How to stop screen on when new sms arrives? - JAM, MDA Compact, S100 General

Hi every one.
So i set "button lock" and also disable mainly all notifications but every time a new sms arrives,the screen goes on.I will like to keep the screen off because if you carry your magician in your pocket and after that sms arrives,you can accidentaly press any button or even touch the screen.
I been checking every thing i could check but i can´t find the answer about this problem.
Thanks in advance.

Third party software Pocket Zen Phone or phoneAlarm.

Ok i´ll check it and see what i can do.
Cheers mate.

User22 said:
I will like to keep the screen off because if you carry your magician in your pocket and after that sms arrives,you can accidentaly press any button or even touch the screen.
Click to expand...
Click to collapse
There are many occasions the Magician turns on its screen. Rather than trying to find and disable all these, I copied TPDisable.exe and TPEnable.exe from the original Extended ROM into my Program Files folder, and then assigned them to a hardware key (using Hotbutton, so that I can use the same key for both).
As the name implies, TPDisable disables the touchscreen (not the display!), and TPEnable re-enables it. So, before I put my Magician into my pocket, I now disable the touchscreen (one press of a button). That still leaves the keys active, true, but I found that normally the touchscreen is much more likely to be the culprit when strange things happen on your Magician while it's in the pocket, and turned itself on.
Cheers
Daniel

@ tadzio
Well,that is a very interesting solution,but i can´t find TPDisable.exe
or TPEnable.exe inside my magician.I need a bit more info from you
Daniel.
Thanks a lot for your replies.

What happens if you hold down power button for 2 seconds to switch off backlight? Does the light still illuminate on receipt of sms?

@ cruisin-thru
I can´t see the point of your question,mainly because the thing i am looking for is to "switch off" my Qtek like a normal mobile phone,i mince buttons locks and screen off when a new sms or incoming call arrives and when you push power button for example,then screen go on and also release the lock of the buttons.
Any one can say that then i can use deltalock.I did it but the battery live is going down very quick.
Screenlock is not working properly also,i will say that Deltalock is 95% a lot better than Screenlock.
And finally,why microsoft is developing this OS without fully screen off selectable option???. Who knows!!!
Cheers

User22 said:
Well,that is a very interesting solution,but i can´t find TPDisable.exe or TPEnable.exe inside my magician.I need a bit more info from you Daniel.
Click to expand...
Click to collapse
Both programs are in the Extended ROM. Most users have made this visible (though not writable) by performing a Hard Reset, and immediately after completing the initial screen adjustment and mini-tutorial and before the device starts installing programs, a Soft Reset.
If you do not want to do a Hard Reset, search this site's FTP server for Magician Extended ROM downloads. There were a few there last time I looked.
Cheers
Daniel

Well,after config hotbutton to TPDisable and TPEnable i can´t enable the screen and hardware buttons.
TPDisable is disablind the screen but also all the hardware buttons ( with and without button lock at settins),even the power button.
I use same hardware button for TPDisable and TPEnable ,is that correct or i am doing silly things?

If I arrive an sms the screen is switching on and after a few seconds switching off again if I don't press any key or tap the screen!
It's a changeable registry key:
HKEY_LOCAL_MACHINE / System / CurrentControlSet / Control / Power /
WakeupPowerOff =12 (the default is 180)
DisableGwesPowerOff=0 (the default is 1)
If you switch on the Jam (power button) need to press some other key too, because it switches off after 12 seconds!!!
by Avers

@avers
Well that is another solution but i insist that there should be an easiest way to keep the screen fully off when a new sms or what ever arrives,including hardware buttons off ofcourse.
Any suggestion more?, perhaps at the end and betwen all of us ,we can find the solution.
Cheers.

I think the best solution is third party software like PHONEALARM,
it's easiest way to get main tweaks of Pocket Windows.
get it there
http://www.pocketmax.net/phoneAlarm.htm

Well my friends,pocketzenphone is not doing what i am looking for.
Next step is to try phonealarm,but probably will work the same way as pocketzenphone,leting the screen to go on every time a new sms arrives.
Sorry for my languaje but F... microsoft and F... devil gates.

