Is there any way to enable dialup network in wm6 without installing other BT stack?
Now i can connect only PAN service
You dont need DUN , there's a thing called internet sharing. check it out
Well, it's ok.
Now i can't connect my ActiveSync via BlueTooth properly.
I have message: "Cannot find an existing Bluetooth partnership with PC that supports ActiveSync" but partnership is there. Any ideas?
it's working properly. thanks a lot
Related
hi all, i've the widcomm driver in my xda2, and them runs smoothly
but.. i've the need to share gprs connection from xda2 to my laptop... i can't for 2 different motives:
1) if i enable widcomm drivers, i try to launch the dial-up service... he connects to the standard GPRS provider... and 99% of time it resolves the hostnames... but can't download or ping them :roll:
2) if i enable the microsoft driver (deactivating widcomm, activating microsoft... and turning up the wireless modem software), i can't find the service for let me be connected. (i only see "voice gateway" bluetooth service )
before i installed the widcomm drivers, with this settings i can succesfully connect to GPRS & share connection over bluetooth.. the widcomm are probably the trouble :?
someone know a clear way for make it run smooth ?
I am trying to configure my XDA2 to connect to my PC and surf the internet via a BT connection. I can Sync via BT but when I try to set up my connection it keeps asking for a phone number despite me saying it is over a Bluetooth connection and my IP is broadband. Sorry if this has been asked but I did search for any info on this.
thomo said:
I am trying to configure my XDA2 to connect to my PC and surf the internet via a BT connection. I can Sync via BT but when I try to set up my connection it keeps asking for a phone number despite me saying it is over a Bluetooth connection and my IP is broadband. Sorry if this has been asked but I did search for any info on this.
Click to expand...
Click to collapse
Why do you need to setup connection for since it's already connected with ActiveSync via BT? Basically once you get connection between your device & activeSync, that's all the step you did. Unless a firewall has stopped your device from accessing to the internet; if it's the case, create exception for your activeSync, and retry browsing with your device.
hope this helps.
regards.
thanks for yor reply, Each time I try to connect the the interneet on my device it keeps trying to connect via GPRS and not through my PC via BT....
Go to ActiveSync, open the options menu & go to Rules tab.
At the bottom, you will find Pass Through Conenction, make sure its set to The Internet and not Work
Cheeeers 8)
thats it, it finally works. Thanks very much.
Glad to hear that, thomo
You're welcome anytime, dude :wink:
activesync through bt
go to setup in bluetooth and select the activesync in bt
pair the pda or ppc
give password
in wm2005 select activesync through the bt
brouse internet
i did myself
I'm having a similar problem and have effected the setting as above, however IE on my IIs says "the page you are looking for cannot be found". My computer connects fine and I have the same issue when trying to connect the device via WiLan, although I do connect to the network.
I've been trying to fiddle with the settings for a few days now but no success...anyone out there got any ideas.
Many thanks
I have mastered it now, I sync using BT on my device, leave it connetced, close Active sync on my XDA 11, Click on IE and the device connects through my PC, super duper.........
Thanks, this is what i am looking for now. I will try it
i can now only online with cable, not through Bluetooth connection
go into the advantage settings for connections
there you should be able to change the network back to my isp insted
of my network
bluetooth-internet
Hai...iam new here..i have got O2mini and would like to connect to internet via bluetooth...
i try using usb cable and activesync program to serve internet and its working.
...i succesfully connect my pc and ppc via bluetooth by using ppc activesync but when try connet to internet its still go to gprs..
pls help me...TQ
like i said again and again in this thread it's all about which network is picked in advantage settings under network connections in systems
I also tried to make a connection to the internet with activesync and usb. But with my mda doesn't work. iexplorer says the page you are looking for cannot be found. But my ppc says "connectivity the internet Pc connection". What are the settings on your ppc, so i can check?
Somebody help me.
test with ping
and maybe messenger to see if it's a dns issue
and if people use pocketplus they prob should make sure that it's not set to close insted of minimizing otherwise the connection would most likely be closed when they close activesync
Thank you very much. You solved my problem.
ezzkht said:
Go to ActiveSync, open the options menu & go to Rules tab.
