Related
Hi every one.
So i set "button lock" and also disable mainly all notifications but every time a new sms arrives,the screen goes on.I will like to keep the screen off because if you carry your magician in your pocket and after that sms arrives,you can accidentaly press any button or even touch the screen.
I been checking every thing i could check but i can´t find the answer about this problem.
Thanks in advance.
Third party software Pocket Zen Phone or phoneAlarm.
Ok i´ll check it and see what i can do.
Cheers mate.
User22 said:
I will like to keep the screen off because if you carry your magician in your pocket and after that sms arrives,you can accidentaly press any button or even touch the screen.
Click to expand...
Click to collapse
There are many occasions the Magician turns on its screen. Rather than trying to find and disable all these, I copied TPDisable.exe and TPEnable.exe from the original Extended ROM into my Program Files folder, and then assigned them to a hardware key (using Hotbutton, so that I can use the same key for both).
As the name implies, TPDisable disables the touchscreen (not the display!), and TPEnable re-enables it. So, before I put my Magician into my pocket, I now disable the touchscreen (one press of a button). That still leaves the keys active, true, but I found that normally the touchscreen is much more likely to be the culprit when strange things happen on your Magician while it's in the pocket, and turned itself on.
Cheers
Daniel
@ tadzio
Well,that is a very interesting solution,but i can´t find TPDisable.exe
or TPEnable.exe inside my magician.I need a bit more info from you
Daniel.
Thanks a lot for your replies.
What happens if you hold down power button for 2 seconds to switch off backlight? Does the light still illuminate on receipt of sms?
@ cruisin-thru
I can´t see the point of your question,mainly because the thing i am looking for is to "switch off" my Qtek like a normal mobile phone,i mince buttons locks and screen off when a new sms or incoming call arrives and when you push power button for example,then screen go on and also release the lock of the buttons.
Any one can say that then i can use deltalock.I did it but the battery live is going down very quick.
Screenlock is not working properly also,i will say that Deltalock is 95% a lot better than Screenlock.
And finally,why microsoft is developing this OS without fully screen off selectable option???. Who knows!!!
Cheers
User22 said:
Well,that is a very interesting solution,but i can´t find TPDisable.exe or TPEnable.exe inside my magician.I need a bit more info from you Daniel.
Click to expand...
Click to collapse
Both programs are in the Extended ROM. Most users have made this visible (though not writable) by performing a Hard Reset, and immediately after completing the initial screen adjustment and mini-tutorial and before the device starts installing programs, a Soft Reset.
If you do not want to do a Hard Reset, search this site's FTP server for Magician Extended ROM downloads. There were a few there last time I looked.
Cheers
Daniel
Well,after config hotbutton to TPDisable and TPEnable i can´t enable the screen and hardware buttons.
TPDisable is disablind the screen but also all the hardware buttons ( with and without button lock at settins),even the power button.
I use same hardware button for TPDisable and TPEnable ,is that correct or i am doing silly things?
If I arrive an sms the screen is switching on and after a few seconds switching off again if I don't press any key or tap the screen!
It's a changeable registry key:
HKEY_LOCAL_MACHINE / System / CurrentControlSet / Control / Power /
WakeupPowerOff =12 (the default is 180)
DisableGwesPowerOff=0 (the default is 1)
If you switch on the Jam (power button) need to press some other key too, because it switches off after 12 seconds!!!
by Avers
@avers
Well that is another solution but i insist that there should be an easiest way to keep the screen fully off when a new sms or what ever arrives,including hardware buttons off ofcourse.
Any suggestion more?, perhaps at the end and betwen all of us ,we can find the solution.
Cheers.
I think the best solution is third party software like PHONEALARM,
it's easiest way to get main tweaks of Pocket Windows.
get it there
http://www.pocketmax.net/phoneAlarm.htm
Well my friends,pocketzenphone is not doing what i am looking for.
Next step is to try phonealarm,but probably will work the same way as pocketzenphone,leting the screen to go on every time a new sms arrives.
Sorry for my languaje but F... microsoft and F... devil gates.
