Hello There,
I've spend my free Sunday on flashing my ROM :roll:
I wanted to warn about a "bug" in the t-mobile 4.01.16 ROM with o2 radio 4.21. Here’s what happened:
I've upgraded from AT&T a.30.09 ROM with o2 Radio 4.08 to t-mobile 4.01.16 ROM with o2 radio 4.21.
- 1st I've installed the t-mobile ROM (SD Flash method Note: ALWAYS DO
THIS!)
- 2nd I've turned off my phone and installed o2 radio 4.21 (through
programB)
Problem:
Every thing went well and there were no errors at all! But:
When I tried to start my phone again there was NO SERVICE possible?!
- I've tried to reset my GSM Module by going to the Wallaby bootloader
V 5.14 and pressed the Calendar hardware button. This wouldn’t work.
- I've Flashed the ROM back to the original ppc 2002 ROM (Not the Radio
stack) to get my phone software back (what was lost or unable to start?!)
- Still the phone says no service possible!
- I've Downloaded the T-Mobile Radio stack 6.24.00 and installed it (by
Copying the RSUpdate.exe and files in the windows directory and run it
from the device windows directory).
- After doing this I had a white screen Hang . Luckily after a soft reset it
got back to the radiostack upgrade screen :lol:.
- But Still No Luck so far.
- I've reset my GSM Module again by going to the Wallaby
Bootloader V 5.14 and pressed the Calendar hardware button.
- Turned my device back on and got a simlock warning in W2003!?
- Had to Flash my ROM back again to o2 3.17.03 ROM PPC2002 to be able
to release my SIMlock again With XDAunlock. (worked :wink
- Still no Service !
- I've Installed the new o2 radio stack 4.21 back and
I had Service again!? :lol: :wink:.
- Upgraded the ROM again with T-Mobiles new 4.01.16 ROM.
- Finally it's Upgraded and smooth Working again!!! 8)
HERE IS THE CLUE!:
- I think It had to do with the o2 radio stack upgrade that came in conflict
with T-Mobiles new 4.01.16 ROM.
- So 1st upgrade radio stack in PPC 2002 OS if you have an older radio
(i.a. 4.08) stack before you do a ROM upgrade.
- WARNING: Don't use the T-Mobile band switch 900/1900 function if the
phone is working!!! I found this is also a crucial bug and causes to crash
the GSM module with the o2 4.21 radiostack!
Question: Could annyone tell me were I can find and how I can Upgrade
my Wallaby Bootloader from v5.14 to ........
Thanks and have a good one!
buuuuhhhhaaa :
I'm try to upgrade my Qtek1010 RUU with Pocket PC 2002 ROM Upgrade Utility V1.08.
After the first step, my phone has boot and then I've the message "Impossible to upgrade".
Now, my GSM don't work.
Anyone has a suggest?
Many thanks!
dj
I upgrade my ROM to Pocket PC2003 (T-mobile.nbf) image that worked with no problems using the XDA OS Image tool. It copied over using programme A and following the upgrade I carried our a Radio Stack upgrade to 4.21 supplied by O2. I now have a problem as the phone wont work. I tried re copying the immage again but just before programme A runs a cmd.exe box apears and I get the following message 'ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host.
error getting connectiontype
Programme A then tells me my device is not connected and to check the USB connection. Can any body please help me. All I want is to get my XDA phone up and working again.
Which network are you using, it may be that the bandswitch has chosen 900/1900 which would prevent orange and t-mobile from working, if this is the case enter bootloader, then push the key below the antenna, choose 900/1800 then reboot.
I'm on the O2 (pay as you go) network. There were no problems with my phone and the T-mobile image until I performed the O2 Radio Stack upgrade. I hade already performed this upgrade on my old operating system, before I copied over the T-mobile image. I had no problems with the old OS and the Radio Stack upgrade.
Seamus, if you burn the original O2 rom back to the phone, you will be able to return it to O2 if it is the radio stack upgrade that killed the phone, they should fix it for free.
Hello guys Need some help from the pros
I currently purchased this phone its a Siemis Sx56 AT&T. As i was updating 2 unlock the phone with a dump of another sx56 aT&T that was uncloked (via sd card) it stop in the middle of the proces of uploading the boot of the sd card. Now the phone:
1. Will not start
2. Can not boot the phone to wallaby
3. cooked a rom and tried 2 boot 2 wallaby with no luck
4. 1/2 read & read with no way of knowing what i'm doing wrong
5. how can i repair my bootloader (I used the one in xdtools with no luck)
Than U guys in advance
Luv the Info in the forum.
Adrian
Atlanta GA USA
anyone , i trying to load 4.16 rsu to my xda1 it hang 1% then flash failed restart device. same process again and again
tnx
format failed
g4
IPL 2.17.0001
SPL 1.01
i always use windows mobile 5, it happened when i want upgrade rom. only one rom (rom update utility 2.00.3) works when upgrade, but after restart pda the problem return.
qtek 9100