Related
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
which is your device,post full data of your phone,IPL/SPL...? Make...?
As you say you installed through Shelltool,is it a G4 DOC chip version ?
You say it's stuck at the splash screen with ipl/spl and gsm version,which splash screen,is it OS (Rom) initial splash screen or a Bootloaders (Multicolored) screen ?
Secondly ,try to get it into bootloaders (multicolor) screen,if it gets into bootloaders,connect it to PC via usb cable,check small usb appears at the bottom of the bootloader mode in the phone,if it does,than flash a carrier's official Rom to recover back to it's default status.
Good luck
Try the Button's ROM (which is in Wizard Upgrading subforum). Then unlock it again (It may be causd by a fake CID unlock when you try to unlock when IPL/SPL is 2.xx)
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
alldoe said:
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
Click to expand...
Click to collapse
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
luoluomeng said:
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
Click to expand...
Click to collapse
Hello! I have CID unlocked. When I install Button ROM my IPL and SPL is the same (1.01). Every RUU works but It still frozen. 2 Days ago i found on other forum this advice:
INSTRUCTION :
1. miniSD - formated in PC - FAT format (now FAT32 !)
2. Wizard On and Bootloader (press reset and keep photo button let go reset) 3 color display. Put in card to Wizard.
3. Connect USB - PCC to PC
4. Launch MTTY 1.42 (my ver.) with USB connection
5. Write command - r2sd os end press enter
6. Program it will record OS on miniSD
7. After recording make Hard Reset or turn on Bootloader
8. On Display should be written - Format partition ?? (5 sec.) - to confirm press Voice dial button. If inscription it will disappear repeat point 7.
9. If Format partition successful wait OS is write. Done.
10. Draw out miniSD
11. Make Hard Reset
12. Enter in bootloader
13. FOR NON CID WIZARD - Flashing Wizard RUU (must be proper version) - ERROR 300 is bad RUU ERROR 266 turn off Wizard and turn on connect to PC
14. With CID (for example CID G4) seek forum for flashing Wizard with CID G4
My Wizard it lives
Click to expand...
Click to collapse
I was carry out all command step by step, and after flashing proper version Orange ROM my Wizard woken up, but today my Wizard get stuck again and now this way don't work, and I have to find a new method to rescue my PDA.
My Wizard woke up! I find ERA PL ROM (RUU_Prodigy_3829_382130_027111_TMO_PL_PLK_Ship) which flash excellent and working, but now I have a new problem. I can install other ROM after that but none of them work, every stucked at Splashscreen like before.I need to find some WM6 ROM which will working? Someone have some suggestion?
alldoe said:
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
Click to expand...
Click to collapse
i have the same proplem but i have a g4 wizard and it's not cidlocked tell me plz what to do plzzzzzzzzzzzz :'(
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
ps:sorry for the double posting(wizard+wm6) but now i figured out that since my phone doesnt start and hasnt a wm6 rom on it , the place for this thread is here
fulgerul said:
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
ps:sorry for the double posting(wizard+wm6) but now i figured out that since my phone doesnt start and hasnt a wm6 rom on it , the place for this thread is here
Click to expand...
Click to collapse
Is it the Bootloaders screen(Tricolor) with IPL/SPL or initial loading screen with ipl/spl ?
What ipl/spl...? it displays at the moment ?
You can try to get into Bootloaders mode (tricolor screen) by pressing and holding down the camera button and press the Soft Reset button at the same time with the stylus or turn off the phone and while pressing and keeping holding down the camera button,Power On the phone,it'll wake up and go into Bootloaders (tricolor screen).if it goes into bootloaders,connect your phone to the pc via usb and check if small usb appears at the bottom of the bootloaders screen,if its there run the Ruu to flash,But first post your present ipl/spl..? here.
Cheers
hmm , this is from XDADeveloperWiki
Once the flash is done and your Wizard is rebooted, it will display an IPL of 1.xx and an SPL of 2.xx.
Click to expand...
Click to collapse
well, in my case , after button rom flashes wizard displays IPL 1.01 SPL 1.03 and after i flash the xda_mini_launch_rom it displays IPL 1.03 SPL 1.05 . NOT SPL 2.xx as mentioned in the tutorial . why ?
zabardast_1 - many thanks for the quick reply mate. it starts with the ipl spl screen. i wrote the values above.
i get it into bootloader with the camera + on button , bot the active sync on the systray , doesnt activate, it remains grey (like no device is connected). weird stuff.
yesterday i just upgraded a g4 wizard to wm6 and everything went smooth , an now
fulgerul said:
hmm , this is from XDADeveloperWiki
well, in my case , after button rom flashes wizard displays IPL 1.01 SPL 1.03 and after i flash the xda_mini_launch_rom it displays IPL 1.03 SPL 1.05 . NOT SPL 2.xx as mentioned in the tutorial . why ?
