Related
I've just got back from work having lef my XDA II on O2 at home, and the thing won't turn on!
When I plut it into the charger, a faint red light comes on (where the green signal indicator usually is), However after a few minutes charging it should deffinitely turn on, yet it still does not.
Does anyone have a clue whats going on??
If the main battery and backup battery run out, shouldnt sticking it in the cradle charge it?
Any help much appreciated
Try removing the main battery for a while then try again.
I've had a few of such experience. It won't turn on. Even charging it from the power main, soft reset, take out main battery for a minute or half...
The only way to wake it up is to HARD RESET.
Strangely, I thought somehow the battery ran dry, but after one hard reset I noticed the main battery was at normal level, backup battery 100%. How frustrating. It happened a few times already.
8) I also found this problem. I use Spritebackup and schedule to backup everday at midnight. So, I can restore after have to do hard reset
What ROM version are you running on your XDA2?
I had the same problem on my MDAII and I was on 1.60.00WWE but an upgrade to 1.72.00WWE fixed the problem. That ROM also used to wipe my SD Memory!... Now I'm on 2.06.00WWE (Windows Mobile SE) and it's better than ever!!!
Good Luck!
Rayan said:
What ROM version are you running on your XDA2?
I had the same problem on my MDAII and I was on 1.60.00WWE but an upgrade to 1.72.00WWE fixed the problem. That ROM also used to wipe my SD Memory!... Now I'm on 2.06.00WWE (Windows Mobile SE) and it's better than ever!!!
Good Luck!
Click to expand...
Click to collapse
I had the problems when I was on 1.60.00WWE. Since the very last hard reset (device not responsive to soft reset after a flight in February), I changed it to Sin's Merged ROM version 2 (WM2003SE). I wouldn't say it's better than ever, as I noticed the device is slower but it has been ok ...
I just joined the list because of this issue.
I have ROM Ver 1.72.00WWE and Radio Version 1.17.00.
I only upgraded both ROM and Radio in the past fortnight. It's only since the upgrade that I've had the problem of not being able to 'wake' the XDA and having to do a 'ahrd' reset. I have also another issue regarding the GPRS connection but I'll write a separate email on that.
Seamie
XDA II Problems
Its nice to know other people have the same problems.....
I have had similar problems and either just remove the battery or do a soft reboot. As I travel a lot, I can't get to my desktop to back up. So I use a 1GIG SD card. But I have'nt lost any data yet.
One annoying problem I had was the damn thing kept switching on every time I picked it up or put in the hard case, or even just laid it down. It seems to have disappeared now. Has anyone else had the same problem? :roll:
so its fate!
check in this morning and mine is doing nothing, nada, zip
hmm soft reset nothing check the threads and this ones at the top!
used all day yesterday sitting on the charger overnight and bingo its dead...
Same problem
Have had intermittent problems with being able to turn on. Took battery out for a while and when it decides to work it automatically has performed a hard reset. Use daily for receiving jobs, recording serial numbers using BT scanner and then e-mailing. As well as being my phone and GPS. Have started taking my laptop with me just so I can restore data on the run.
What a pain!
XDA Problems
From the replies given it appears that the problem lie swith the battery. Has anyone raised this with the supplier? I was thinking of getting a spare one, but they are a bit pricey.
I honestly don't think it's the battery that's at fault. This is because I didn't have any problem with my XDA II until I upgraded the ROM and Radio recently. Secondly, it happens irrespective of whether the battery is fully charged, half charged ... whatever. IMHO, it's whatever was done in the upgrade!
When I got mine back from repair the battery was totally drained as well as the back up battery. would do nada, not switch on, nothing whatever I did.
A few minutes on the charger was not enough. You have to leave it in for about 14 hours once it's in that state for it to become live again.
Don't ask me why, but it needed at least 14hrs on that mains charger !
I too suffer this problem .... only since upgrading too.
Will try the Spritebackup method
guys i have a similar problem. my power button has broken and i turn on the device with the record button (i have remapped the buttons). Yesterday i turnd it on and the screen freezed on the today screen . I performed a soft reset, the screen went blank and it never turned on. Now the device is dead, soft reset won't work, it doesn't seem to charge (no light when i put it on the cradle) and i cannot perform a hard reset because i do not have a working power on/off button.
Is there anything i can do to turn it on?
