Database Users

After upgrare Stucked at boot screen

Artemis and PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap
i tried to upgrade my o2 arte200,i waited 30min. but installation frozen.
i did reset but after reset my phone stucked at bootscreen
IPL : 1.25.0001
SPL: 1.25.0000
GSM : 02.67.90
OS : 1.28.0.0
Please help... i tried hard reset and soft reset ... but no way...
when i plug usb cable activeSync dont recognise phone

same problem here,
help needed in advance

Active sync is usable only with Windows booted device. If Windows isn't able to boot, you must enter into bootloader, plug usb cable and then start rom flashing.

hi sir
i entered bootloader screen,connected usb cable ... (i can connect using mtty)
i run the software "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE"
but gets an error message " cant connect to the phone"
WHY ???

finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????

CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
is a Rom for the Wizard not for the Artemis.
You need the original ROM so you have to search for the O2 ARTE200 ROM. The language of the ROM has to be correct as well.

how do you get the phone into the bootloader?

Tha said:
how do you get the phone into the bootloader?
Click to expand...
Click to collapse
Press and hold the record button and then do a reset.

no it doesn't work
My DOPOD was in the same trouble. I got the same vender ID error. Does anyone know where to get the original DOPOD P800 chinese ROM?

The same problem has I also.
My ROM upgrade ended bad. Test of installing of different ( I have already them probably 12) the INVALID ends VENDOR ID
I it can not now to remove CID nor to find out what it has it CID HTC__001 does not it fit. T - MOB 005 does not it fit.
I look for original romu from Dngaard ( DK)
Someone knows what CID maybe it is in HTC 3300. I have HTC P3300 is distributed would to Dangaard.
Where from him download
I greet
Irek ( POLAND)

im having the same problem on the o2 orbit ( need a orignal rom

upgrading
hai i am stuck in o2 orbit flashing in bootloader mode
help needed urgent

i got it working after i found the original german rom...loaded the orbit into the bootloader screen with 3 colors....plugged in the usb cable..then ran the german rom, after a few mins it reset and the orbit loaded up...after that i followed these steps to get it into english
http://forum.xda-developers.com/showthread.php?t=290241
flashed it with the tmobileuk 1.13 shipped file. everything is ok now.

cbprod said:
i got it working after i found the original german rom....
Click to expand...
Click to collapse
Where do you find the orginal rom?
Please help us!

send me a pm with your email, i'll send it to you

got mine back from the repair center friday.
no cost at all, fixed

route said:
finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????
Click to expand...
Click to collapse
could you tell me how did you manage to conect your phone? i have the same problem and i can't get my palm recognized by windows...

you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).

xister said:
you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).
Click to expand...
Click to collapse
is that the o2 UK rom or the German one

asking about,use the power from the USB port to charge the XDA

help me to break & solve this problem, maybe can also help the other members..
I tried to upgrade my XDA to WM2003SE everything goes right,
bootloader first time i still use v5.22
but when I soft reboot it freezes on the OZUP screen and
message ONLY FOR MICROSOFT bla bla bla....
i get this ROM from http://www.romkitchen.de/ ==> WM2003SE
then downgrade bootloader from v5.22 to v5.15,
using MMC (flash SD) continue to special rom 1.2,
and then cooked again using PC2002 by my own creation based from
romkitchen, what i want to ask is :
i cannot connect again via dekstop activesyn if i want to change
my ROM because my cradle cannot detect my charger?? but if i charge
directly, its work. What is the problem?
is my cradle/dekstop broken at the charger socket?
so what i need to do? just change the wire or socket or
i use the step like at http://wiki.xda-developers.com/index.php?pagename=WallabyCradleMod
if i prefer use the 2nd method, is that really OK? so just used cradle/deskstop, no need
power charger again if i want to change ROM to WM2003SE, because only can use via activesync?
after i change bootloader to v5.15, keep trying to change but only can via Flash SD Card,
i change to WM 2003 final, still same problem....after finish, only screen cannot enter the
menu or else, only boot screen until i am waiting for 15 minutes??? then change again to
WM2003 but using from http://www.romkitchen.de/tools, still same again....boot screen again...
haiyaaaa.....what happen?? i dont know, tired, always overtime to do this,hehehhee...
all my friends, help me...need your advice ^_^V
*now, i still used ROM from PC 2002,cooked again using PC2002 by my own creation based from romkitchen.
bootloader v5.15
Microsoft Pocket PC --> PC2002
Version 3.0.12039 (Build 11178)
ROM version : 3.17.03 ENG
ROM date : 05/15/03
Radio version : 6.24.00
Protocol version : 324e4
Model No.: PW10A1