As you can read on this post ,phonealarm IS NOT doing it.
http://www.pocketmax.net/phpbb2/viewtopic.php?t=429
phonealarm has option named "Don't activate backlight on alarm"
ALARM there means any event, that needs notification.
now i am understanding, that it is some differ that you need.
also i advice you make some registry tweaks to make a very short backlite time when sms arrives.:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Power\WakeupPowerOff = 10
this timeout in seconds. is used when our device self power on, when SMS arrives or we push the POWER button and do nothing anymore
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Power\DisableGwesPowerOff = 0
this key is enables this power control system (necessarily change it, or first key will not work)
after the editing registry you need to reboot PDA.
sorry for poor english, i translate text from russian.
if you want to use online translator i can give you original URL
_http://forum.ladoshki.com/viewtopic.php?t=16012
Thank you for your reply i will try like you and others point out and also will keep looking for that utopic soft.
deltaLock locks the screen and buttons even if you get sms or calls. I use it on my JAM and it works so far.
bnycastro said:
deltaLock locks the screen and buttons even if you get sms or calls. I use it on my JAM and it works so far.
Click to expand...
Click to collapse
If you read one of my post ,you will see that i allready said that Deltalock is working but it is KILLING the battery live very fast and when i say VERY FAST it mince that you will get almost 6hours against the normal live (more than 15hours).
Cheers mate.
I think if you keep your ppc on all the time you will get this battery life. Anyway I think deltaLock is for keeping your PPC on and having screen and button lock, not having it in suspend mode and not allowing the screen to power up. Sorry about that, seem to have misunderstood your post.
Don´t worry mate, at the end we are all together trying to find a solution to this microsoft silly programing, any comment and any new idea is wellcome.
Cheers.
Hi
I want to phone to keypad lock itself automatically as a normal mobile do. There must be a setting for this? As for now I have the lock thing in my today screen and have to press it. I often miss and hit something else and the phone calls people all afternoon while in my pocket. Somewhat anoying.
/d
Would be nice to have a device lock that didnt take up so much space on the today screen.
knowsleyroader said:
Would be nice to have a device lock that didnt take up so much space on the today screen.
Click to expand...
Click to collapse
Then look for the DeviceLock CAB file and assign it to a hardware button so you can remove it from the Today Screen (just like I did last week ).
Did a search for that cab file, but didnt find it. Where is it supposed to be?
/d
i used vjkeypress with the link -133 which will lock the device and assined it to my comm butten because i don´t use it that often and have it in my tray also
I cant seem to install the devicelock.cab on my Blue Angel ... is it because it wont run on WM2003 or some other reason maybe.
Does anybody know about another program for key locking the BA?
Cheers
xdjneo said:
I cant seem to install the devicelock.cab on my Blue Angel ... is it because it wont run on WM2003 or some other reason maybe.
Does anybody know about another program for key locking the BA?
Cheers
Click to expand...
Click to collapse
You might want to ask that in one of the BA forums, this is a Wizard Forum...
Frezzor: How do you assing the shortcut to the comm button? I can only choose installed program when assigning the buttons.
/d
Hi all
Can anyone send me the following registry key (and subkeys) please (of the HTC TyTN / Hermes)
HKLM\SOFTWARE\Microsoft\Shell\Keys
I have a problem with my power button and I've discovered that some values are missing in this registry key.
P.S.: If possible, please send me the configuration from an original rom without any third party software.
Many thanks!
nero said:
Hi all
Can anyone send me the following registry key (and subkeys) please (of the HTC TyTN / Hermes)
HKLM\SOFTWARE\Microsoft\Shell\Keys
I have a problem with my power button and I've discovered that some values are missing in this registry key.
P.S.: If possible, please send me the configuration from an original rom without any third party software.
Many thanks!
Click to expand...
Click to collapse
Hopefully Keys attached
Mike
many thanks Mike
but "Button 6" configuration is missing... is that alright?
by default there is no configuration for this button?
nero said:
many thanks Mike
but "Button 6" configuration is missing... is that alright?
by default there is no configuration for this button?
Click to expand...
Click to collapse
Yes, until now I had not noticed that but that is indeed true on mine. I have also not carried out any customisation or even reset any of these buttons (well since last HR anyway)
Mike
Hi again Mike!