As you can read on this post ,phonealarm IS NOT doing it.
http://www.pocketmax.net/phpbb2/viewtopic.php?t=429

phonealarm has option named "Don't activate backlight on alarm"
ALARM there means any event, that needs notification.
now i am understanding, that it is some differ that you need.
also i advice you make some registry tweaks to make a very short backlite time when sms arrives.:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Power\WakeupPowerOff = 10
this timeout in seconds. is used when our device self power on, when SMS arrives or we push the POWER button and do nothing anymore
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Power\DisableGwesPowerOff = 0
this key is enables this power control system (necessarily change it, or first key will not work)
after the editing registry you need to reboot PDA.
sorry for poor english, i translate text from russian.
if you want to use online translator i can give you original URL
_http://forum.ladoshki.com/viewtopic.php?t=16012

Thank you for your reply i will try like you and others point out and also will keep looking for that utopic soft.

deltaLock locks the screen and buttons even if you get sms or calls. I use it on my JAM and it works so far.

bnycastro said:
deltaLock locks the screen and buttons even if you get sms or calls. I use it on my JAM and it works so far.
Click to expand...
Click to collapse
If you read one of my post ,you will see that i allready said that Deltalock is working but it is KILLING the battery live very fast and when i say VERY FAST it mince that you will get almost 6hours against the normal live (more than 15hours).
Cheers mate.

I think if you keep your ppc on all the time you will get this battery life. Anyway I think deltaLock is for keeping your PPC on and having screen and button lock, not having it in suspend mode and not allowing the screen to power up. Sorry about that, seem to have misunderstood your post.

Don´t worry mate, at the end we are all together trying to find a solution to this microsoft silly programing, any comment and any new idea is wellcome.
Cheers.

Related

anyone know if you can lock the touchscreen ?

Hi all,
when you got the screen folded over and facing out, any way of locking the screen?
thanks
ross
I was also woundering about that...
when you have the screen in phone mode, there must be some way of locking the screen!
well if nobody here knows, o2 won't know!
Not sure if this answers your question but mine is set up thus:
In 'Settings/Buttons/Lock' set 'When device is off' to 'Lock all buttons except Power Button'
I keep the screen outwards and use the power button to lock/unlock.
One snag is that the phone seems to unlock itself when receiving an incoming call. I therefore can accidently cancel it trying to get the damn thing out of my pocket.
I do believe it locks the screen during installation of the ext rom..
This is done by running tpdisable.exe from the windows directory..
A word of warning though: IT'S DISABLED!
Unless you bind tpenable.exe to a button FIRST, you're screwed..
(Ok, a soft reset should fix it..)
I think they are called tpenable and tpdisable...
I don't have the device yet, so I can't check right now.
When I was looking at the config file, there was no mention of an exe, it was like a command (unlock your ext rom and take a look at it).
I got the impression this function was now embedded in the OS hence no exe. Probably wring of course....
Then it should be possible to make such a program, and assign it to a button..
Tried this one?
http://www.freewareppc.com/utilities/screenlockforpocketpc.shtml
could maybe work for your devicetype to
Hello,
pimbo said:
Tried this one?
http://www.freewareppc.com/utilities/screenlockforpocketpc.shtml
could maybe work for your devicetype to
Click to expand...
Click to collapse
Any one work out what the key combination is to diactivate it on the Universal?
TIA
I guess it would be the equivalent keys of leftmost and rightmost keys on HTC Blue Angel ('Windows' and 'Ok' keys!?)
However you guys, should try MortSaver (freeware also)
http://www.sto-helit.de/modules/wmpdownloads/viewcat.php?cid=7
At least you can set several parameter according your preferences.
I just found an issue related with Voice Speed Dial interworking.
Hello,
Conchas said:
... However you guys, should try MortSaver (freeware also)...
Click to expand...
Click to collapse
Many thanks, I like it!

Remapping the volume slider?

