Hello There,
I've spend my free Sunday on flashing my ROM :roll:
I wanted to warn about a "bug" in the t-mobile 4.01.16 ROM with o2 radio 4.21. Here’s what happened:
I've upgraded from AT&T a.30.09 ROM with o2 Radio 4.08 to t-mobile 4.01.16 ROM with o2 radio 4.21.
- 1st I've installed the t-mobile ROM (SD Flash method Note: ALWAYS DO
THIS!)
- 2nd I've turned off my phone and installed o2 radio 4.21 (through
programB)
Problem:
Every thing went well and there were no errors at all! But:
When I tried to start my phone again there was NO SERVICE possible?!
- I've tried to reset my GSM Module by going to the Wallaby bootloader
V 5.14 and pressed the Calendar hardware button. This wouldn’t work.
- I've Flashed the ROM back to the original ppc 2002 ROM (Not the Radio
stack) to get my phone software back (what was lost or unable to start?!)
- Still the phone says no service possible!
- I've Downloaded the T-Mobile Radio stack 6.24.00 and installed it (by
Copying the RSUpdate.exe and files in the windows directory and run it
from the device windows directory).
- After doing this I had a white screen Hang . Luckily after a soft reset it
got back to the radiostack upgrade screen :lol:.
- But Still No Luck so far.
- I've reset my GSM Module again by going to the Wallaby
Bootloader V 5.14 and pressed the Calendar hardware button.
- Turned my device back on and got a simlock warning in W2003!?
- Had to Flash my ROM back again to o2 3.17.03 ROM PPC2002 to be able
to release my SIMlock again With XDAunlock. (worked :wink
- Still no Service !
- I've Installed the new o2 radio stack 4.21 back and
I had Service again!? :lol: :wink:.
- Upgraded the ROM again with T-Mobiles new 4.01.16 ROM.
- Finally it's Upgraded and smooth Working again!!! 8)
HERE IS THE CLUE!:
- I think It had to do with the o2 radio stack upgrade that came in conflict
with T-Mobiles new 4.01.16 ROM.
- So 1st upgrade radio stack in PPC 2002 OS if you have an older radio
(i.a. 4.08) stack before you do a ROM upgrade.
- WARNING: Don't use the T-Mobile band switch 900/1900 function if the
phone is working!!! I found this is also a crucial bug and causes to crash
the GSM module with the o2 4.21 radiostack!
Question: Could annyone tell me were I can find and how I can Upgrade
my Wallaby Bootloader from v5.14 to ........
Thanks and have a good one!
Related
I have new ROM WM 2003 4.01.16.Is this stable one?While installing exe file it shows current ROM and Upgrading ROM 3.16 How is that?I have downloaded 4.01.16.Is there anything wrong
This is just a header string, it doesn't matter and it will not be shown in the device info as long as you cooked the right ROM.
Some people reported issues in 4.01.16 but not that severe, but I think 4.01.00 is the most stable one.
Softrest Everytime after Upgrading WM 2003 4.01.16
I have sucessfuly Upgraded my Qtek 1010 with WM 2003 4.01.16 by Bootloader method Thanks to Biso007 for his help.But now when Qtek turns off after 3mins It doesnot switch on even after pressing Power Button i tied several times.Now i have to do Resest Everytime or uncheck the box for turning off the device.
Whats wrong what to do I miss calls now.
Can i reinstall the same ROM or any other
Flashed the ROm up fine to 4.01.16. But the Phone won't start up. Dumb Exclamation mark next to signal strength thingy.
Since then it's been Flash-city. I've been back and forth between 2002 & 2003 of various flavours. Most of the time the phone won't talk to the PC anymore either and I have to flash through SD.
What's going on ? I just want my buggy 4.00.05 back right now :-((
marcuskeeler said:
Flashed the ROm up fine to 4.01.16. But the Phone won't start up. Dumb Exclamation mark next to signal strength thingy.
Since then it's been Flash-city. I've been back and forth between 2002 & 2003 of various flavours. Most of the time the phone won't talk to the PC anymore either and I have to flash through SD.
What's going on ? I just want my buggy 4.00.05 back right now :-((
Click to expand...
Click to collapse
First procedure to do is there's a label on the back of your unit saying PW10A1 or PW10B1 well the first is for 900/1800 and the second for 900/1900 .