Ok, I've deleted the "HKLM\SOFTWARE\Microsoft\Shell\Keys\40C5" key and now the power button works perfectly.
I have wisbar advance 2 installed and probably, somehow I think, messing arround in his settings has created the power button mapping and that makes his behaviour anoying...
Maybe this is a solution for some other people with this problem. I've seen there are more people in the forum with the "power button problem".
Many thanks.
Power Button
Good news.
Had not seen others with the problem of the "power button" but if I spot them I'll link to here and by repeating power button problem hopefully searches will lead here!!!!
Mike
checkout this one here
people saying that need to do a soft-reset...
is what I have been doing when the power button get stucked and it is not anymore
nero said:
checkout this one here
people saying that need to do a soft-reset...
is what I have been doing when the power button get stucked and it is not anymore
Click to expand...
Click to collapse
Well now, I wonder!
Perhaps you could write up a detailed piece on exactly what was happening and then the exact detail of what you did/changed. I have a pretty good picture but if you get the time the old blow by blow account would be useful.
Cheers
Mike
going to bed now-enough problems for one day!!!
Mike,
sorry but I dont know exactly what you want to say with "old blow by blow account". My native language is not english and I dont know that expression.
I can say that my power/toggle screen button becomes "non responsive" in the past couple of days, sometimes works after 3/4 presses or after a long press but other times I need to do a sw reset pressing with the stylus in the reset button/hole.
What I did to fix this malfunction is what I've described in this thread's 5 post (here)
I've used resco's Registry Editor and deleted the key "HKLM\SOFTWARE\Microsoft\Shell\Keys\40C5" and all of it's contents.
Now the power/toggle screen button works perfectly!
If you need some more information, just do has one of our tv commercial
"explains it as if I am too much donkey"
Cheers,
Nero
I'm from Portugal.. same GMT, sweet dreams
Would this make it in a wizard too?
Hi guys, I have a wizard with the power button inoperant, everything else looks work fine... I tried several tricks given in the forums and those are great to power it off but not for turning on the phone niether the display on. Would this make it in the wizard too?
Luiggi, take a backup of your registry (Everyone should before registry editing), and just try it!
V
Hi Guys,
does anyone know how to reconfigure the video-call button (the little button above the green button). I don't use this one, en would like to give it another function)
Thx!
Thanks VJ
vijay555 said:
Luiggi, take a backup of your registry (Everyone should before registry editing), and just try it!
V
Click to expand...
Click to collapse
Thank you Vijay I took a look to the 8125 registry and is quite different, i´m afraid this wouldn´t work for the Wizard. I´ve tried also a couple of your programas (VJKeypress and VJEscahaton) but can´t help either, my problem is to turn the phone on (i´ve been using softreset during a connection to the power supply) and all indicates that this is a hardware issue... any thoughts?
Take a full backup (eg SPB Backup) then hardreset. Test if a clean rom still has the problem. If it does, it's a hardware issue, get it repaired.
Otherwise, if it's software, list what you've got or rebuild your installation.
V
It died like a hero....
vijay555 said:
Take a full backup (eg SPB Backup) then hardreset. Test if a clean rom still has the problem. If it does, it's a hardware issue, get it repaired.
Otherwise, if it's software, list what you've got or rebuild your installation.
V
Click to expand...
Click to collapse
I follow your advice and @ 80% of flashing stalls for awhile with the progress bar in red, after some minutes proceeded turning the progress bar in blue color and @ 95% progress I got ERROR326 : INVALID COMMAND "With the legend "This NBF file can not be used for your phone. Please check your NBF file" The screen was white with the 95% progress bar and lost connection with the PC, I tried a softreset and what I got was the tricolor scren with IPL / SPL data and RUU at the top right. I´m afraid that we have another G4 casualty...
And few hours later.......
I reflashed the phone with RUU_RIsidoro_2.26.10.2_WWE+CF2SP1_G4 this time it went to the 100% progress and the congratulation screen for a succesful flashing, however stalls in bootloader screen (this time without the RUU inthe top right), whenever I do a softreset (since the on / off button still is not working) The HTC innovation splash screen shows up, then disappears and my Wizard returns to the bootloader mode. I think I should be moving to the Wizard forums, thank you VJ!