Has anyone figured out how to remap the volume slider on the Wizard?
I hardly ever want to change volume, just turn on/off vibrate mode which is a single keypress anyway, but i would really like it to be an up/down control like my old Dell Axim.
I know it functions like this in IE full screen mode, but I really want it for everything (especially MS Reader).
I think a lot of people would like this. It allows a better grip on the phone whilst moving within the app you're using (eg: MS Reader).
Any guru's got an idea about this one?
Joe
Remapping
Absolutely neccessary thing to fix (volume slider)!
And as using double-language hard-keyboard layout I am in desperate need to remap the change-layout sequence.
What about remapping in this OS, is it possible to do something?
Someone did this on the Magician (found it in that group on here at the time), I remember finding it very useful!
If someone could do a Wizard version that would be great!
Solution Found
Here is how you do it (and it was on the Magician forums, thx for the tip :wink: ):
Install the program found at the URL below, or from the attachment as you wish.
When you get the setup screen, choose "Do not handle" for all except the volume slider, which is set to up/down.
Ok it, and there you go, slider is now up/down and works in MS Reader, Today screen, and general folder browsing.
It says on the site not to put it on any device not listed as compatible, which doesn't include the Wizard, but "He who dares, wins..."
I am well chuffed with it. Now I am all ready for my commute on Monday.
http://ae.inc.ru/download/AEBPlus.zip
Joe
Unless this is a new version. DO NOT USE AEB+ WITH A WIZARD
I tried AEbuttons plus awhile ago and It deleted a couple of my buttons. I dont think it is meant for a device with as many buttons as the wizard. I had to go in and manually create the buttons again. I told it to handle all buttons though. Maybe telling it to only handle the volume slider doesn't cause this problem. I won't try it again until they actually say the wizard is compatible.
I just checked all buttons having read your post.
The only casualty is the connection manager button, which now only switches from audio vol. on to vibrate ringers when held down, and I have an icon on the today screen to go there anyway.
I can live with that
BUT BEWARE: No comms manager button = no hard reset = what do you do when you need to hard reset?
guttrhead said:
Unless this is a new version. DO NOT USE AEB+ WITH A WIZARD
I tried AEbuttons plus awhile ago and It deleted a couple of my buttons. I dont think it is meant for a device with as many buttons as the wizard. I had to go in and manually create the buttons again. I told it to handle all buttons though. Maybe telling it to only handle the volume slider doesn't cause this problem. I won't try it again until they actually say the wizard is compatible.
Click to expand...
Click to collapse
How did you restore the buttons?
Never mind:
http://forum.xda-developers.com/viewtopic.php?t=33795
joebongo said:
The only casualty is the connection manager button
.....
BUT BEWARE: No comms manager button = no hard reset = what do you do when you need to hard reset?
Click to expand...
Click to collapse
I just checked if it is possible to restore the connection manager button after installing AE Button Plus, and it seems to work
Just add these registry keys after you have installed the software and you have all your buttons back and an up down slider:
Code:
[HKEY_LOCAL_MACHINE\Software\Microsoft\Shell\Keys\40C6]
"Flags"=dword:00000000
"ResetCmd"="\"\\Windows\\AppButtons\\Comm Manager.lnk\""
"Icon"="\\windows\\CommManager.exe, 0"
"Name"="Button 5"
@="\"\\Windows\\AppButtons\\Comm Manager.lnk\""
[HKEY_LOCAL_MACHINE\Software\Microsoft\Shell\Keys\40C5]
"Flags"=dword:00000000
"ResetCmd"="\"\\Windows\\AppButtons\\Record.lnk\" -b"
"Icon"="\\windows\\HotVoice.exe, 0"
"Name"="Button 4(Hold)"
@="\"\\Windows\\AppButtons\\Record.lnk\" -b"
You can put this in a .reg file and open it on your Wizard to import into the registry
I don't think Windows minds the button to be remapped for a hard reset, the hard reset will probably still work if the button is remapped by software.
Did you figure out which reg entries are actually changed when the slider is remapped by AEB? If we can figure this out, we could create a file to do this without the need to recreate.
I am also getting slowdowns/crashed on syncing via USB, and am beginning to wonder if this is another AEB effect.
Joe
joebongo said:
Did you figure out which reg entries are actually changed when the slider is remapped by AEB? If we can figure this out, we could create a file to do this without the need to recreate.
I am also getting slowdowns/crashed on syncing via USB, and am beginning to wonder if this is another AEB effect.
Joe
Click to expand...
Click to collapse
I can't find any slider registry entries, but I have no idea where to look
I have noticed that once I close the AEB program my slider doesn't do anything anymore, so it might be possible that it is not just a registry entry