Before the experts arrive, you could try removing your battery and simcard and leaving them out for a good 15 minutes they try again.
I broke the power on button off my last xda, my hubby soldered it back on
I've had the same problem since 10 days now. First time (friday), the phone just reset itself (hard reset) without reason... 4 times within 2 hours. When I came home i reloaded it for 12 hours and restored a backup. It worked fine from saterday until wednesday.
Then on wednesday it reset (hard reset) itself almost 10 times. Thats the first time i noticed a red light when I tried to recharge. The red light dissapeared after a couple of minutes and the phone would switch on again ... in hard reset mode. Again I left it charging a whole night and restored the backup the next morning. It worked fine again until ... yesterday (monday)... I dropped it (stupid me). It went completely dead. Even when recharging for 2 hours the light was still red. A new fully charged battery (my first thought) did not help a bit.
This morning I opened it up (its about 18 months old, so no more waranty) and i found nothing. When i closed it up... it did a hard reset !!! I changed nothing inside (I even found a little piece of metal afterworths that must have fallen out!). I suspect it was the fact that i removed the battery AND the SIM-card for more than 30min that did the trick. My phone is not SIM-locked (illegal in Belgium to sell sim-locked phones, good thing, but they are a lot more expensive here too). A brand new battery did not help.
Problem is ... when I send it in for repairs, it will be gone for about 4 weeks ! And the best they can do is give me a Sony Ericsson P900. I appreciate their effort, but carkit wont work, no GPS, etc... so i would rather try to solve the problem myself. I'll contact the repair center today and see what they suggest. I'll keep you posted
Cissen, how did you get on? Have you found an answer to your problem yet?
Edit: Mine crashed again yesterday and it showed the battery as being empty although I had fully charged it the day before.... so, I have now ordered a new battery.
They are pretty pricey for branded ones but I found this site yesterday so have ordered one from there - only 20 pounds including delivery so not wasted too much if they're crap
http://britishpound.ecyan.com/batteries-chargers/batteries---mobile-phones-and-pda---o2.shtml
I've got this problem too, when I first got it, it turned for about three seconds then turned off, so I thought it was a dead battery. but when I put the battery in there is no charging light, I have tried 2 different batteries that work fine in my other xda IIi. If I take the battery out and place in the charger a red light comes on.
Ei guys. this is a bit different from your experience. Anyone experienced by just changing battery it went hard reset? or just by changing sim card on the phone, removing the battery just for a second the phone went hard reset although I did checked the backup battery which is in 100%. Anyone?
Hi,
i have a QTek S100. Since a while it says always that it is charging the battery even when it is not attached to the powercable. I changed now the battery because i thought the battery is broken but it wasn'nt. Has somebody a idea what I can do?
When in the charging status the battery holds only for 6 hours, because its not going in standby mode...
Please i hope someone of you know how to fix that. I love my S100 but its so annoying, to recharge it all the time...
Thanks!!!
Have you tried a hard reset?
how to do it: Press simultaneously for 1 sec, the power button and the reset hole.
(note: You will loose all your files/contacts/sms/programs, etc - Do a phone backup 1st)
Regards,
Keeper
Editing this as I'm desperate for help and things have moved on since I first posted, below is where I am up to post 11 of this thread.
I flashed Vegacomb b (exe), it restarted but stayed on the warning about paying for vegacomb for 10-15 minutes which didn't seem right so I held power for 6 seconds and it turned off. After that it would never turn on or go into recovery (I know all the methods, none worked).
Today I unhooked the battery, when I plug the battery back in the screen comes on for a second but then it's as it was, unresponsive. HOWEVER, if I plug the mains in with the battery disconnected then it immediately tries booting but still sticks at the warning (left for over 20 minutes). If I plug the battery in while on this screen then remove the mains it stays on. The power button is unresponsive through this so I still cannot get into recovery.
Any more ideas that haven't been mentioned?
I've tried well over 100 times to get into recovery but it's not happening
anyone willing to have a go at fixing (cheaply!) if I send them it?
Original Post:
Hi guys, just managed to (re?) install Vegacomb (b, from exe), it restarted but stayed on the white screen with the warning text about paying for Vegacomb for over 10 minutes so I held down the power button to turn it off, now I cannot do anything to boot it up (tried holding power button down from 0.5 seconds to 60 seconds!), it also won't boot into recovery. Is there anything at all that can be done to get this going?
cheers
OK, I've tried holding down back while plugging in (fully charged btw), tried all variations of button presses with back and power, with and without USB, with and without power cable.
