Qtek 1010 stuck at boot screen - MDA, XDA, 1010 Software Upgrading

I am sorry, this has probably been covered before but I have search but can't find it at the moment, my Qtek 1010 is stuck at the boot up screen where it shows Qtek.
I have upgraded the rom using the SD Card and still you reset the phone and it just sits at the first screen with the Radio and rom versions at the bottom of the screen......
Please help.
Thanks

Went flashing process fine? Checksum OK?
Had you done the hard reset?
Have you tried reflashing it again?
Stefan

I reloaded Rom from SD card and reset with the stylus in the little hole in the bottom and same problem, it can't get past the boot screen.

Sorry all, I installed the original rom and everything is fine now.
Thanks for your help, this is the greatest site.

seal said:
I reloaded Rom from SD card and reset with the stylus in the little hole in the bottom and same problem, it can't get past the boot screen.
Click to expand...
Click to collapse
Just short question?
Which little hole? There are two.
One on the side where the earphone connector ias, and one on the other side....
Stefan

Hi LumpiStefan,
I was making a mistake and yes not reseting the phone with the little hole, I have an XDA Mini and I forgot all about the other little hole that you unwind the stylus for.
Only problem is it doesn't fix it, The only rom I can get to work on it is the HTC Qtek v3.18.04wwe, it is the only rom that will boot into the operating system, I have tried other roms from this site but none of them will boot, I did get the 2003se rom to work but the phone part didn't work, it was like there was no radio, there was no signal graph up the top, so I tried to install the 2003se rom over the top of the working Qtek rom and same problem, it can't boot.
I really want 2003 on the phone so I can put Voice command on it.
Any help would be great. Thanks

I have downloaded nearly every rom and no 2003 rom will work, they all just after I hardreset it want go past the boot screen. So I load the old Qtek rom back on every time by SD Card and everytime it boots up fine, I don't understand, why does the Qtek rom work but no other.......
Any help please...Please...

Related

QTEK Death ?

I have made an upgrade from wm2003 4.00.01 and radio version 3.14 and i'v cook a rom at kitchen.romanweb.com, i'v chosen the 4.00.16 ENG T-Mobile US, but at the end of the upgrade via usb cradle, when i reset the phone e doesnt apear anything, than i press on/off button an reset and apeard the wallaby bootloader v5.15 with gsm ok.
I didn't know at the time what it was, then i come here, i'v made a sd card flash with XDArit then upload with checksum ok, and once again when reset, the same, the wallaby boot loader.
I'v just entered the NK.nb1. I'v tried diferente roms. is it death ?
ps. i hate to say this but, i dont have a backup of my old rom
Help-me Please ................[/b]
How are you resetting the xda, you need to disconnect the battery for one minute, you do this by unscrewing the stylus and using the top half to poke the hole in the lower right of your xda, after one minute poke once more, do this after using the sd card flashing method.