AWESOME: Vibrate feedback on phone key press

faysel, over at the modaco forum has come up with this awesome cab that lets you get vibrating feedback everytime you press one of the number buttons in the phone. The vibration lasts as long (or as short!) as you press the button.
Great cab, very useful for knowing whether you have indeed pressed the key.
This is great, thank you. I used to use Redial with vibrating effect on my PDA2k (WM2003SE) but this is even better
don't expect a long battery life with that! :wink:
acer175 said:
don't expect a long battery life with that! :wink:
Click to expand...
Click to collapse
Are you kidding me? I mean what kind of a battery effect you think it will have? Its such a small vibe that I don't expect to have ANY noticable effect on battery life. First it vibes only when you dial phone numbers (how many a day? 5? 6? even 20? Its still nothing. Second, receiving a phone call, that is the vibration during it, probably uses more power than this addition will use in 20 calls...
I really disagree... :wink:
This is a great little program!
I don't like it because if you tap fast, it wont vibrate. In addition to this, there is a serious problem with the dialer after you uninstall it.
So I had to reinstall it and now i'm stuck with it
My rating : 0 (ZERO)
@Andrew_sh: use the attached cab to get the keytones back, then uncheck from the sounds and notifications settings to get a working silent dialer back.
@Koksie
Thanks for trying but unfortunately it won't fix it.
When I press the button , the tone will sound but if I press it again shortly after, it lags and makes a higher pitched tone.
Sorry to hear it didn't work Andrew, I have no idea how to fix this. I use the vibrate and am happy with it, on my Magician going back with this cab worked fine, I have no idea what is causing this in your Prophet. I hope you can figure it out and correct it, good luck with that.
andrew_sh said:
@Koksie
Thanks for trying but unfortunately it won't fix it.
When I press the button , the tone will sound but if I press it again shortly after, it lags and makes a higher pitched tone.
Click to expand...
Click to collapse
Try this, it's a saved registry string of the original keys that the .cab modified. Hopefully i'll work for you without messing up anything else.
I had to rename the file vibrate off.reg.exe to ba able to attach it. Just delete the .exe part ie. vibrate off.reg
this is a technical forum
can someone paste here the registry keys which are being modified by this vibrate utility?
thanks
Using a registry editor navigate to the following keys and follow the directions. Do this for each of the listed registy keys
1. Rename Standard DWORD parameter "Sound" to "Sound1"
2. Create new String Parameter "Sound"
3. Assign value *vibrate* to this new parameter.
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf#
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf*
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf0
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf1
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf2
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf3
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf4
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf5
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf6
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf7
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf8
HKEY_CURRENT_USER\ControlPanel\Sounds\Dtmf9
this mod doesn't work fine for me, I noticed the vibrate a few time but it's not working everytime I tap on the Keypad...
Strange :?
Although the mod works fine, I had big troubles removing it again.
After removing the mod with the supplied cab file any keys pressed in the dialer would lag and emmit a short beep.
i finally succeeded in removing it manually:
First reinstall the vibrate mod again so that the keys vibrated again when pressed.
Then go into the registery keys posted above, deleted the parameter "Sound" and then rename the parameter "Sound1" back to "Sound".
Do this for all Dtmf keys.
Thats all
its true if you tap fast it wont vibrate at all.. very annoying. is there a way to make it vibrate for a set lenght.. much like the dtmf tones used to be.. no matter how long or short i press..
that would be very useful.
regards,
tom
bk227865 said:
Although the mod works fine, I had big troubles removing it again.
After removing the mod with the supplied cab file any keys pressed in the dialer would lag and emmit a short beep.
i finally succeeded in removing it manually:
First reinstall the vibrate mod again so that the keys vibrated again when pressed.
Then go into the registery keys posted above, deleted the parameter "Sound" and then rename the parameter "Sound1" back to "Sound".
Do this for all Dtmf keys.
Thats all
Click to expand...
Click to collapse
I used this mod until I found out that I couldn't turn off vibrate on incoming calls anymore. I can't be sure that they are related, but the timing was right. The next time I did a ROM upgrade I didn't install it again. I use speed dial with Photo Contacts Pro anyway.
krale said:
faysel, over at the modaco forum has come up with this awesome cab that lets you get vibrating feedback everytime you press one of the number buttons in the phone. The vibration lasts as long (or as short!) as you press the button.
Great cab, very useful for knowing whether you have indeed pressed the key.
Click to expand...
Click to collapse
Never mind - problem fixed
Not installing on Tytn / Black2.5
"Installation unsuccesfull, Not meant for this device"
Did anybody have more luck? How?
I don't like this
...the vibrate just doesn't trigger some of the time, which means you can't rely on tactile feedback on dialling, which makes it fairly useless. Sorry...
buhahahaha
*buzz* *buzz* *buzz*
works fine on my Jamin. Great app