Only got until 10PM (UK time) to get this sorted (it's now 6PM) so any help/advise would be appreciated
Flash back to modded stock then try again.
From modded stock go app drawer and run recovery
From recovery wipe data, cache then go advance then wipe dalvik
Then press back
Then install zip from SD
Choose vegacomb from whatever directory on your SD you copied it to then confirm
If you ain't Got Vegacombe zip then download it.
Or you could run the .exe again but the above is my preferred method.
Also you might need to download modded stock v2 if you ain't already got it.
Good luck.
intel007 said:
Flash back to modded stock then try again.
From modded stock go app drawer and run recovery
From recovery wipe data, cache then go advance then wipe dalvik
Then press back
Then install zip from SD
Choose vegacomb then confirm
If you ain't Got Vegacombe zip then download it.
Or you could run the .exe again but the above is my preferred method.
Good luck.
Click to expand...
Click to collapse
??
the Vega won't turn on and won't go into recovery, cannot flash anything, nothing comes up on PC, tried all variations of the back and power buttons (inc back, plug in power & usb, press power, leave 2 seconds and release back) over 100 times. it's like it's dead.
the only thing it does is show a blue LED when I plug the power cable in
I've read that if you got less than 50 or 60% battery it wont go into flash mode (back button 2 seconds - power & back 2 seconds)
Have you got enough battery cause mine takes half a day to charge.
intel007 said:
I've read that if you got less than 50 or 60% battery it wont go into flash mode (back button 2 seconds - power & back 2 seconds)
Have you got enough battery cause mine takes half a day to charge.
Click to expand...
Click to collapse
100% (solid blue LED), been on charge for over 24 hours
I'm baffled mate, I've had same issue couple of times but after 10mins or so I've always got it to power back on.
Bricked
I've had the same problem and although quite drastic, remove the rear cover and unplug the battery connection (the multipin one with red and brown/black wires).
With the mains plug out,i found that if you press volume up and power with the wires unplugged and leav eit for a few mins then use back + power it will start as you need it to.
It may take a few tries but i have managed to do it following this procedure about 7-8 times.
Hope this helps.
DAve
I had trouble getting into recovery when the Vega was 100% charged (i.e. charge led was solid blue). When I let it discharge a little so it was flashing with the charger plugged in, I managed to get into recovery then.
dmarchant said:
I had trouble getting into recovery when the Vega was 100% charged (i.e. charge led was solid blue). When I let it discharge a little so it was flashing with the charger plugged in, I managed to get into recovery then.
Click to expand...
Click to collapse
I can't discharge it though as it doesn't turn on, left it 14 hours from last night, back at work again now and it still says fully charged
got the battery disconnected now to give it a try
Disconnected battery for around 10 minutes, put it all back together, still can't boot or get to recovery
EDIT: it works when the battery is disconnected (goes to the Vegacomb warning screen but no further, cannot power off or get to recovery still)
any ideas?
Anyone got any ideas?
it's meant to be unbrickable from what I've read so there must be a way around it but I'm out of ideas!
its user error. remeber to put it into recovery mode you need the power cable plugged into it too as well as usb.
slybunda said:
its user error. remeber to put it into recovery mode you need the power cable plugged into it too as well as usb.
Click to expand...
Click to collapse
Cheers, but its not user error. I'm not that stupid
Hi, this may not help but i had trouble flashing the stock rom because of the battery being fully charged, could only get the screen to light up so left it over night and then went through the normal routine and got into recovery.
Bill
Hi there
Just one question, how do you know for sure it hasn't gone into nvflash mode?
I know what you are going through trying to get the ruddy thing into nvflash, it's a mare if you don't quite get that timing right but seeing as the screen doesn't light up when it's in nvflash what is telling you whether you are actually in it, other than the screen coming on to say you are not or relying on a windows message?
As I said I had the same problems many a time but I use Audi tool now to tell me if nvflash has started, I got it off the Modaco forum, but when you are in nvflash it actually tells you so rather than relying on perhaps windows to tell you it has happened
If you haven't come across the audi tool before then just do a search for it on Modaco, I don't know if they have got it here on XDA.
mmace said:
Anyone got any ideas?
it's meant to be unbrickable from what I've read so there must be a way around it but I'm out of ideas!