HELP: No Bootloader after BigStorage Flash

hello guys, i'm really desperate now. my Magician is dead. i followed the laid out procedure 100% for upgrading to bigstorage. that's what i did:
- dump rom on to the sd card (512MB).
- got a external card reader (since the one in my laptop did not work with ntrw.exe)
- killed ActiveSync (wcesmgr)
- dumped the rom to my hard disk
- got Big_ROM_Ger_1.11.nb1 from ftp
- changed the first 416 bytes with ultraedit.
- wrote the resulting rom to the sd card with ntrw.exe.
- flashed (got the question in bootloader mode, pressed power).
- flash completed, got the 100% message and checksum failure.
- did a softreset
- my Magician is now DEAD !!!
Tried to put it in bootloader mode again, nothing! Put out the battery, unplugged and replugged usb cable, nothing!
PLEASE, any suggestions or help ??????
Please explain "nothing." Are you getting anything on the screen, blank screen, backlit, logo, text, anything?
Can you zip and upload your modified ROM dump file to dropload, rapidshare, or some other portal where someone can take a look?
Did you pull the battery completely, reinsert it, and pressed the reset+camera+power to get back into the bootloader?
BeyondtheTech said:
Please explain "nothing." Are you getting anything on the screen, blank screen, backlit, logo, text, anything?
Can you zip and upload your modified ROM dump file to dropload, rapidshare, or some other portal where someone can take a look?
Did you pull the battery completely, reinsert it, and pressed the reset+camera+power to get back into the bootloader?
Click to expand...
Click to collapse
the screen is absolutely blank. if i plug in the power cord not even the charging lamp is on.
i removed the battery completely for a few hours now, reinserted it just that moment and pressed reset + camera + power --> blank screen, no backlit, no logo, no text. i even used my torch to make sure i didn't miss the bootloader message. nothing.
when i press the reset + camera + power button the blue led blinks for a split second but then again nothing.
tried it with and without external power....
any clue????
rom i used
BeyondtheTech said:
Please explain "nothing." Are you getting anything on the screen, blank screen, backlit, logo, text, anything?
Can you zip and upload your modified ROM dump file to dropload, rapidshare, or some other portal where someone can take a look?
Did you pull the battery completely, reinsert it, and pressed the reset+camera+power to get back into the bootloader?
Click to expand...
Click to collapse
you can finded the zipped rom i flashed here:
http://62.218.22.81/MagicianRom/[/url]
Sounds like you have screwed it completely. Back to the shop...
saldous said:
Sounds like you have screwed it completely. Back to the shop...
Click to expand...
Click to collapse
well, could be possible.... kinda teaches me not to mess around too much. i flashed my old xda II with magneto and all, never had any problems....
anyway, i will try to clear the backup battery over night and try it again tomorrow. if it still doesn't work, i'll get it back to the shop. it's brand new (2 weeks), so i guess (hope) it shouldn't be a problem.
No solution - but I had the same problem
Hello,
sounds that you have exactly the same problem I had. I also wanted to use bigstorage. First I updated to 1.06 official rom from T-mobile Germany. Then I used mksbigstorage to modify this rom. After installing this my mda was stuck at the splashscreen. But the bootloader still worked so I was able to restore my original rom.
Next I downloaded the 1.11 extended german rom from xda-developers ftp-server. I also replaced the first 416 bytes with the one from my rom. After installing this rom and doing a softreset my device was completely dead. No bootloader, no even a blinking light when connecting it with the power supply. I also tried to remove the battery for some time. But nothing worked. As I also had this device for just some days I finally did send it back and recieved a new one.
On this new one I also tried to modify rom 1.06 with mksbigstorage. But after that it was again stuck at the splash-screen. Mksbigstore seems not to work on this rom. Finally I was able to use bigstore by modifying two adresses in the original 1.06 rom downloaded from my device. This method is described in this forum. Worked without problems.
So I do not know what went wrong and I am sure I followed the instructions for flashing bigrom exactly, but as I am not the only one with this problem there is a risk flashing under certain circumstances.
7bft said:
saldous said:
Sounds like you have screwed it completely. Back to the shop...
Click to expand...
Click to collapse
well, could be possible.... kinda teaches me not to mess around too much. i flashed my old xda II with magneto and all, never had any problems....
anyway, i will try to clear the backup battery over night and try it again tomorrow. if it still doesn't work, i'll get it back to the shop. it's brand new (2 weeks), so i guess (hope) it shouldn't be a problem.
Click to expand...
Click to collapse
I had the same problem flashed XDA 1 hundreds of times without problem. Flashed Magician device one time --> same problem as you have.
I've sent my device to repair center and they installed a new motherboard. So i don't believe that tehre is any fix to relive you're device..... :-(
Stefan
I don't see anything wrong with the ROM file except for the fact that it's slightly larger than my ROM (65281k vs. 65427k). May have been a bad write to the SD card. Was your card a 64MB SD card?
BeyondtheTech said:
I don't see anything wrong with the ROM file except for the fact that it's slightly larger than my ROM (65281k vs. 65427k). May have been a bad write to the SD card. Was your card a 64MB SD card?
Click to expand...
Click to collapse
My card was a 512 MB SD Card, since it is the only one I have.
On Monday I'll send it to the service center
Re: No solution - but I had the same problem
beta2morita said:
Hello,
.... I also tried to remove the battery for some time. But nothing worked. As I also had this device for just some days I finally did send it back and recieved a new one.
On this new one I also tried to modify rom 1.06 with mksbigstorage. But after that it was again stuck at the splash-screen. Mksbigstore seems not to work on this rom. Finally I was able to use bigstore by modifying two adresses in the original 1.06 rom downloaded from my device. This method is described in this forum. Worked without problems.
...
Click to expand...
Click to collapse
Thanks for your response, kinda reduces my pain and asures me that I'm not a complete idiot....
I'm now pretty sure that I have the same problem as you have and that sending it to the service center is my only option....
At least I can use my Himalya with Magneto a few more days :wink:
I guess I will not try this again since I don't want to risk killing it again, allthough I allready had problems with the storage size on the working device (tomtom).
One more question: Did anybody ever had problems on upgrading from a t-mobile rom to a vodafone rom? is it even worth upgrading to 1.12?
Thanks for your help guys!!!