Hard buttons config

Hi all
Can anyone send me the following registry key (and subkeys) please (of the HTC TyTN / Hermes)
HKLM\SOFTWARE\Microsoft\Shell\Keys
I have a problem with my power button and I've discovered that some values are missing in this registry key.
P.S.: If possible, please send me the configuration from an original rom without any third party software.
Many thanks!
nero said:
Hi all
Can anyone send me the following registry key (and subkeys) please (of the HTC TyTN / Hermes)
HKLM\SOFTWARE\Microsoft\Shell\Keys
I have a problem with my power button and I've discovered that some values are missing in this registry key.
P.S.: If possible, please send me the configuration from an original rom without any third party software.
Many thanks!
Click to expand...
Click to collapse
Hopefully Keys attached
Mike
many thanks Mike
but "Button 6" configuration is missing... is that alright?
by default there is no configuration for this button?
nero said:
many thanks Mike
but "Button 6" configuration is missing... is that alright?
by default there is no configuration for this button?
Click to expand...
Click to collapse
Yes, until now I had not noticed that but that is indeed true on mine. I have also not carried out any customisation or even reset any of these buttons (well since last HR anyway)
Mike
Hi again Mike!
Ok, I've deleted the "HKLM\SOFTWARE\Microsoft\Shell\Keys\40C5" key and now the power button works perfectly.
I have wisbar advance 2 installed and probably, somehow I think, messing arround in his settings has created the power button mapping and that makes his behaviour anoying...
Maybe this is a solution for some other people with this problem. I've seen there are more people in the forum with the "power button problem".
Many thanks.
Power Button
Good news.
Had not seen others with the problem of the "power button" but if I spot them I'll link to here and by repeating power button problem hopefully searches will lead here!!!!
Mike
checkout this one here
people saying that need to do a soft-reset...
is what I have been doing when the power button get stucked and it is not anymore
nero said:
checkout this one here
people saying that need to do a soft-reset...
is what I have been doing when the power button get stucked and it is not anymore
Click to expand...
Click to collapse
Well now, I wonder!
Perhaps you could write up a detailed piece on exactly what was happening and then the exact detail of what you did/changed. I have a pretty good picture but if you get the time the old blow by blow account would be useful.
Cheers
Mike
going to bed now-enough problems for one day!!!
Mike,
sorry but I dont know exactly what you want to say with "old blow by blow account". My native language is not english and I dont know that expression.
I can say that my power/toggle screen button becomes "non responsive" in the past couple of days, sometimes works after 3/4 presses or after a long press but other times I need to do a sw reset pressing with the stylus in the reset button/hole.
What I did to fix this malfunction is what I've described in this thread's 5 post (here)
I've used resco's Registry Editor and deleted the key "HKLM\SOFTWARE\Microsoft\Shell\Keys\40C5" and all of it's contents.
Now the power/toggle screen button works perfectly!
If you need some more information, just do has one of our tv commercial
"explains it as if I am too much donkey"
Cheers,
Nero
I'm from Portugal.. same GMT, sweet dreams
Would this make it in a wizard too?
Hi guys, I have a wizard with the power button inoperant, everything else looks work fine... I tried several tricks given in the forums and those are great to power it off but not for turning on the phone niether the display on. Would this make it in the wizard too?
Luiggi, take a backup of your registry (Everyone should before registry editing), and just try it!
V
Hi Guys,
does anyone know how to reconfigure the video-call button (the little button above the green button). I don't use this one, en would like to give it another function)
Thx!
Thanks VJ
vijay555 said:
Luiggi, take a backup of your registry (Everyone should before registry editing), and just try it!
V
Click to expand...
Click to collapse
Thank you Vijay I took a look to the 8125 registry and is quite different, i´m afraid this wouldn´t work for the Wizard. I´ve tried also a couple of your programas (VJKeypress and VJEscahaton) but can´t help either, my problem is to turn the phone on (i´ve been using softreset during a connection to the power supply) and all indicates that this is a hardware issue... any thoughts?
Take a full backup (eg SPB Backup) then hardreset. Test if a clean rom still has the problem. If it does, it's a hardware issue, get it repaired.
Otherwise, if it's software, list what you've got or rebuild your installation.
V
It died like a hero....
vijay555 said:
Take a full backup (eg SPB Backup) then hardreset. Test if a clean rom still has the problem. If it does, it's a hardware issue, get it repaired.
Otherwise, if it's software, list what you've got or rebuild your installation.
V
Click to expand...
Click to collapse
I follow your advice and @ 80% of flashing stalls for awhile with the progress bar in red, after some minutes proceeded turning the progress bar in blue color and @ 95% progress I got ERROR326 : INVALID COMMAND "With the legend "This NBF file can not be used for your phone. Please check your NBF file" The screen was white with the 95% progress bar and lost connection with the PC, I tried a softreset and what I got was the tricolor scren with IPL / SPL data and RUU at the top right. I´m afraid that we have another G4 casualty...
And few hours later.......
I reflashed the phone with RUU_RIsidoro_2.26.10.2_WWE+CF2SP1_G4 this time it went to the 100% progress and the congratulation screen for a succesful flashing, however stalls in bootloader screen (this time without the RUU inthe top right), whenever I do a softreset (since the on / off button still is not working) The HTC innovation splash screen shows up, then disappears and my Wizard returns to the bootloader mode. I think I should be moving to the Wizard forums, thank you VJ!