At the bottom, you will find Pass Through Conenction, make sure its set to The Internet and not Work
Cheeeers 8)
Click to expand...
Click to collapse
I tried to use Trinity as a modem and did not manage to make this work.
I connect the usb cable. Start ISharing program on pda. Click conect. Says connected. 3G connection works. However the laptop is not connected to the internet.
Bluetooth also does not work. I can't find a way to create a PAN as they call it.
I would appreciate any suggestions as the manual is not clear on this topic
edit: i start internet sharing on my pda. i choose bluetooth. click connect. it says: Device setup finished. On the PC connect Bluetooth PAN.
On the PC i find my device. Find available services. Double click on 'Network Acces Point on Trinity'. I get a message that the computer is connecting and then an error: The Network Access connection failed: Could not connect to the remote device'
edit2: finally solved it.
I had to enter advanced bluetooth config on laptop. Under 'network access' properties I selected 'allow other devices to create a private network with this device'. Now it works.
hi,
i had the same issue, using bluetooth, but it´s the same, i guess.
you need to connect the pda with the pc, and when you get the connection, you go to the program menu in the pda, and select in the submenu connetions usb/bluettoth pan and connect.
the dial up connectiosn should start.
tell me if suceed.
i start internet sharing on phone. then go on bluetooth->quick connect-> network access -> my phone name. then it works as i mentioned above. but i had to change some properties in my bluetooth configuration to make it work.
The same for me : when I try tu use it as a GPRS modem for my TomTom Rider device, the Rider says that the DUN profile isn't provided as a service by the Trinity !!! Use to work perfectly with my old Magician !!! I'm really disappointed ! Will see if the brand new ROM with GPS feature corrects this...
try to start internet sharing first (in trinity), connect to gprs and then start bluetooth services discovery on tomtom.
I'm not using bluetooth, but trying to use the phone as a modem using USB with a laptop. It works, but is really flaky, so would appreciate some pointers on how to fix the problem.
First thing that I do is connect the phone to my laptop via USB. Activesync starts up on both the laptop and the phone. Then, when I start the Internet Sharing program, the phone stops Activesync and connects to the network. Everything works fine for a while and I am able to surf the net on both the Trinity and the laptop with no problems for a while. The problem is that after a period that can vary from 10 minutes to 1 hours, the laptop loses the internet connection. The phone is still connected to the internet though and I can still surf using the PDA. It's just the laptop that loses the connection.
I have to reboot the laptop and soft reset the Trinity to repeat the process to get internet on the laptop going again.
Any ideas what's causing the problem? I've tried disabling Advanced USB Functionality on the Trinity, but the problem is still there...
I've tried most of the solutions/methods on this forum/net, but it just doesn't work!
I'm able to pair the device, start the PAN service and 'Intetnet Sharing' gets connected as well, PC gets an IP address, but I get no response when I ping or open a webpage.
On the phone end, I've tried with WM5, WM6, WM6.1 and even with WMWi iRouter. On the PC end, tried with 3 different XP/2003/Vista machines. I'm using BlueSoleil 6.2, but had no success with older or later versions either.
Internet Sharing over USB worked fine till my USB connector broke so BlueTooth/WiFi is my only option.
Can soneone help me out please?
if you want to teeth your gprs connection so your pc get internet that way
PAN is not the way to go
search for bluetooth AND modem
in the forums there are many guides how
it's setup
PAN is if you want your pda to get internet from your pc
Thanks for the reply. I tried Bluetooth DUN but it's too slow (115kbps) and keeps getting disconnected every 5 mins...
If Bluetooth PAN is for sharing PC net only, why then does it show up under 'Internet Sharing', and also shows the Cellular net option, as if it can connect the both, like it does for USB? If PAN isn't meant for sharing cell net, it shouldn't show the option, right?
I mean, it's not *impossible* right? We have a TCP/IP network established with all IPs properly assigned; only one device has net access; how hard or improbable can it be to share the net? There has to be a way! :|
Infact, even the inbuilt Help on Internet Sharing describes that cell net can be shared w/ the PC over bluetooth using 'Internet Sharing' and says nothing about connecting as a modem and the whole *99# thing. I was of the opinion that 'Internet Sharing' made that method obsolete...