Hey guys.
I cannot get this application to run on my dual! It just loads a black screen. It works though because I can slide to unlock it without being able to see the screen which isn't all that useful!
So is this just me?
Sam
Same problem on my Kaiser
Hi there!
I am having the exact same problem on my Kaiser phone.. :-(
Who can help?
Henk.
It's known bug with certain devices but here's a workaround disable Direct Draw:
Edit your registry, navigate to \HKEY_CURRENT_USER\Software\A_C\S2U2
Find the key DirectDraw and change the value from 1 to 0.
Funny enough on my dual I didn't have to do this tweak!
'slide' to unlock?
I assumed 'slide' to unlock was sliding the phone open..
after a couple of resets I found out that you had to 'slide' on the screen
I there really no way this to may it work with sliding the phone open,
thought this would be really nice..
Besides from this misunderstanding of mine it works fine, caller Id is very nice!
gfreek said:
It's known bug with certain devices but here's a workaround disable Direct Draw:
Edit your registry, navigate to \HKEY_CURRENT_USER\Software\A_C\S2U2
Find the key DirectDraw and change the value from 1 to 0.
Funny enough on my dual I didn't have to do this tweak!
Click to expand...
Click to collapse
Wow.
You are actually amazing for making that work!
You know, that may be one of the best answers I have ever recieved. Thank you so much
My Wing was doing this also. I changed the name from wallpaper.gif to Wallpaper.gif and it works fine now.
Worked!
Worked fine for me; thx!
works after the registry key change, but....
It works lousy if you activate the callerID. When you get a call , the internal phone app. takes over the S2U2, and after you finish the call the screen just remained in the position of the incoming call picture of the S2U2 and you cannot do anything except soft-reset. :-(
Does anyone has an idea or suggestion?
TIA/Zohar
sorry for my stupid q:
may i know why you choose s2u2 instead of the WM6 built-in key-lock feature? just due to big wallpaper instead of the Today screen, or some other great features attracted you?
Hey good question.
I prefer it because its a sleeker interface to go with a sleek device and also mainly because it annoys iPhone users that I know.
mini_man said:
Hey good question.
I prefer it because its a sleeker interface to go with a sleek device and also mainly because it annoys iPhone users that I know.
Click to expand...
Click to collapse
haha.. lol
i personally like the big caller photo most. yet i still can't make up my mind on using it for long term, because now sliding out the keypad can only wake up the device but no longer unlock it. and personally i still prefer using the green/red keys to answer/reject calls, which means the built-in key-lock feature can also do.
..and one more
It seems that all the keys and everything is locked except the iCube.
This can be activated even thouth the S2 is in keylock state.
zoharbl said:
It seems that all the keys and everything is locked except the iCube.
This can be activated even thouth the S2 is in keylock state.
Click to expand...
Click to collapse
(for Sprint Touch (Vogue) and Touch Dual (Nike))
you can lock the cube as well by adding this reg key:
[HKLM\Software\HTC\Biotouch\Disable4SpecificApp\S2U 2]
"ClassName" = "S2U2"
is the ' ' space at the end of the key name correct? 'S2U 2' or should it be 'S2U2'?
gmlogan said:
is the ' ' space at the end of the key name correct? 'S2U 2' or should it be 'S2U2'?
Click to expand...
Click to collapse
no space. just S2U2.
=======================================================================
New version 1.2 available here
=======================================================================
=======================================================================
Reviewed on gadgetmix.com: See the article
=======================================================================
If you have tried to play a game needing left and right key on an HTC Touch Diamond, you noticed that they are 2mm wide and if you click next to it, you get back to home page or to dialing menu etc...
So I've written a prog allowing you to lock these 4 keys actions and replace it by classical key event (VK_LEFT, VK_RIGHT, ...).
In that way you can play tetris, and use "Pick-Up" and "Hang-Up" keys for going left and right.
Link ->: DredSensor
To use it, you need:
1) An HTC Touch Diamond (it's the only one i have so i can't test it on other models)
2) Install the .cab
3) Reboot your HTC
4) Run a game (or app or ...)