Click to expand...
Click to collapse
wow, i'm quite surprised by the number of people who are taking their batteries out when they think there is a problem. You should never need to do this unless it is actually faulty.
Ok yes the Vega is nearly indestructible I have had my in a complete mess many times and have never had to do anything that hard to recover. Some times it will be a pain to get into nvflash mode but this can always be done just have to be patient and know a couple of tricks.
If you have tried the back button and then the power a few times and nothing there is another method.
Instead unplug the power then hold the back button down, whilst holding down the back button plug in the power release the back button after a couple of seconds (I like to count to 5)
I am hoping that you already have the USB cable connected and the right drivers installed on your PC.
Billy..
If you need more help head over to TabletRoms and look in the Vega forum (sorry XDA guys just there is a lot of other useful information there)
wks said:
Hi, this may not help but i had trouble flashing the stock rom because of the battery being fully charged, could only get the screen to light up so left it over night and then went through the normal routine and got into recovery.
Bill
Click to expand...
Click to collapse
I've tired fully charged and letting the battery drain for 40+ mins after it's been on the "warning" screen
mitt69 said:
Hi there
Just one question, how do you know for sure it hasn't gone into nvflash mode?
I know what you are going through trying to get the ruddy thing into nvflash, it's a mare if you don't quite get that timing right but seeing as the screen doesn't light up when it's in nvflash what is telling you whether you are actually in it, other than the screen coming on to say you are not or relying on a windows message?
As I said I had the same problems many a time but I use Audi tool now to tell me if nvflash has started, I got it off the Modaco forum, but when you are in nvflash it actually tells you so rather than relying on perhaps windows to tell you it has happened
If you haven't come across the audi tool before then just do a search for it on Modaco, I don't know if they have got it here on XDA.
Click to expand...
Click to collapse
I have Audi, I also have Device manager open, I know 100% it's never gone into recovery mode sine I started with this problem.
BillyFish said:
wow, i'm quite surprised by the number of people who are taking their batteries out when they think there is a problem. You should never need to do this unless it is actually faulty.
Ok yes the Vega is nearly indestructible I have had my in a complete mess many times and have never had to do anything that hard to recover. Some times it will be a pain to get into nvflash mode but this can always be done just have to be patient and know a couple of tricks.
If you have tried the back button and then the power a few times and nothing there is another method.
Instead unplug the power then hold the back button down, whilst holding down the back button plug in the power release the back button after a couple of seconds (I like to count to 5)
I am hoping that you already have the USB cable connected and the right drivers installed on your PC.
Billy..
If you need more help head over to TabletRoms and look in the Vega forum (sorry XDA guys just there is a lot of other useful information there)
Click to expand...
Click to collapse
TabletRoms has been no help for me, there's been no reply at all for my problem but there has here and at MoDaCo. I pulled the battery as a last resort as NOTHING is working, I've tried all the tricks at least 2 dozen times, some a hundred +, including the one you mention
Well I don't want to teach you to suck eggs, but I take it you did use Audi to delete and replace your drivers.
And then when powering on the Vega you held the back button for 2 secs and then the back and power buttons for 6 secs to get the Vega detected?
For me I can only see that there can only be 3 other possible causes
1./ the back button is broken on the vega
2./ The USB port on your PC or on the Vega has gone up the swanee
3./ The USB lead is no good
The Vega may be unbrickable but if the back button or the USB port has had it then .....
Yeah, tried it, cheers.
Today i got a call from a friend but my phone restarted. After that my power button stopped working. I reflashed Siyah v3.4.1 but same problem. It is strange that when i pres Vol+ Power Button and Middle button combo for entering recovery it is working ........I am on Wanam v12.2 Phenomenal kernel v5.5 Medium. Can some one help me please, i do not want to use my warranty because i need my phone right now and if i sent it maybe my repair will take at least 2-3 weeks time...
Strange thing happend again! I wiped everything, change kernel and recovered a backup 2 days before today but it was the same ... no power button. Now after a 100% recharge, turn on USB debugging and a connection to PC my Power button is working again :victory: Is that bizarre or what?!?!
