hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
ps:sorry for the double posting(wizard+wm6) but now i figured out that since my phone doesnt start and hasnt a wm6 rom on it , the place for this thread is here
fulgerul said:
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
ps:sorry for the double posting(wizard+wm6) but now i figured out that since my phone doesnt start and hasnt a wm6 rom on it , the place for this thread is here
Click to expand...
Click to collapse
Is it the Bootloaders screen(Tricolor) with IPL/SPL or initial loading screen with ipl/spl ?
What ipl/spl...? it displays at the moment ?
You can try to get into Bootloaders mode (tricolor screen) by pressing and holding down the camera button and press the Soft Reset button at the same time with the stylus or turn off the phone and while pressing and keeping holding down the camera button,Power On the phone,it'll wake up and go into Bootloaders (tricolor screen).if it goes into bootloaders,connect your phone to the pc via usb and check if small usb appears at the bottom of the bootloaders screen,if its there run the Ruu to flash,But first post your present ipl/spl..? here.
Cheers
hmm , this is from XDADeveloperWiki
Once the flash is done and your Wizard is rebooted, it will display an IPL of 1.xx and an SPL of 2.xx.
Click to expand...
Click to collapse
well, in my case , after button rom flashes wizard displays IPL 1.01 SPL 1.03 and after i flash the xda_mini_launch_rom it displays IPL 1.03 SPL 1.05 . NOT SPL 2.xx as mentioned in the tutorial . why ?
zabardast_1 - many thanks for the quick reply mate. it starts with the ipl spl screen. i wrote the values above.
i get it into bootloader with the camera + on button , bot the active sync on the systray , doesnt activate, it remains grey (like no device is connected). weird stuff.
yesterday i just upgraded a g4 wizard to wm6 and everything went smooth , an now
fulgerul said:
hmm , this is from XDADeveloperWiki
well, in my case , after button rom flashes wizard displays IPL 1.01 SPL 1.03 and after i flash the xda_mini_launch_rom it displays IPL 1.03 SPL 1.05 . NOT SPL 2.xx as mentioned in the tutorial . why ?
Click to expand...
Click to collapse
ok,after flashing button's rom or xda_mini you'll certainly have an ipl/spl 1.xx,cuz these roms have actually ipl/spl 1.xx,they are aku 1.xx roms,it's required to have ipl/spl 1.xx to use lokiwiz02b tool to SIM/CID unlock the phone,only then it can be upgraded to any wm6 roms.But to upgrade to wm6 its essential to have ipl/spl 2.xx,so to get to ipl/spl 2.xx,you have to flash your phone with T-mobile 2.26,then it'll show an ipl/spl 2.xx as required,ok
Cheers
thanks mate , but in order to do the lokiwiz soft spl i need to have a working phone (i need to write the cab into my phone and execute). by doing so , my phone needs to work after flashing the button rom or the xda mini launch rom (right?). but mine , after flashing, remains in the ipl/spl screen (not the bootloader).
if i flash an o2 xda mini original rom , do i have a chance to revive the phone and to start it in order to apply the lokiwiz soft spl ?
Activesync will not work in bootloaders mode,bootloaders cut off the activesync,you can only verify the connectivity between your phone and pc,if in bootloaders,connect the phone to the pc via usb cable and check if small usb appears at the bottom of the bootloaders,if its there then just flash the rom,there's no need to establish connection through activesync,ok
fulgerul said:
thanks mate , but in order to do the lokiwiz soft spl i need to have a working phone (i need to write the cab into my phone and execute). by doing so , my phone needs to work after flashing the button rom or the xda mini launch rom (right?). but mine , after flashing, remains in the ipl/spl screen (not the bootloader).
if i flash an o2 xda mini original rom , do i have a chance to revive the phone and to start it in order to apply the lokiwiz soft spl ?
Click to expand...
Click to collapse
YES ! first of all you got to have a working OS on the phone to activesync,only the you can perform with lokiwiz02b,ok
ok , so what should i do in order to start it succesfully and use lokiwiz. i cant find an original o2 rom and button rom or launch rom doesnt start my phone. what can i do ?
the o2 roms were deleted from xda dev ftp
ps : mate , if u r kind , log in to yahoo or msn , i m trying to contact u . ty
after a lot of searching and digging, i found the missing xda dev ftp O2 original roms . i flashed Xda_MiniS_LaunchROM_v154102 , everything went ok , same result. doesnt pass the ipl spl screen. tried RUU_Wizard_1050402_101_11210_O2_ENG and same thing. im getting really confused. my pc responses when i connect the wizard, it flashes with no errors , but it wont start. what can i try more ?
ohh, i have made a new nasty descovery: when i keep pressed down the comm button and the voice button and press the reset with stylus, the phone turns off and restarts in spl/ipl screen instead of hard resseting. is it really messed up ?
