Dear all, this mornig I can't async my mini. It says cannot connect due to error 608. Any ideas ? Soft reset does not seem to work. Thanks.
have you installed a wifi card ??? I had such a problem when I was trying to setup my Spectec Wifi card...
Yes, I did install a wifi card which worked for about two days. Then there were some problems which led me to install the modified E300 Socket driver (I am not mistaken). It worked fine for about two days till the latest problem. Managed to solve it by doing a hard reset.
As far as wifi I am using the spectec driver for dopod version 1.24.2. Its only been a day, hopefully it works. The universal is not on these shores just yet... :lol:
Yes, I did install a wifi card which worked for about two days. Then there were some problems which led me to install the modified E300 Socket driver (I am not mistaken). It worked fine for about two days till the latest problem. Managed to solve it by doing a hard reset.
As far as wifi I am using the spectec driver for dopod version 1.24.2. Its only been a day, hopefully it works. The universal is not on these shores just yet... :lol:
Related
I just upgraded TMO radio stack to 6.24.00, works flawlessly. Tested the RS with calls, web connections, incoming call while on web ... perfect.
However, ActiveSync will not recognize a partnership with my PDA now. Reverts to Guest every connection.
Reinstalled ActiveSync ... no luck. Soft reset PDA ... no luck. Tried it on a WinXP-HE and Win2K computer, same on both.
Have searched forum & seen a few enteries on this subject but no solutions. Running TMO ROM 4.00.21 & TMO RS6.24.00.
Anybody had this issue & successfully resolved it?
Yeap been there seen that but had forgotten about those problems until I read your post! :wink:
Try downgrading back to 3.7, my sig states what I ended up doing to fix it for me! :wink:
Also you might try turning the device off before you put it in the cradle
so times that helped if I remember correctly.
HTH
Resolved problem by uninstalling ActiveSync 3.7.1, restart Windows, reinstall ActiveSync 3.7.1 and it detects new USB hardware, starts the Partnership wizard and things are okay.
I have loaded this program on my JAM, and it keeps resetting, can not use the device at all!
I DIDN'T HAVE ANY PROBLEMS WITH VERSION 1.11
Has anyone experienced the same problem? Any solution?
Thank you
It works fine on my blueangel.
You may try to hardreset your machine and install it again.
I have updated the rom and installed right after, reset and so on and still didn't work.
I have repeted this about 4 times with different ROM's
A.
Its working fine on my Qtek S100 with 1.11.00.WWE; its just a pig and insists on being installed in main memory - everytime I try to move anyof the DLLs to Storage, I have to do a hard reset..
Hi!
I am also using BatteryPackPro v.2. The problem I am facing is that sometimes when I am connected to my computer thru BT, the program memory on my Jam keeps decreasing. It keeps going down and when I disconnect it just stays at the same point till the time I do a soft reset.
Any suggestions?
there is an update 2.0.3
the update fixed the mapping of botton
Hi!
I´ve this problem... is it possible to re-install the drivers for the wifi built-in adapter in a BlueAngel?
Yesterday, after releasing the PDA from its cradle, I started to have this error message: "UNKNOWN CARD IN SOCKET 1 - Enter the name of the device driver for this card. For information, see the card manufacturer´s documentation"
And the message appears even if there´s a SD card inserted or not... and I´VE NOT WIFI.
It seems the PDA don´t recognize the wifi module... as if it was turned off...
I´ve updated to the latest ROM, latest radio etc... (i´ve not tried with WM2005 yet) and this happens again and again...
If there´s a way to acquire the wifi drivers (as it´s possible to have the BT drivers in a update), i´d like to reinstall them...
Anyway, could this be a hardware problem? (i mean, bad mainboard - module connection or something...?)
thanks in advance!!!
Hello all,
I have bought qtek S200 recently and i have spent a lot of man hours trying to get this thing to sync with my desktop computer. it works fine with my laptop however doesn't want to sync with my desktop.
I get an new hardware wizard when i plug my pda into the USB requests for me to point to the drivers because windows was unable to find drivers.. I have gone through troubleshooting steps where disabling firewall / ant virus. Uninstalling active sync reinstalling / downgrading active sync and upgrading no luck. doesn’t matter if i try 3.8 or 4.2 it doesn't want to recognize my device and asks for the drivers.
i have windows xp with service pack 2 installed. so at this point i am wondering if someone has the driver files for it ? or what should be next step, any help would be appreciated.
Don't even try with activesync 3.8. It doesn't support WM5. Use 4.1 or 4.2...
Can't help beyond that...
I tought I had tried everything as well, when I found this utility over at Modaco (apparently included in the latest Dopod ROM).
Install and switch from RNDIS to Serial using the program and voila - worked like a charm for me!
Hope it helps!
After fighting with this device and my system for about 2 weeks. i noticed that my system had become so unstable that it wont' accept any new hardware. I tried installing a new 3COM network card and mostly 3com NIC's dont' require drivers however my system poped a window stating can't find drivers and put the device in system not working properly status.
so then i decided to format my computer and after the format, installed service pack 2 for xp and tried ACTIVE SYNC. without a problem it worked fine.
Hi,
I have a Dopod 828+ upgraded to NL1.13 ROM +1.13 Radio + Big Storage. Tried to use my Spectec WIFI card(802.11b) with spectec drivers(SDW 820 for PPC 2003) but without success as it could not detect any network at all. Found another driver, mod E300 driver & wifi companion, in this forum and tried using it as well but it still give me the same problem. When i uninstalled my original spectec drivers, i have also completely remove the registry string as well. Am i missing out any more steps? Any advise?
Alex