hi all, i've the widcomm driver in my xda2, and them runs smoothly
but.. i've the need to share gprs connection from xda2 to my laptop... i can't for 2 different motives:
1) if i enable widcomm drivers, i try to launch the dial-up service... he connects to the standard GPRS provider... and 99% of time it resolves the hostnames... but can't download or ping them :roll:
2) if i enable the microsoft driver (deactivating widcomm, activating microsoft... and turning up the wireless modem software), i can't find the service for let me be connected. (i only see "voice gateway" bluetooth service )
before i installed the widcomm drivers, with this settings i can succesfully connect to GPRS & share connection over bluetooth.. the widcomm are probably the trouble :?
someone know a clear way for make it run smooth ?
Related
pleeze someone help...ive read all the posts, but still can achieve this. I Have the widcomm stack on xda11, and widcom on xp. i hase a broadband connection, which is called realtek adaptor in my connections. bluetooth is working, ie file sharing is ok, and when i click to connect the network it looks good, but its not really connected. i think i have to create a network bridge on xp, which ive tried, or enabled internet network sharing, which keeos coming back with an error
any help will be gratefullyreceived, and may be repayed with guinness!
Hey everyone,
Okay I'm going to try and explain what I am trying to do here, but I'm sure I'll miss some steps. I think I know what the problem is, but I still can't figure out a way to resolve it.
I have a Sony Ericsson Z710I mobile phone. I also have an i-mate Jasjar running AKU 3.2 (JW's Rom). Here is what I am attempting to achieve.
I want to use the Z710I as my telephone. I have bluetooth turned on and have connected the Jasjar to it. On the Z710I I have enabled the "bluetooth internet" option and set it to connect to the proper APN. On the Jasjar I have created a new network connection that uses Bluetooth modem, and have put in the APN as *99#.
So when I connect the Jasjar to the internet, it dials the bluetooth on the Z710. It recongnises the *99# command and connects to the proper APN and connection. This is the point in where it just doesn't want to hitch up. The phone has full access to the internet, however ... the Jasjar is just grabbing data traffic and I'm not sure why. It reports connected and is communicating to my knowlege.
When I disconnect the Z710 from the internet, the Jasjar immediatley reports that the modem has disconnected. That why I figure there is communication.
I have tried (on the Jasjar) to edit the network card settings for the bluetooth adapter to 'obtain IP automatically' but it made no difference.
Does anyone have any ideas ( or questions for me to help clairify?)
Thanks
Nathan
What kind of communication did you try? Internet Epxlorer? Opera? Messaging?
For example, IE, which is based on the Connectivity Framework, has a lot of problems that may render a connection non-working - I've written several articles on this stuff. A solution is trying with,say, OpMob / Messaging to be absolutely sure it's not just an IE-related problem.
Menneisyys said:
What kind of communication did you try? Internet Epxlorer? Opera? Messaging?
For example, IE, which is based on the Connectivity Framework, has a lot of problems that may render a connection non-working - I've written several articles on this stuff. A solution is trying with,say, OpMob / Messaging to be absolutely sure it's not just an IE-related problem.
Click to expand...
Click to collapse
I tried using activesync as well as IE, google maps and other internet based connections.
I just tried it right now, dialed the connection and tried to activesync. The z710i connected at the Jasjar's request and the Jasjar said connected. It then just sat there "synchronizing folders"
There are two APNs available through my phone. One is for WAP traffic, the other for Internet bound traffic. My phone is connecting properly or it at least setup properly to route traffic over bluetooth to the internet one.
I did hook up the phone through a bluetooth adapter on my computer and used it as a wireless modem it did work there. I wonder if the problem is the Microsoft BT Stack (it doesn't have a PAN profile).
Do we have a way to uninstall the MS BT Stack and install the WIdcomm one which would support PAN?
Just a thought.
Thanks
Nathan
lirathal said:
Do we have a way to uninstall the MS BT Stack and install the WIdcomm one which would support PAN?
Click to expand...
Click to collapse
Are you sure the z710i would support PAN server? I don't think so.
If it does, then, check out the Hermes / Wizard Widocmm BT stack hacking-related threads; hope the stack can also be hacked onto the Universal too.
(Unfortunately, AKU3 with its new BT approach (see my related articles if interested) won't work because it only supports BT PAN server mode for dial-up purposes, not client mode.)
Menneisyys said:
Are you sure the z710i would support PAN server? I don't think so.
If it does, then, check out the Hermes / Wizard Widocmm BT stack hacking-related threads; hope the stack can also be hacked onto the Universal too.
(Unfortunately, AKU3 with its new BT approach (see my related articles if interested) won't work because it only supports BT PAN server mode for dial-up purposes, not client mode.)
Click to expand...
Click to collapse
I'm not sure how to check if it supports Bluetooth PAN server. I know that the Z710I can be used as a Bluetooth Modem (as I said previous, I hooked it up to my computer and used it as a internet connection - but when I did that I had to enable PAN client support on the PC [i think]) .. So is this where we are inherantly are having the problem? The Jasjar doesn't support PAN Client therefore, when it connects it doesn't know what to do with the connection?
I have figured it out.
I connected my Z710I to my laptop and I examined the "dial-up" connection and the syntax for the connection number was *99***2#
I changed the connection on my Jasjar, connected and everything is wicked. Now I can still sync my Jasjar while using a regular phone for a while.
Talk about a Personal Area Network .
Thanks for all the help.