I can not really help you, but i was also in the same situation, that i have had a device, that doesn´t work with any other ROM than PPC2002
Flashed several WM2003 ans the WM2003SE but non of them worked.
So i rest at PPC2002
Stefan

ow ow...
auch.. ok, thanks for the comment, i give-up,hehehe..but only for now,
take a rest first but i dont know for t'mrow, actually from 10 flashed,
i got 1 success, can got WM2003SE but with almost empty battery,
i know the inside and already set all, including i notice bluetooth icon,hehehe..
but how? i wonder that my sx56 with fake bluetooth, only icon
but after i charge my sx56 then i soft reset, its gone, back again with only boot-screen, after that, i can't find again WM2003SE ROM only lock with boot-screen, and ONLY FOR MICROSOFT..blablabla...
and about for my cradle/dekstop? how is it? can u give me solution to fixed it??
btw,thanks for helping, tips & trick hehehe...
i will keep trying to find/solved this problem by my own way ^_^V

modify my cradle/dekstop success
its working, i try to modify my cradle/dekstop with that steps (look at the top this thread), and it's work...actually not me who did it, but my friend,hehehehe....i ask his help and he agrre to doit, but all the risk is still at me, now i can charge and also syncronized to my notebook

Active sync dont connect in bootloader mode

Hi, just bought a qtek 2020i, i am trying to upgrade it to wm6.1 but no mather rom i use, it always get me error 112 witch says ce erase error in log file.
after searching and searching i only find one guy that solved this problem using a computer with windows me and activesync 3.7 without antivirus or firewall.
my quetion is:
to upgrade a 2020i's rom, activesync has to connect to pda in bootloader mode?

OCRAM00 said:
Hi, just bought a qtek 2020i, i am trying to upgrade it to wm6.1 but no mather rom i use, it always get me error 112 witch says ce erase error in log file.
after searching and searching i only find one guy that solved this problem using a computer with windows me and activesync 3.7 without antivirus or firewall.
my quetion is:
to upgrade a 2020i's rom, activesync has to connect to pda in bootloader mode?
Click to expand...
Click to collapse
First off, update your Activesync to 4.5. Activesync shouldn't "connect" when in bootloader mode, however you can flash ROMs if you're device is connected in bootloader mode. You can also run the RUU after installing the modified SPLs needed.

Ignoring the first issue of connection, you can't actually achieve your stated aim of upgrading an Alpine to WM6 anyway, no such ROM exists.

hi, i've found and download a rom of wm6.1 to alpine 2020i and also a wm6.5.
I've tried with the activesync 4.5 and still the same error, i dont understand why it wont erase the rom to install new one

i like to see this rom give mi link or info wher to find it. i well try to instal yt on my xda IIi

be2nzs
hi guys, i have problem to upgrade my alphine, i just want wm 6.5 runing on my device, can anybody help me ? i am sorry for my english.

3 colors at boot but that all

Hi,
I can install few rom :
- Prophet_ShadoW_2.0_CE
- Prophet_ShadoW_1.0
- PROPHET_DIAMOND_WM61_20226_SB
- RUU_Prophet_220734_2207114_024721_QtekWWE_Ship
It's install at 100% but my s200 stay 3 colors at boot.
My fone is dead ? Or i forgot anything ?
Thank.

Try to install the original rom of qtek s200 ( use wiki htc) , and them do a Hard spl if the phone still in BL mode.

3 clour boot screen
Download aku 2.2 for 3g if your phone is 3g
disable the usb connectivity in active sync
then run the aku programme connecting the usb cable
then your phone should be OK

try flashing the NVID rom,it fixes problems, here is the link
http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs

[Q] Please help me solve my pda problem (qtek 9100)

format failed
g4
IPL 2.17.0001
SPL 1.01
i always use windows mobile 5, it happened when i want upgrade rom. only one rom (rom update utility 2.00.3) works when upgrade, but after restart pda the problem return.
qtek 9100