I'm afraid m8,it has most probably some hardware issues,better get it checked by some techy or mobile repair shop.
Cheers !
thanks mate. you are most probably right. do you have any idea what should be checked and how ? i ask this because the software part is clearly damaged.
can i revive it using mtty program ? as a last resort. some mtty commands ? ty
Related
ive got a htp 3300 from movistar spain and i allready got it unlocked, yesterday i put the wm6 english on it and today y tried to put
PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap, now
i can see only the white htc screen
IPL 3.007.001
SPL 3.07.0000
GSM 02.69.90
OS 1.28.0.0
the phone dont start anymore
y need helpe please
Can you get in to the bootloader?
If you do then you can put an original rom back. If you don't then send it to the service.
An unlocked device is out of warranty so be prepared to pay for the service.
Go to wiki of Artemis there you can find the method to get in to the bootloader.
Goof luck! << you need that.
you meen push the record button and reset in the same time???
i tried this befor but never go in bootloader modus maybe i make something wrong pleas help me
As of this http://forum.xda-developers.com/showthread.php?t=308242#1 threath of meschle states your device is a brik.
I'm sorry to tell you that.
meschle said:
Do Not flash your Artemis with a different carrier/cooked Rom without cid unlocking
--------------------------------------------------------------------------------
Noobs beware!
As a number have been flashing their devices with various roms not from their own carrier or country or cooked roms and bricking their device - I put up this sticky. Your device must be cid unlocked first before you do this. This applies to the coming wm6 roms to - if the rom is not specific to your device - i.e. if you try to flash the upcoming htc 3300 wm6 rom on O2 orbit - you must cid unlock first - with imei check or you will end up with a BRICK!
This does not apply if you are only updating the os http://forum.xda-developers.com/showthread.php?t=299154 or radio.
cid = country id i.e. locked to that country/language/vendor
cid unlock for the artemis is here with USPL http://forum.xda-developers.com/showthread.php?t=311403 (thanks pof)
or here http://www.imei-check.com/c3unlock.php (costs though)
Bricked devices
If you have flashed your device and not cid unlocked it, your device maybe salvagable if you can get it into bootloader mode.
Hold down the voice speed dial button and soft reset - you should then enter bootloader mode 'multicolored' screen'
If you do, attach device to pc via usb cable (a small usb will appear bottom left of screen) and flash factory rom. (run rom executable or RUU updater from pc) You do not need to be activesynced to do this.
HTC P3300 WWE factory rom downloadable here http://rapidshare.com/files/19322112...0_WWE_SHIP.rar
Dopod P800 WWE factory rom downloadable here http://rapidshare.com/files/21058219...0_WWE_SHIP.rar
O2 Orbit WM5 WWE factory rom downloadable here http://rapidshare.com/files/41574866/Arteimg.nbh
O2 Orbit WM6 WWE factory rom downloadable here http://rapidshare.com/files/46377862....90_Shi p.exe
Before you flash again with a non-factory rom, your device MUST be cid unlocked.
If you cannot enter bootloader mode your bootloader has been damaged and your device will need to be sent away for repair.
Click to expand...
Click to collapse
movilstore said:
ive got a htp 3300 from movistar spain and i allready got it unlocked, yesterday i put the wm6 english on it and today y tried to put
PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap, now
i can see only the white htc screen
IPL 3.007.001
SPL 3.07.0000
GSM 02.69.90
OS 1.28.0.0
the phone dont start anymore
y need helpe please
Click to expand...
Click to collapse
i had the same problem and took me 3 days to fix it. so maybe this will work for you too !
first take out the battery for 30 min then push the reset button and put the battery back and turn on the device. if this not working. try to start bootloader by pressing and holding the record button and on/off button and push the reset butoon in the same time but keep pressing the record button and on/off button till a colored screen shows up??? sometimes it doesn't appear at the first time so just keep trying .
if you have bootloader you can reflash a rom. but you need to format your memorystick first to fat on your pc then put the image rom (nbh file) and rename it to Arteimg.nbh !! i used OrbitO2UK image.
hi all ..