5) Get your stylus out and back-in, in less than 1 second
6) Click "Yes"
----- A config window opens:
7) Check that Type = "HardKeySimul"
8) Click "Ok"
Now you can use (and eventually assign) your 'Home', 'Back', 'Pick-Up' and 'Hang-Up' keys in that game/app.
Actually, the 'Pick-Up' and 'Hang-Up' keys are always defined as Left and Right events.
Have fun.
Ps:
For people interested, the other "Type" in the config window are:
- "Launcher": allow you to quicklaunch 4 app (that you define in the config wnd) when you double tap (not click, just tap) on one of those 4 keyz
- "Scroll": allow you to scroll the current window by tapping those 4 keyz panel
- "KeySimul": allow you to send left/right/up/down events by tapping those 4 keyz panel
Sounds Great, will give a try....
If you can make this buttons to be assinged to other apps the whole time you'll be a hero
palmbluetooth said:
Sounds Great, will give a try....
If you can make this buttons to be assinged to other apps the whole time you'll be a hero
Click to expand...
Click to collapse
In fact if you launch /Program Files/DredSensor/DredSensorCfg.exe, you can edit the "Default" config that applies every time no other config matches...
So if you set the Default config in "Launcher" mode, you can quicklaunch app from everywhere...
Actually, the Launcher mode works with "double tap" rather than click. But i can update it quite easyly to make it work on click if you want.
Dredger, can't wait to try this. This is my biggest gripe when playing games, and I didn't even think to post on here to see if someone could come up with something. I'll test today and let you know how it works!
Very Nice App, really works well.
The only thing is that I don't know how to add 'start', 'ok', answer and hang up to the buttons, do you have any suggestions?
Thanks, I'm loving it.
not able to download. all it gives me is a lot of squares and nothing else.
clever idea, finally i can play racing game on my diamond, thanks!
A very nice and welcome idea. Unfortunately, it doesn't work with my Raphael. Tried it with Kevtris: succesfully installed, soft-reset, started the game, and configured DredSensor for the game, but when I push e.g. the phone up key, it still brings up the phone application. I didn't change any of the settings in the DredSensor config screen (I did check that "HardKeySimul" was selected).
Hope you can make it work for Raphael too, it is so annoying trying to play games with the d-pad, when you accidentally press the home/phone/etc. keys all the time.
Work perfect on Diamond but... it doesn't work on Touch HD... (error.. Unable to load HTC API DLL)
aBE-One said:
A very nice and welcome idea. Unfortunately, it doesn't work with my Raphael. Tried it with Kevtris: succesfully installed, soft-reset, started the game, and configured DredSensor for the game, but when I push e.g. the phone up key, it still brings up the phone application. I didn't change any of the settings in the DredSensor config screen (I did check that "HardKeySimul" was selected).
Hope you can make it work for Raphael too, it is so annoying trying to play games with the d-pad, when you accidentally press the home/phone/etc. keys all the time.
Click to expand...
Click to collapse
pinele said:
Work perfect on Diamond but... it doesn't work on Touch HD... (error.. Unable to load HTC API DLL)
Click to expand...
Click to collapse
Sorry, i only have an HTC Diamond so unless you offer me a Raphael or HD, it's quite hard for me to check anything.
For the touch HD, maybe you should download HTCAPI.DLL somewhere, put it in /Windows and try again.
For the Raphael, on the related article on gadgetmix.com (see 1st post for the link), it seems it works on HTC Touch Pro so it should work on yours.
palmbluetooth said:
Very Nice App, really works well.
The only thing is that I don't know how to add 'start', 'ok', answer and hang up to the buttons, do you have any suggestions?
Thanks, I'm loving it.
Click to expand...
Click to collapse
Sorry, i think i don't understand exactly what you would like to do...
Start, Ok etc are default functions on that buttons so you have nothing to do to get them doing that...
Thank You
Hey! This looks like a really good program idea. Its not all that simple to figure out. I'm also not too sure there is an alternative way to customize the program.
Once I had it figured out, it works really well. Kudos for the update. My Diamond is getting much more reading use now. I just found that the d-pad was pretty much useless until now.
Also kudos on the stylus idea. Pretty nifty way to activate the menu.
