootloader to v5.15, keep trying to change but only can via Flash SD Card,
i change to WM 2003 final, still same problem....after finish, only screen cannot enter the
menu or else, only boot screen until i am waiting for 15 minutes??? then change again to
WM2003 but using from http://www.romkitchen.de/tools, still same again....boot screen again...
haiyaaaa.....what happen?? i dont know, tired, always overtime to do this,hehehhee...
all my friends, help me...need your advice ^_^V
*now, i still used ROM from PC 2002,cooked again using PC2002 by my own creation based from romkitchen.
bootloader v5.15
Microsoft Pocket PC --> PC2002
Version 3.0.12039 (Build 11178)
ROM version : 3.17.03 ENG
ROM date : 05/15/03
Radio version : 6.24.00
Protocol version : 324e4
Model No.: PW10A1
I can not really help you, but i was also in the same situation, that i have had a device, that doesn´t work with any other ROM than PPC2002
Flashed several WM2003 ans the WM2003SE but non of them worked.
So i rest at PPC2002
Stefan
ow ow...
auch.. ok, thanks for the comment, i give-up,hehehe..but only for now,
take a rest first but i dont know for t'mrow, actually from 10 flashed,
i got 1 success, can got WM2003SE but with almost empty battery,
i know the inside and already set all, including i notice bluetooth icon,hehehe..
but how? i wonder that my sx56 with fake bluetooth, only icon
but after i charge my sx56 then i soft reset, its gone, back again with only boot-screen, after that, i can't find again WM2003SE ROM only lock with boot-screen, and ONLY FOR MICROSOFT..blablabla...
and about for my cradle/dekstop? how is it? can u give me solution to fixed it??
btw,thanks for helping, tips & trick hehehe...
i will keep trying to find/solved this problem by my own way ^_^V
modify my cradle/dekstop success
its working, i try to modify my cradle/dekstop with that steps (look at the top this thread), and it's work...actually not me who did it, but my friend,hehehehe....i ask his help and he agrre to doit, but all the risk is still at me, now i can charge and also syncronized to my notebook
hy. i'm a newbie so plz escuze my mistakes and most of all my english.
i have a mda vario or htc wizard 200 as i know.
on the start screen,it shows
IPL 1.06
SPL 1.06
GSM 01.12.10
OS 1.6.2.1
it's a G3 wizard. My problem is that it has the T-Mobile original german ROM and i want it in english. i have read most of the forums here and tried many ideas i found here but nothing helped me so far... i tried cid unlock with lokiwiz,it shows me that is unlocked but when i try to flahh it with the .exe flasher,downloaded Rom-s for it from here,it's not working. I have Win7 now and i tried with Windows mobile device center sync software for win7 and nothing,i tried in Win xp with activesync and nothing,the same simpthomes. It syncs,detects my ppc,i start the RUU,detects the Rom i have,but when i get to the flash window,just after it tells me that the flash process will take about 10 minutes,my ppc disconnects,enters in the bootloader mode,connection is lost and RUU ends with an error window that tells me that the memory could not be read.
My ppc is not sim locked,i can use whatever sim i want with it.
please help me,i am desperate newbie. thanks.
soriyn said:
hy. i'm a newbie so plz escuze my mistakes and most of all my english.
i have a mda vario or htc wizard 200 as i know.
on the start screen,it shows
IPL 1.06
SPL 1.06
GSM 01.12.10
OS 1.6.2.1
it's a G3 wizard. My problem is that it has the T-Mobile original german ROM and i want it in english. i have read most of the forums here and tried many ideas i found here but nothing helped me so far... i tried cid unlock with lokiwiz,it shows me that is unlocked but when i try to flahh it with the .exe flasher,downloaded Rom-s for it from here,it's not working. I have Win7 now and i tried with Windows mobile device center sync software for win7 and nothing,i tried in Win xp with activesync and nothing,the same simpthomes. It syncs,detects my ppc,i start the RUU,detects the Rom i have,but when i get to the flash window,just after it tells me that the flash process will take about 10 minutes,my ppc disconnects,enters in the bootloader mode,connection is lost and RUU ends with an error window that tells me that the memory could not be read.
My ppc is not sim locked,i can use whatever sim i want with it.
please help me,i am desperate newbie. thanks.
Click to expand...
Click to collapse
turn off the device and disconnect the battery as well sim card........ leave without sim card and plug it back battery then take away your device into bootloader mode to reflash again