- Disconnect everything
- Open internet sharing, select Bluetooth PAN, connect. IS should tell you "waiting for bluetooth connection".
- On the PC, connect to the PAN service on the phone. This must work, I've used it countless times.
If traffic doesn't go through, you probably have a proxy set on your device (happens with some network operators) that you need to disable for it to work.
^ That's exactly how I've been trying .. maybe it's because of BlueSoleil?
Which bluetooth stack are you using? I've been searching the local stores for a non-bluesoleil adapter but no luck so far
I'm using the Widcomm stack that came with my BT keyboard/mouse set. I think you can download it for free anyway...
kilrah said:
- Disconnect everything
- Open internet sharing, select Bluetooth PAN, connect. IS should tell you "waiting for bluetooth connection".
- On the PC, connect to the PAN service on the phone. This must work, I've used it countless times.
If traffic doesn't go through, you probably have a proxy set on your device (happens with some network operators) that you need to disable for it to work.
Click to expand...
Click to collapse
Hi Kilrah, could u provide some details about how to disable proxy on the device .
I can connect but no internet traffic on my laptop .I am using vodafone live gprs on xda orbit .Thanks
If anybody had managed to access the internet via Bluetooth PAN (via a PC ora BT accees point), then please provide explanation how to configure both: a PC with Boradcom stack and the HTC HD (which connection to use, how to use the Internet Connect Sharing on the HD, which IP addresses should be entered for the PAN network card etc.)
Your help is really needed
Thanks
I am sure this was answered the other day, do a search within the Blackstone forums.
Found it :
http://forum.xda-developers.com/showthread.php?t=470206
Yes, you are right. The opther thread title was about NULL MODEM, and could have been not clear. Due to the lack of help there, I did post this new thread with a more accurate title.
The problem remains the same. I still cannot access the internet via PAN. I can use BT ActiveSync to access the Internet , but this is not the right way.
Please, anyone who had succeeded, do post the steps to achieve BT via PAN
Thanks
Thats a really basic question. (your really did not find a answer on this forum?).
On ppc goto Programs/internetconnection/ and under connection choose bluetooth instead of usb. Than click connect.
On PC right click on bluetooth icon, chooce quickconnect to Network accesspoint.
Thats it. Of course you firs must pair device and set it to be"visible".
Thanks
I allready did that, I chose 'Network Access', under the Quick Connect, my PPC was detected, when I click on 'Connect' I get the message "Error creating 'Network Access Point' connection with device ,my device>" on my PC. This happens when I choose Serilal Port or Dial Up Networking too.
What am I missing?
Thanks
S u c c e s s
Thanks to you all foryour support.
The problem was with the BT stcak on my computer. I unistalled the Widcomm BT application and reinstalled it again. Suddenly, no more error messages. All is working ok.
Even I wanted to connect to my LAN internet connection on desktop over Bluetooth.
1. I have enabled BT on HD - Visible mode (No Bluetooth icon on Taskbar -- Why???.
2. Paired with Desktop - passkey exchange - Success.
3. Service Discovery - Two services found on THD:
a) Bluetooth PAN.
b) Bluetooth Dial-up networking.
(Please note - Object Push Service and FTP services are not there!!)
Anyway - Now if I try to Click Connect to the PAN:
"Establishing a Connection with ABX's Bluetooth PAN
..
Operation - Not successful. Please try it again..
I have soft reset HD and also reinstalled Bluesoleil on desktop several times.
Nothing seems to help.
As a side note
1.Even sending an object from Desktop is not possible as the Object Push Service is not visible..
2.Sending a text from a cellphone also fails - "Bluetooth Connection Failed"
I have "Obex inbox" installed if that information helps.. But the problem is there even before installing any app.
Is it that I got a stone instead of a "BlackStone" ??
Any help greatly appreciated.
Edit: Connecting Activesync over bluetooth worked. still unable over either ActiveSync-USB OR to do BT without Activesync
Any Ideas??