I did flash my HTC wizard with new rom after finishing the install the device reboot and stacked on the boot screen then I tried to go to the boot screen but I couldn't , I tried to make hard rest but also I coudn't nothing is working even charing the device cant be made .
bye bye
Are you able to get to a multi-colored screen with numbers?
In case you don't know, to get to the bootloader screen hold down the camera button and press the power button.
now i got the same problem.
I updated the rom & now i have the multi-colored (red/green/blue/white) screen
with RUU - IPL 2.18 - SPL 2.18 - USB on it (Qtek 9100)
I downloaded the tools from Vippie in the thread "How to flash a new ROM to your Wizard... a little tutorial!" but those won't help...
anybody got any advice? I would like to install WM6...
thanks in advance!
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
which is your device,post full data of your phone,IPL/SPL...? Make...?
As you say you installed through Shelltool,is it a G4 DOC chip version ?
You say it's stuck at the splash screen with ipl/spl and gsm version,which splash screen,is it OS (Rom) initial splash screen or a Bootloaders (Multicolored) screen ?
Secondly ,try to get it into bootloaders (multicolor) screen,if it gets into bootloaders,connect it to PC via usb cable,check small usb appears at the bottom of the bootloader mode in the phone,if it does,than flash a carrier's official Rom to recover back to it's default status.
Good luck
Try the Button's ROM (which is in Wizard Upgrading subforum). Then unlock it again (It may be causd by a fake CID unlock when you try to unlock when IPL/SPL is 2.xx)
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
alldoe said:
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
Click to expand...
Click to collapse
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
luoluomeng said:
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
Click to expand...
Click to collapse
Hello! I have CID unlocked. When I install Button ROM my IPL and SPL is the same (1.01). Every RUU works but It still frozen. 2 Days ago i found on other forum this advice:
INSTRUCTION :
1. miniSD - formated in PC - FAT format (now FAT32 !)
2. Wizard On and Bootloader (press reset and keep photo button let go reset) 3 color display. Put in card to Wizard.
3. Connect USB - PCC to PC
4. Launch MTTY 1.42 (my ver.) with USB connection
5. Write command - r2sd os end press enter
6. Program it will record OS on miniSD
7. After recording make Hard Reset or turn on Bootloader
8. On Display should be written - Format partition ?? (5 sec.) - to confirm press Voice dial button. If inscription it will disappear repeat point 7.
9. If Format partition successful wait OS is write. Done.
10. Draw out miniSD
11. Make Hard Reset
12. Enter in bootloader
13. FOR NON CID WIZARD - Flashing Wizard RUU (must be proper version) - ERROR 300 is bad RUU ERROR 266 turn off Wizard and turn on connect to PC
14. With CID (for example CID G4) seek forum for flashing Wizard with CID G4
My Wizard it lives
Click to expand...
Click to collapse
I was carry out all command step by step, and after flashing proper version Orange ROM my Wizard woken up, but today my Wizard get stuck again and now this way don't work, and I have to find a new method to rescue my PDA.
My Wizard woke up! I find ERA PL ROM (RUU_Prodigy_3829_382130_027111_TMO_PL_PLK_Ship) which flash excellent and working, but now I have a new problem. I can install other ROM after that but none of them work, every stucked at Splashscreen like before.I need to find some WM6 ROM which will working? Someone have some suggestion?
alldoe said:
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
Click to expand...
Click to collapse
i have the same proplem but i have a g4 wizard and it's not cidlocked tell me plz what to do plzzzzzzzzzzzz :'(
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
brick...
chipis said:
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
Click to expand...
Click to collapse
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Thank for answer me and understand what i ment
Ok what software you recoment?. I do not know if i have a unlocked phone but i do know that i used it with t-moble even that my pocket pc is for cingular, i went to those stores that unlocked phones and that it
Help.
I have a Wizard G4 and I tried to install a WM6.5 ROM (TechTeamup Mega Wizard rom) from the default WM5. I did not put in the hard-spl (as I now read) before I tried to flash. Now when it boots, I go strait to the flash screen (tri-color) screen. I tried ot run the hard-spl-G4 and it says it cannot find a device. I have tried to re-flash back to WM5 ROMs that I have found, however it says it cannont complete "ERROR 296: UPGRADE ONLY, which makes me belive I need a G4 Wizard ROM that is a full (not upgrade). What steps should I take now to revert back to a WM5 so I can re-try the "unlock" hard-spl proceedure to make the phone WM6 compatible?
Anyone have any suggestions?