Hi,
I slept last night with ~40% in my OP6T. When I woke up, the phone wont start anymore. I am rooted with the latest Magisk, and latest stock rom.
When I press the power power button, it doesnt even show me the screen where I have the bootloader warning. I've tried pressing the power key alone for 15 seconds, power + up volume for 15 seconds , power key + down volume for 15 seconds, power key + both volume keys for 15 seconds but nothing happens.
I just cannot get my screen to start:crying::crying::crying:
I have also tried connecting my phone to the laptop, I get a "safely remove OP6T" notification in the task bar, but my phone inst identified in the storage..
If anyone could help me, that would be greatly appreciated.
Thanks a lot
TarunN5 said:
Hi,
I slept last night with ~40% in my OP6T. When I woke up, the phone wont start anymore. I am rooted with the latest Magisk, and latest stock rom.
When I press the power power button, it doesnt even show me the screen where I have the bootloader warning. I've tried pressing the power key alone for 15 seconds, power + up volume for 15 seconds , power key + down volume for 15 seconds, power key + both volume keys for 15 seconds but nothing happens.
I just cannot get my screen to start:crying::crying::crying:
I have also tried connecting my phone to the laptop, I get a "safely remove OP6T" notification in the task bar, but my phone inst identified in the storage..
If anyone could help me, that would be greatly appreciated.
Thanks a lot
Click to expand...
Click to collapse
It's probably out of charge, happened to me and I just left it on charge for 15 minutes and then held the power button and it worked.
TarunN5 said:
Hi,
I slept last night with ~40% in my OP6T. When I woke up, the phone wont start anymore. I am rooted with the latest Magisk, and latest stock rom.
When I press the power power button, it doesnt even show me the screen where I have the bootloader warning. I've tried pressing the power key alone for 15 seconds, power + up volume for 15 seconds , power key + down volume for 15 seconds, power key + both volume keys for 15 seconds but nothing happens.
I just cannot get my screen to start:crying::crying::crying:
I have also tried connecting my phone to the laptop, I get a "safely remove OP6T" notification in the task bar, but my phone inst identified in the storage..
If anyone could help me, that would be greatly appreciated.
Thanks a lot
Click to expand...
Click to collapse
Hold pwr and up button for a couple of seconds.
So after 1000s of attempts, its started on its own (on the 1001th ) attempt when I held the vol up and pwr button. It wasnt a case of battery drain as I had only connected it to the system for 10 mins and the battery when it started was 53%.
Is there a way to find out how it tuned off ? some crash logs or something ?
Can an admin please close this thread ?
Yeah it seems like there's an issue with the phone loading up after it's went dead..and I've had that issue a few times where I had to play with it for an hour in order for it to finally load...I even knew it was dead and plugged it up to a charger and it would stay on the bootloader screen and I left it on the charger for an hour or so..and then held the <pwr><vol+> to shut it off and when I did all that I then powered it on and took the charging cable out and it still said it was low battery..so while on the unlocked bootloader screen it wasn't charging(weird)..so after fooling with it summore I finally got it to charge just random didn't do anything I hadn't previously done and all was good. But it seems like this only happens after it dies and I don't Kno if the unlocked bootloader is the issue or what but it's aggravating to have to fool with it for that long.
I think there is something wrong with your ROM.. Are you rooted? If I were you, I'd wipe the phone completely and install a new Rom, redoing the setup from scratch..
I have wiped and rooted with magisk and twrp recovery installed.. and I have zero issues in the current setup..now only when it has died did this seem to happen..oh I have wiped 3x because of bootloop and soft brick previously..so I don't think that is the solution (wipe and clean install)..just weird
smiles19 said:
I have wiped and rooted with magisk and twrp recovery installed.. and I have zero issues in the current setup..now only when it has died did this seem to happen..oh I have wiped 3x because of bootloop and soft brick previously..so I don't think that is the solution (wipe and clean install)..just weird
Click to expand...
Click to collapse
I haven't tried this, but from what I've read, using the MSM tool is the only sure way to completely factory reset your phone.. Using anything else could leave remnants in the ROM causing problems..
gregwee said:
I haven't tried this, but from what I've read, using the MSM tool is the only sure way to completely factory reset your phone.. Using anything else could leave remnants in the ROM causing problems..
Click to expand...
Click to collapse
For some reason my fastboot drivers are not working anymore, the MSM tool is not a option for me.