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

my i-mate jasjar is dead

hi all,
my jasjar had an error while upgrading to ranju 7.7,
i tried to reset, didn't came back,
hard reset neither,
i went to bootloader mode, i could,
i connected it again to the pc, it showed usb,
i tried to flash to Rom that was working previously it arrives to 7% than stops,
what should i do ...
i tried to flash with official rom, it says that the rom wasn't designed for this model, it has worked before...
please help...
Hi,
if you search in the ranju's thread there's the solution.
You could have the doc corrupted. Simply read the wiki,
you must use mtty to format your device and then reflash the rom you want (with radio rom also).
Had similar problem
upgrading Imate JasJar to Ranju 7.7, only at first it showed as success, then it started behaving funny during customization, then failed to customize, then got stuck on Windows 6.1 green flash screen and eventually refused to budge beyond blue Imate screen with versions info. I tried everything, a few dozens of hard resets returned me to the same problem, removing the battery didn't do much and mtty didn't show USB as available option, so couldn't even use that. I was pretty much stuck solidly and for a while. At my wits end I read that problems like mine are associated with DOC corruption and my JasJar is as good as dead, quite a few people suggested to those who are in the same position to throw their bricked babies away, as there is no economic solution apart from sending it for service where the corrupted chip may be replaced. What do you know, I followed wiki recommendation and entered a boot screen by pressing light power reset, then just flashed back to Ranju 7.6 and my JasJar was brought back to life!!! The update went without a glitch and everything is working fine. I guess I will keep the 7.7 on my O2 and 7.6 on my Imate for now, won't be risking an update anymore on the JasJar, don't think I have much hair left after all the pulling I did trying to bring it back to life. Hope this helps someone in the same predicament
jokove said:
hi all,
my jasjar had an error while upgrading to ranju 7.7,
i tried to reset, didn't came back,
hard reset neither,
i went to bootloader mode, i could,
i connected it again to the pc, it showed usb,
i tried to flash to Rom that was working previously it arrives to 7% than stops,
what should i do ...
i tried to flash with official rom, it says that the rom wasn't designed for this model, it has worked before...
please help...
Click to expand...
Click to collapse
does it turn on at all?
Does the device turn on at all after a hard reset?
Dude, I had a same problem it rectified though, check following of my blog...
http://jay-joshi.spaces.live.com/blog/cns!851D717EDFF14CEC!3258.entry
or
http://buzzdev.net/read.php?40,13307,page=1
Rarest_Kind said:
Dude, I had a same problem it rectified though, check following of my blog...
http://jay-joshi.spaces.live.com/blog/cns!851D717EDFF14CEC!3258.entry
or
http://buzzdev.net/read.php?40,13307,page=1
Click to expand...
Click to collapse
Problem resolved?

Help! HTC Hermes won't boot up properly

Hi
I've got a HTC Hermes that won't boot up properly.
I've had a quick search and can't find to find the exact same proble but apologies if this has already been raised.
I previously flashed my T-mobile ROM with RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar.
The problem started when I downloaded a Registry Optimizer from Windows Update. When I started using this my phone was not in airplane mode, and just hangs on the logo screen (this is the gold Tai Edition)
I tried to do a hard reset (this goes to the screen with the four colour bands on it), and then when I reset it again it just switches to the logo screen and stays there. After a while, the screen goes white and stays there
I've got only a basic knowledge of flashing ROMs and when I first flashed my ROM i used Hard SPL and the basic AT&T Windows 6.1 ROM, before using TAI's custom one.
I presume I need to try and re-install the ROM (via the SD card, as Active Sync doesn't recognise the phone)
I was aware of risks whilst using the Registry Optimizer and realise that this is my fault, so I'm not expecting any quick fixes
Would be grateful though if anyone could point me in the right direction, if my phone is recoverable, and not bricked.
Cheers
You flashed a rom for the Kaiser.... You have a Hermes...
Looks like a brick to me....
If you use the sd card method you might be able to fix BUT make sure its a Hermes rom....
Thanks for pointing that out!
I found the thread on how to unbrick a hermes, so should be ok from here..

Categories

Resources