IPL 2.28.0001
SPL 2.28.0001
Download the original ship ROM for your phone.
Turn the phone off.
Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen.
Now run the ROM update to flash back to WM5.
ricozy said:
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Click to expand...
Click to collapse
I brick my wizard too... What happened was I flashed my own cook of m6r5 it say successful but on reboot, it shows htc logo then stays ay tricolor screen:
IPL 2.26
SPL 2.26
Bootloader wont work..tried many times but I cannot connect to PC...
Tried ricozy post above, can access 3 color... but still cannot connect to PC...
Please help...anyone..
IF u can enter bootloader...connect to pc...u shud c "USB" written in the left bottom corner ...then flash a rom as usual
Dears Freinds
I have Qtek s200 and i Upgrade it from win 5 to win6.5 and when it restart hang up and dosent work any more
so pls can anyone help me
Muamer
By Hung up do you mean it goes into the bootloader screen (tri-colour)
First things first
Did you perform a HardSPl if not you need to do this first. Do a search for it, but make sure you get the correct one. By this I mean a G3 or G4, when you go into the bootloader screen look at the SPL if it ends in .000 it is a G3 if it ends in .0001 it's a G4.
This is just the same as flashing a Rom.
Then check this page and download the Qtek NVID Rom flash that and it should get your beloved prophet back to WM5
http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs
BUT before you do any flashing open up your activesync click on FILE then CONNECTION SETTINGS uncheck ALLOW USB CONNECTIONS then OK.
Then connect your phone via the USB in bootloader mode (press and hold the communication button and press the reset button keep holding the communication button until you get the tri colour screen) look at the bottom left of the screen for USB (in the white part) as long as you have got this you can begin flashing.
Dear Dixiesmu
when I turn in on i jus t get the first page
IPL 2.10
Spl 2.20.0000
gsm 02.47.21
os 10.1.0.811
And i wnat to tel u that befor the os is windows 5 with sweden lang.
so the link u gave me dosent include sweden so can i use the english rom
and im new in this feld so can help me more if u can and i will appreciate that
Many thanx for you reply
My freind
I did what u suggest and it works and now my qtek is working agian and can i upgrade it to win6.5 and if u have tje link for my qtek pls send it me
Thanx again for your help
Muamer
WM6.0/6.1/6.5 Roms
I have found that Bikertibi roms seem to be the best (only my opinion and no disrespect to the other fantasic chefs, long may thier excellent work continue ).
They also include the HardSPL for both G3 and G4 devices.
Another good one is Gullum's Prophet TouchXB if I recall this also includes the HardSPL, but please check as I am not 100% certain.
G4
Hi Malfakhry
Forgor to mention that your device is a G4
Dear
How did you know that my device is G4
thanx
G3 or G4
If your SPl ends in .000 then it's a G3
If it ends in .0000 or .0001 thens it's a G4
dear
You are very helpfull thanx for you
Dear
I read in wiki that if its end in .000 is g3 and .0001 is g4
http://wiki.xda-developers.com/index.php?pagename=prophet_g3g4_how
so mine ends with
Spl 2.20.0000
so it must be g3 that right or not
thanx again
I also facing d similar problem like bro malfakhry. After flashing back to Qtek NVID Rom WM5 it go hang....and it show
IPL 2.20
SPL 2.20.0000
GSM 02.47.21
OS 2.20.7.34
May I know my device is G3 or G4?
How myself gonna to solve this hang issue?
Thanks in advance.
rgrds
lrew9999
G3 or G4
Hi All
If your device was a G3 the SPL can only end in .000
As your devices end in .0000 it is a G4
When you flashed the NVID rom this means there is no vender identification and will reset your SPL back to 0 all you do is count the noughts as it can only be 3 or 4 this then gives you the G rating.
If your phone hangs after this flash then try a hard reset first if it still hangs just go through the whole proccess again from the start remembering the hardSPL and when done perform a hard reset.
Dixiesmu said:
Hi All
If your device was a G3 the SPL can only end in .000
As your devices end in .0000 it is a G4
When you flashed the NVID rom this means there is no vender identification and will reset your SPL back to 0 all you do is count the noughts as it can only be 3 or 4 this then gives you the G rating.
If your phone hangs after this flash then try a hard reset first if it still hangs just go through the whole proccess again from the start remembering the hardSPL and when done perform a hard reset.
Click to expand...
Click to collapse
Dear Dixiesmu,
Its work now!!!
Thanks a million.