Click to expand...
Click to collapse
ok,after flashing button's rom or xda_mini you'll certainly have an ipl/spl 1.xx,cuz these roms have actually ipl/spl 1.xx,they are aku 1.xx roms,it's required to have ipl/spl 1.xx to use lokiwiz02b tool to SIM/CID unlock the phone,only then it can be upgraded to any wm6 roms.But to upgrade to wm6 its essential to have ipl/spl 2.xx,so to get to ipl/spl 2.xx,you have to flash your phone with T-mobile 2.26,then it'll show an ipl/spl 2.xx as required,ok
Cheers
thanks mate , but in order to do the lokiwiz soft spl i need to have a working phone (i need to write the cab into my phone and execute). by doing so , my phone needs to work after flashing the button rom or the xda mini launch rom (right?). but mine , after flashing, remains in the ipl/spl screen (not the bootloader).
if i flash an o2 xda mini original rom , do i have a chance to revive the phone and to start it in order to apply the lokiwiz soft spl ?
Activesync will not work in bootloaders mode,bootloaders cut off the activesync,you can only verify the connectivity between your phone and pc,if in bootloaders,connect the phone to the pc via usb cable and check if small usb appears at the bottom of the bootloaders,if its there then just flash the rom,there's no need to establish connection through activesync,ok
fulgerul said:
thanks mate , but in order to do the lokiwiz soft spl i need to have a working phone (i need to write the cab into my phone and execute). by doing so , my phone needs to work after flashing the button rom or the xda mini launch rom (right?). but mine , after flashing, remains in the ipl/spl screen (not the bootloader).
if i flash an o2 xda mini original rom , do i have a chance to revive the phone and to start it in order to apply the lokiwiz soft spl ?
Click to expand...
Click to collapse
YES ! first of all you got to have a working OS on the phone to activesync,only the you can perform with lokiwiz02b,ok
ok , so what should i do in order to start it succesfully and use lokiwiz. i cant find an original o2 rom and button rom or launch rom doesnt start my phone. what can i do ?
the o2 roms were deleted from xda dev ftp
ps : mate , if u r kind , log in to yahoo or msn , i m trying to contact u . ty
after a lot of searching and digging, i found the missing xda dev ftp O2 original roms . i flashed Xda_MiniS_LaunchROM_v154102 , everything went ok , same result. doesnt pass the ipl spl screen. tried RUU_Wizard_1050402_101_11210_O2_ENG and same thing. im getting really confused. my pc responses when i connect the wizard, it flashes with no errors , but it wont start. what can i try more ?
ohh, i have made a new nasty descovery: when i keep pressed down the comm button and the voice button and press the reset with stylus, the phone turns off and restarts in spl/ipl screen instead of hard resseting. is it really messed up ?
I'm afraid m8,it has most probably some hardware issues,better get it checked by some techy or mobile repair shop.
Cheers !
thanks mate. you are most probably right. do you have any idea what should be checked and how ? i ask this because the software part is clearly damaged.
can i revive it using mtty program ? as a last resort. some mtty commands ? ty
help me to break & solve this problem, maybe can also help the other members..
I tried to upgrade my XDA to WM2003SE everything goes right,
bootloader first time i still use v5.22
but when I soft reboot it freezes on the OZUP screen and
message ONLY FOR MICROSOFT bla bla bla....
i get this ROM from http://www.romkitchen.de/ ==> WM2003SE
then downgrade bootloader from v5.22 to v5.15,
using MMC (flash SD) continue to special rom 1.2,
and then cooked again using PC2002 by my own creation based from
romkitchen, what i want to ask is :
i cannot connect again via dekstop activesyn if i want to change
my ROM because my cradle cannot detect my charger?? but if i charge
directly, its work. What is the problem?
is my cradle/dekstop broken at the charger socket?
so what i need to do? just change the wire or socket or
i use the step like at http://wiki.xda-developers.com/index.php?pagename=WallabyCradleMod
if i prefer use the 2nd method, is that really OK? so just used cradle/deskstop, no need
power charger again if i want to change ROM to WM2003SE, because only can use via activesync?
after i change bootloader to v5.15, keep trying to change but only can via Flash SD Card,
i change to WM 2003 final, still same problem....after finish, only screen cannot enter the
menu or else, only boot screen until i am waiting for 15 minutes??? then change again to
WM2003 but using from http://www.romkitchen.de/tools, still same again....boot screen again...
haiyaaaa.....what happen?? i dont know, tired, always overtime to do this,hehehhee...
all my friends, help me...need your advice ^_^V
*now, i still used ROM from PC 2002,cooked again using PC2002 by my own creation based from romkitchen.
bootloader v5.15
Microsoft Pocket PC --> PC2002
Version 3.0.12039 (Build 11178)
ROM version : 3.17.03 ENG
ROM date : 05/15/03
Radio version : 6.24.00
Protocol version : 324e4
Model No.: PW10A1
I can not really help you, but i was also in the same situation, that i have had a device, that doesn´t work with any other ROM than PPC2002
Flashed several WM2003 ans the WM2003SE but non of them worked.