Disable Hardware Keys

Hi Folks,
I´m still looking for a way to disable the hardware-keys while the devide is in sleepmode. Only the Powerbutton should wake up the device. And also only the screen-slider should answer or dismiss an incoming call....
I cant believe that there ist still no solution for this problem....
And please dont answer me with: use s2U2 or other 3rd Party stuff... there must be an other way to do so
Candy-men said:
Hi Folks,
I´m still looking for a way to disable the hardware-keys while the devide is in sleepmode. Only the Powerbutton should wake up the device. And also only the screen-slider should answer or dismiss an incoming call....
I cant believe that there ist still no solution for this problem....
And please dont answer me with: use s2U2 or other 3rd Party stuff... there must be an other way to do so
Click to expand...
Click to collapse
you have to.
I'm also interested in this. Why wake up the phone with another button then the one who put it in sleep in first place. I find it strange. Like if I put the light off in the kitchen then opened the fridge the kitchen light will come on. who would like that ???
Can someone find a solution for this I search everywhere with no satisfying result.
I newly updated my Topaz from 6.1 to 6.5.3 and I can't recall that I had this problem in 6.1 and i had 6.1 for over 1 year.
I would say that this issue has nothing with screen lock to do it's rather an issue with wake-up (What shall wake up the phone from sleeping status : a call, sms, mms, mail, hardware key, power button etc...)
Just when I decided to post my problem I found it's solution:
Set HKEY_CURRENT_USER\ControlPanel\Keybd\DefaultKeyLock to 0.
Now nothing wakes-up the phone except the power button.
I found a cab posted also here is the link : http://forum.xda-developers.com/attachment.php?attachmentid=246722&d=1258236796
found on page : http://forum.xda-developers.com/showthread.php?t=581531&page=2
posted by : triperko http://forum.xda-developers.com/member.php?u=393396
i´ve made the changes in the registry, but still every button wakes up my device. So this "tweak" won´t work for me
Well I know after posting for about 3 - 4 hours I got the problem back myself not understanding what I have done to get the problem back. Yesterday evening I spent all night trying to figure this out. I have CHT Lock screen enable + BharS_OBOE_Lock_Disable.Cab. I need this cab because I have Huashan lockscreen built in my rom. And the cab allows me to use the CHT lock screen. To solve my problem I have done the following:
1) Disable CHT lockscreen
2) Uninstalled the Cab
3) made sure the registry setting was there and problem solved.
3.1) reinstalled the cab
3.2) enabled the CHT Lockscreen
Still working...
4) Went to power option the win 6.5 setting just to take a look (didn't change a thing)
5) Problem returned.
Start all over again to solve my problem.
For now on I'm staying out of the power option in win 6.5 setting.
There is nothing you can do there anyway until CHT lock screen come with an option for enabling password on lock.
I'm sorry I don't have any scientific explanation for this. But till now I can say I have solved my problem hope it solves yours
I'm using WWE"Topaz Roms + Kitchen"Build 23130/21914"Manila 2.5.20182814.0"(August 20th)
No, this couldn´t solve my Problems, because i use CHT 1.6.1 and this version doesn´t have any Lockscreen options.
The real Point that i can´t understand is: This is still a WinMo 6.5 Version, why is the Menue-point : Lock all buttons except Power on/off not there?
There must be a way to get this point back. I can´t belive that we have an extra written WinMo Version for the HD2...
So, where is the registry setting to get back the point?
+1000
I also hate this problem with HD2 FYI. I had already opened a post on this a few weeks back.
http://forum.xda-developers.com/showthread.php?t=694109
Have your tried uninstalling CHT making sure the reg key above is set and Test ?
this needs to happen... any key to wake is just silly! and on a related point, only the on-screen slider should answer/reject an incoming call

Categories

Resources