Goto the bootloader and check if it's still GSM OK, if it does then don't worry you could make it back to business bcz you might flashed your RSU part with the wrong version, or you setted the Gsm on the wrong freequency to fix the wrong setup :
1- Turn off ur device
2- press on the power buttom + the hard reset buttom
3- you should see (GSM OK)
4- press on the callendar buttom
5- select the frequency 900/1800 or 900/1900 depending on your device
6- press on hard reset it again
PS: this will erase all your data from the ppc.
If it didn't work out with you then it's possible now that you flashed your ppc with the wrong RSU version depending on the back label.
This link could help you http://forum.xda-developers.com/viewtopic.php?t=9833&highlight=
If your device is a PW10A1 Flash it with RSU 3.25.00 Ver. If it is PW10B1 then flash it with RSU 6.25.02 Ver.
Good luck to you now.
yes!!
i am verry happy
a few days ago i have upgraded ppc 2002 to ppc2003 andsuddenly i also had radio rom version 4.21.00 and there was no way that i could get the gsm radio part working or i couldn't even downgrade to radio version 4.16 orso
until i saw this message with the verry good tip from ramram.
now it is working verry fine here with radio rom 4.21.00
thanks for that !
nobody khows how to pass 1% in radiostack upgrade
Radio stack upgrade failed
I have a T-mobile pocket pc phone ROM version 3.14 which I bought in the US. When I tried to upgrade the radio stack programme B ver 4.21 from O2, the RSU says "flash failed. Press OK to restart your device". I have not been able to go beyond 5%. Could someone help me with an old RSU which can get my pocket pc phone back in order.
I upgrade my ROM to Pocket PC2003 (T-mobile.nbf) image that worked with no problems using the XDA OS Image tool. It copied over using programme A and following the upgrade I carried our a Radio Stack upgrade to 4.21 supplied by O2. I now have a problem as the phone wont work. I tried re copying the immage again but just before programme A runs a cmd.exe box apears and I get the following message 'ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host.
error getting connectiontype
Programme A then tells me my device is not connected and to check the USB connection. Can any body please help me. All I want is to get my XDA phone up and working again.
Which network are you using, it may be that the bandswitch has chosen 900/1900 which would prevent orange and t-mobile from working, if this is the case enter bootloader, then push the key below the antenna, choose 900/1800 then reboot.
I'm on the O2 (pay as you go) network. There were no problems with my phone and the T-mobile image until I performed the O2 Radio Stack upgrade. I hade already performed this upgrade on my old operating system, before I copied over the T-mobile image. I had no problems with the old OS and the Radio Stack upgrade.
Seamus, if you burn the original O2 rom back to the phone, you will be able to return it to O2 if it is the radio stack upgrade that killed the phone, they should fix it for free.
Hello guys Need some help from the pros
I currently purchased this phone its a Siemis Sx56 AT&T. As i was updating 2 unlock the phone with a dump of another sx56 aT&T that was uncloked (via sd card) it stop in the middle of the proces of uploading the boot of the sd card. Now the phone:
1. Will not start
2. Can not boot the phone to wallaby
3. cooked a rom and tried 2 boot 2 wallaby with no luck
4. 1/2 read & read with no way of knowing what i'm doing wrong
5. how can i repair my bootloader (I used the one in xdtools with no luck)
Than U guys in advance
Luv the Info in the forum.
Adrian
Atlanta GA USA
Hi...
I upgraded my qtek 9100 from OS version 1.6.7.1 to cingular 1.8.11.1
The problem is that now, the phone doesn't start... the splashscreen appeears, along with... IPL 2.17
SPL 2.21
GSM 02.07.10
OS 1.8.11.1
But doesn't get out from there...
Did a do anything wrong?
PLEASE help me?
Is there any solution or is it bye bye qtek?
maybe you flashed broken or wrong rom.
start your device in bootloader mode (look in wiki how to do this) and then reflash again and if this does not work, get rom from your provider and reflash with this.
...
But my pda starts and it stays in splashscreen... is it repareble anyway?
Yes it should be fixable
Cant understand why you would want a old cingular rom (the cingular is not exactly same hardware as your phone wiza200 vc wiza100!)
You should download an aku2 rom here ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
user name xda password xda
Next get into the bootloader screen - turn device off and start with camera button pressed - should be a multicolor screen
Next attach device to pc via usb cable
Flash with above rom and all should be well