So i rest at PPC2002
Stefan
ow ow...
auch.. ok, thanks for the comment, i give-up,hehehe..but only for now,
take a rest first but i dont know for t'mrow, actually from 10 flashed,
i got 1 success, can got WM2003SE but with almost empty battery,
i know the inside and already set all, including i notice bluetooth icon,hehehe..
but how? i wonder that my sx56 with fake bluetooth, only icon
but after i charge my sx56 then i soft reset, its gone, back again with only boot-screen, after that, i can't find again WM2003SE ROM only lock with boot-screen, and ONLY FOR MICROSOFT..blablabla...
and about for my cradle/dekstop? how is it? can u give me solution to fixed it??
btw,thanks for helping, tips & trick hehehe...
i will keep trying to find/solved this problem by my own way ^_^V
modify my cradle/dekstop success
its working, i try to modify my cradle/dekstop with that steps (look at the top this thread), and it's work...actually not me who did it, but my friend,hehehehe....i ask his help and he agrre to doit, but all the risk is still at me, now i can charge and also syncronized to my notebook
Hey people,
I have got on nice MDA with ipl and spl 2.21.0001
me problem is i have no idea wath did happend to it.
the MDA starts up shows T-Mobile ... an go to the Bootloaderscreen (red IPL2.21.0001, green spl 2.2.0001, blue, with)
so i have tried to flash it now with WM5 from T-Mobil image ver 2.26.10.105 (from this nice Board here
The flash tool shows no image information of my MDA but the posibility i there to push the update button. If i do that the update tool trys to flash a few seconds and stops with error code 294 (invalid vender id). on the MDA is noch change (still bootloaderscreen)
some one of you has an idea wath could be happend to this device ?
or an idea wath can i doo ?
Yes!!!
Your problem... is NOT READ Enough!
So please read how to make a hardSPL cause your wizard is G4....
if you do it well you can upgrade whatever you want but for this time... you need to exit bootloader screen so... perform sofresets! or hardreset!
Keep reading for more chances...
You don't need to apply HardSPL or SoftSPL to flash an official stock rom.
Which language or version was working primarily on the phone before you flashed t-mobile 2.26 ?
Secondly download 'RUU_NoId' or 'RUU_MUN' and replace it with the RUU in the rom and Run the replaced RUU,hope it'll work.
Hi,
and thanks for the answers.
i do not know wath was befor on it. i have get it with the information that there was an klabel inside for the keybord not in the slot .... and after "reparing" - the mda do not boot.
up to now i have update it with orginal firmware and it runs again ... so peraps someone has talk **** to me ?! - now i think it was a bad flash
p.s. the vendor id problem was my mistake, was the wrong update
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
brick...
chipis said:
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
Click to expand...
Click to collapse
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Thank for answer me and understand what i ment
Ok what software you recoment?. I do not know if i have a unlocked phone but i do know that i used it with t-moble even that my pocket pc is for cingular, i went to those stores that unlocked phones and that it
Help.
I have a Wizard G4 and I tried to install a WM6.5 ROM (TechTeamup Mega Wizard rom) from the default WM5. I did not put in the hard-spl (as I now read) before I tried to flash. Now when it boots, I go strait to the flash screen (tri-color) screen. I tried ot run the hard-spl-G4 and it says it cannot find a device. I have tried to re-flash back to WM5 ROMs that I have found, however it says it cannont complete "ERROR 296: UPGRADE ONLY, which makes me belive I need a G4 Wizard ROM that is a full (not upgrade). What steps should I take now to revert back to a WM5 so I can re-try the "unlock" hard-spl proceedure to make the phone WM6 compatible?
Anyone have any suggestions?
IPL 2.28.0001
SPL 2.28.0001
Download the original ship ROM for your phone.
Turn the phone off.
Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen.
Now run the ROM update to flash back to WM5.
ricozy said:
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Click to expand...
Click to collapse
I brick my wizard too... What happened was I flashed my own cook of m6r5 it say successful but on reboot, it shows htc logo then stays ay tricolor screen:
IPL 2.26
SPL 2.26
Bootloader wont work..tried many times but I cannot connect to PC...
Tried ricozy post above, can access 3 color... but still cannot connect to PC...
Please help...anyone..
IF u can enter bootloader...connect to pc...u shud c "USB" written in the left bottom corner ...then flash a rom as usual