Two thumbs up. I'm looking forward to any updates in the future.
Dredger97 said:
For the Raphael, on the related article on gadgetmix.com (see 1st post for the link), it seems it works on HTC Touch Pro so it should work on yours.
Click to expand...
Click to collapse
Well, maybe they're using another ROM or something. Are you sure they tested it with a Raphael? Maybe they just tested it with a Diamond and presumed it would work on a Raphael (I'm not familiar with the site, so I don't know what devices they're using).
Anyhow, after some more testing, it is actually partly working. That is, sometimes the phone/hang up buttons work as left/right, sometimes they don't. With the phone button it's about 50 % working, 50 % not (in Kevtris). For some reason the hang up button is working more frequently, something like 80 % working, 20 % not.
Also tried it with another game - Marble Worlds 2 demo - again only a part of the key presses are registered correctly.
I understand it's hard for you to test anything when you don't have a Raphael, but if I can do anything to help (apart from donating my Raphael to you ), just ask.
aBE-One said:
Well, maybe they're using another ROM or something. Are you sure they tested it with a Raphael? Maybe they just tested it with a Diamond and presumed it would work on a Raphael (I'm not familiar with the site, so I don't know what devices they're using).
Anyhow, after some more testing, it is actually partly working. That is, sometimes the phone/hang up buttons work as left/right, sometimes they don't. With the phone button it's about 50 % working, 50 % not (in Kevtris). For some reason the hang up button is working more frequently, something like 80 % working, 20 % not.
Also tried it with another game - Marble Worlds 2 demo - again only a part of the key presses are registered correctly.
I understand it's hard for you to test anything when you don't have a Raphael, but if I can do anything to help (apart from donating my Raphael to you ), just ask.
Click to expand...
Click to collapse
You probably run another program that uses the same sensor API and that conflict with DredSensor.
Don't you have G-Scroll or something similar installed?
Is it possible to assign the home and back hardware button to make left and right soft keys?
aBE-One said:
A very nice and welcome idea. Unfortunately, it doesn't work with my Raphael. Tried it with Kevtris: succesfully installed, soft-reset, started the game, and configured DredSensor for the game, but when I push e.g. the phone up key, it still brings up the phone application. I didn't change any of the settings in the DredSensor config screen (I did check that "HardKeySimul" was selected).
Hope you can make it work for Raphael too, it is so annoying trying to play games with the d-pad, when you accidentally press the home/phone/etc. keys all the time.
Click to expand...
Click to collapse
On my Raphael program works perfectly. My ROM is PROven ROM 1.09 PLK.
Claus72 said:
Is it possible to assign the home and back hardware button to make left and right soft keys?
Click to expand...
Click to collapse
Not in that first version but as it seems people find it usefull, i'll probably update it to let you choose which key or app-launch you affect to each button.
Dredger97 said:
Not in that first version but as it seems people find it usefull, i'll probably update it to let you choose which key or app-launch you affect to each button.
Click to expand...
Click to collapse
When you do that, can you consider left and right softkeys? That'd be a significant advantage, as I find the lack of the two keys annoying in some apps (esp java ones).
On a side note, does the software poll for input? While I doubt it would affect the battery that much, I'll probably limit my usage to be on the safe side.
Great app!
g2tl said:
When you do that, can you consider left and right softkeys? That'd be a significant advantage, as I find the lack of the two keys annoying in some apps (esp java ones).
On a side note, does the software poll for input? While I doubt it would affect the battery that much, I'll probably limit my usage to be on the safe side.
Great app!
Click to expand...
Click to collapse
So if I understand, you'd like the possibility to simul left or right softkey by clicking on 'Home' and 'Back' for example?
On the side note, it doesn't poll for input, but it polls every second to check which app is on the foreground. The input job is event based.
Dredger97 said:
So if I understand, you'd like the possibility to simul left or right softkey by clicking on 'Home' and 'Back' for example?
Click to expand...
Click to collapse
correct
On the side note, it doesn't poll for input, but it polls every second to check which app is on the foreground. The input job is event based.
Click to expand...
Click to collapse
Which I'm assuming is not happening when the screen is off (through power button)?