Hi all,
I've seen a lot of threads specifying how one would go about using the bluetooth to share the phone's internet connection. However, I would like to do the opposite, that is, share the PC's internet connection via bluetooth so that I can surf the net on my phone (I do not have wifi). Any help would be most appreciated.
http://forum.xda-developers.com/showthread.php?t=274581&highlight=bluetooth+modem
http://forum.xda-developers.com/showthread.php?t=313886&highlight=bluetooth+modem
many more hits of you use search and search "bluetooth AND modem"
thanks for the reply, but i already know how to do this. Perhaps you didn't understand my question; I do not want to use my XDA as a bluetooth modem. I would like to use my home ADSL connection via bluetooth to access the internet through my phone. This feature was there by default in my SE P910i, and I'm sure it should be possible to do this via my XDA as well. Once again, I do NOT want to use my XDA as a bluetooth modem
when connected to activesync pda's have the same network access as the pc they are connected to unless one have disabled it
so synch with bluetooth to your pc and you got it's internet
Check this page. Hope it helps you
http://www.geekzone.co.nz/content.asp?ContentId=449
I'm successfully running such a setup, using Linux (w/ bluez stack) on the Internet Gateway. However, I had only luck with the Widcomm stack on the Windows Mobile, w/ the MS stack, I could not manage to find any way to use DUN or NAP. With Widcomm, you can configure access via a "Bluetooth Access Point", which will use DUN services on the Host (Gateway) computer. On Linux, this means setting up dund (comes with bluez) and configuring a PPP profile for it.
Any idea if Widcomm BT stack is available for installing it on WM5. I think mine is with MS by default and couldnt find an option to configure it.
I think it isn't offered for free to the public. Nevertheless, there seem to be a few CABs with the broadcom/widcomm stack out there in the WWW. Google might lead you the way...
Thanks a lot for the feedback guys.
I have succesully used DUN with both my original iMate Jamin ROM and PDAViet 4.0.0.0.6 ROM to access the internet via a linux box running Bluez and dund.
I was hoping the new PAN profile in wm6 would allow me to simplify and setup a standard wm6 PANU -> linux NAP. However it looks like wm6 only supports running as a NAP and wont allow you to do that unless your connected to the internet via GRPS etc.
Is it possible to either add support for PANU in wm6 or activate the NAP without an active connection?
Is there any way to enable dialup network in wm6 without installing other BT stack?
Now i can connect only PAN service
You dont need DUN , there's a thing called internet sharing. check it out
Well, it's ok.
Now i can't connect my ActiveSync via BlueTooth properly.
I have message: "Cannot find an existing Bluetooth partnership with PC that supports ActiveSync" but partnership is there. Any ideas?
it's working properly. thanks a lot
I've tried most of the solutions/methods on this forum/net, but it just doesn't work!
I'm able to pair the device, start the PAN service and 'Intetnet Sharing' gets connected as well, PC gets an IP address, but I get no response when I ping or open a webpage.
On the phone end, I've tried with WM5, WM6, WM6.1 and even with WMWi iRouter. On the PC end, tried with 3 different XP/2003/Vista machines. I'm using BlueSoleil 6.2, but had no success with older or later versions either.
Internet Sharing over USB worked fine till my USB connector broke so BlueTooth/WiFi is my only option.
Can soneone help me out please?
if you want to teeth your gprs connection so your pc get internet that way
PAN is not the way to go
search for bluetooth AND modem
in the forums there are many guides how
it's setup
PAN is if you want your pda to get internet from your pc
Thanks for the reply. I tried Bluetooth DUN but it's too slow (115kbps) and keeps getting disconnected every 5 mins...
If Bluetooth PAN is for sharing PC net only, why then does it show up under 'Internet Sharing', and also shows the Cellular net option, as if it can connect the both, like it does for USB? If PAN isn't meant for sharing cell net, it shouldn't show the option, right?
I mean, it's not *impossible* right? We have a TCP/IP network established with all IPs properly assigned; only one device has net access; how hard or improbable can it be to share the net? There has to be a way! :|
Infact, even the inbuilt Help on Internet Sharing describes that cell net can be shared w/ the PC over bluetooth using 'Internet Sharing' and says nothing about connecting as a modem and the whole *99# thing. I was of the opinion that 'Internet Sharing' made that method obsolete...
- Disconnect everything
- Open internet sharing, select Bluetooth PAN, connect. IS should tell you "waiting for bluetooth connection".
- On the PC, connect to the PAN service on the phone. This must work, I've used it countless times.
If traffic doesn't go through, you probably have a proxy set on your device (happens with some network operators) that you need to disable for it to work.
^ That's exactly how I've been trying .. maybe it's because of BlueSoleil?
Which bluetooth stack are you using? I've been searching the local stores for a non-bluesoleil adapter but no luck so far
I'm using the Widcomm stack that came with my BT keyboard/mouse set. I think you can download it for free anyway...
kilrah said:
- Disconnect everything
- Open internet sharing, select Bluetooth PAN, connect. IS should tell you "waiting for bluetooth connection".
- On the PC, connect to the PAN service on the phone. This must work, I've used it countless times.
If traffic doesn't go through, you probably have a proxy set on your device (happens with some network operators) that you need to disable for it to work.
Click to expand...
Click to collapse
Hi Kilrah, could u provide some details about how to disable proxy on the device .
I can connect but no internet traffic on my laptop .I am using vodafone live gprs on xda orbit .Thanks