XDA1 after ROM update battery don't charge fully - MDA, XDA, 1010 Software Upgrading

Hi all
I need help. I just upgraded the rom of my XDA using the XDA-Developers SER 1.2 ROM 2 days ago. I fully charged the battery before I upgraded the rom and upgraded it successfully. But after I upgraded, when I charge, the battery I seems to charge “forever”. The light indicator would not turn to green which indicates that the battery is fully charged. I did hard reset twice already (after the upgrade). What do you think is the problem? Thanks

Need help pls

since the delveloper rom is kinda old most people cook their rom based on much newer roms in the kitchen's
why did you pick the developer rom ?

Thanks for the reply. I chose the Developer's ROM beacuse the time that I want to upgrade, almost all the rom kitchen sites are unstable and always offline. And most of them do not cook the rom properly , will just give me 300KB rom instead of a 15MB. Will there be a problem if I upgrade the ROM again, I want to upgrade to WM2003. Can you suggest a site where I can just download the ROM, or a more stable kitchen?
I'm also hesitant on upgrade becuase I only upgrade via exe file and usb brando cable, coz I dont have an SD Card and card reader. Pls give me a url for a stable WM2003 rom for my XDA1. Thanks.

pjfuerte - I have been recently having the same problem, but I am on a newer WM 2003 ROM.
What I am actually finding is that if I charge the phone using the cradle, it charges fine and without problems. If I charge with just the power cable and accessory plug (22-pin to DC Jack Converter - see second item in http://www.myqtek.com/Accessories.aspx) the orange light never disappears and I actually have a problem using my phone as if the battery hasn't charged successfully.
I think this is actually due to over use of this plug - I don't think the pins are lined up properly anymore and I can see some damage has occured over time.
Does this relate to you? Try charging the phone using the alternative method to the one you are using now. Cheers, Doms.

Domino,
Did u upgrade via EXE file? Can you give me the rom exe file for the upgrade, that least I know that file is correct and stable.
Before I upgraded to the current ROM that I'm using, (I upgraded because I want to unlock the device) I've been charging with a replacement charger. But it charges fine, and the orange light will turn green if charge is complete.
I also sync via Brando USB replacement cradle. And upgraded the rom via the said usb cradle. After upgrade, the orang light woudnt turn to green and wouldnt specify that charge is complete. I don't have the original accessories the unit was just given to me.
Do you think it is becuase of my charger?

Related

Prophet does not start

I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Does it show any serial number on the bottom of the screen or does it just show a blank screen.
What you could do is remove the battery, SD card out and leave the device like that for about an hour or so. After an hour just insert the battery (not the SD card) and then try charging again. Let it charge for about half n hour and then try switching on the device. Most likely, your device will now wake up, if it doesn't then you will probably need to wait till the amber light turns green indicating a full charge. Try switching on the device again, if still no luck, then you will need to take it down to a service centre.
It works when using power adapter, but not on usb
The prophet does start up when using the power adapter, but not when on the USB. Have left it 'charging', but the charge light is not on.
USB only provides a trickle charge and hence is not the best solution for "waking up" a device. Always make sure that you charge your device through the provided AC adapter. Only in cases of emergency or when synchronisation allow USB charging.
No charge light
No charge light is on. Is that right?
If there is no charge light, that means its not charging to begin with. Can you check if the USB port you are charging from is functional by attaching another device to it. Incase the USB port is fine, try charging from a different USB port; if it still behaves the same way, i suggest you take it down to a service centre. Its quite possible that the charging port on the Prophet is damaged.
sam_sykes said:
I have a new Prophet (JAMin) and it does not start, even when charged. All that happens is the lights at the top flash, the screen blinks and then no more.
Any ideas, as I need the device later!!!
Click to expand...
Click to collapse
Mine used to be like that after I installed spb plus previous version, it wont start at all...I had to switch to a new machine (for free) coz it was only day-2 after i bought the device (nice service btw).
Cheers!
I Have an SPV M600 which when switched on the screen blinks and then powers off, no charging light will only power up with the charger plugged in not with the usb data cable, i used a file called hard_SPL-G4 since then this error occured i think its the software program loader.
I cant reflash via active sync because the device powers off without the AC charger. i do have SD cards, but im unsure how to flash from SD i want my original spl version back and a better OS.
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
I can get to the tricolour screen bootloader with charger plugged please help any advice?
these are the original settings i think
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Once it is in bootloader, can you switch it to the USB cable?
Q: Once it is in bootloader, can you switch it to the USB cable?
A: no it switches the power off when i unplug AC but i can get to the windows OS if i power on with AC..? but flash via activesync no AC on reset.
I do have two SPV M600s im not touching the working one. but would like to fix the other one. SD Flash would help possible corrupt OS or SPL i think?
i can gain access to bootloader but i dont know how to initialize the NBH rom,
i could start the extrom cabs which had an autorun with a list of execution
i updated the rom Mysterious_1.0 all went ok i think
then i ran hard_SPL-G4 i had a lot of errors about sleep4.exe not win32 i think.
i am running x64 pro and upon reset all i had was an occasional screen blink and weak flashing orange and blue led.
ive tried different battery and a different USB to miniUSB. the active sync does take long time looking for changes on OS.
from usb i hold camera button and click reset switch it goes to USB bootloader for a second then off
if theres anyone out there who knows how to reflash the SPL version and a new OS for an SPV M600 english lang from an SD card please link files and explain the process in as much detail please? thankyou!
i did also update the radio version GSM could that be a cause!
The radio version should have nothing to do with it...
I am fairly sure there is something on the wiki about flashing from a storage card, but you need to make the dump of the ROM from the working device, so not much help there...
If you can get into bootloader whilst it is plugged into your computer, it's a very easy problem to fix...
I have decided to find the pinouts for a 4.5V charger (it should be 5V but im not destroying original) and a spare USB-miniUSB attach the power terminals from the charger replacing the miniUSB charge terminals, which should allow me to go to bootloader with USB present. i will post my results in here soon
about accessing bootloader
Hi i have just executed the jump spl files on my problem device and its taken me to a white screen with usb data cable, which i heard is the bootloader really and used tera term pro to dump rom etc. its seems to of hanged at the minute does it take a while to write?
im guessing i could go into the white screen mode and reflash an original orange rom?
New Original OS installed
Hi ive successfully installed a new OS so i presume the white screen is a bootloader. still my problem of powering off upon boot exists, so using this method i want to change the details below
OLD SETTINGS
IPL 2.21.0001
SPL 2.21.01ip
GSM 02.69.21
OS 7.7.7.7
NEW SETTINGS
IPL 2.10.0001 check
SPL 2.21.01ip SPL 2.10.0001 wanted
GSM 02.69.21 GSM 02.07.20 wanted
OS 2.10.1.22 check
Can i reinstall the wanted SPL/GSM from the white screen loader? does anyone know where i can get the files. SPV M600
Repaired 100%
I did it, its fixed charges now from USB data cable. and can enter tricolour bootloader. the problem was something wrong with the spl flash process ive redone that no errors excellent. im happy now
Will a ROM flash now?

Prophet upgraded with Wizard ROM by mistake

Just tried to upgrade my S200 with a 9100 ROM ver 2.8.7.1 WWE (by mistake of course) and I can't turn it on anymore. Somehow it didn't even warn about wrong ROM.
Tried to hardreset it but no luck. When I keep the camera button it goes to RGB only when connected to the charger.
When connected to PC, the red and blue leds keep flashing and my PC gives Error 260 when I try to revert back to the S200 RUU.
Does anyone know how to bring it back to life? Is there a way to boot it from SD card?
-
I-mate Jam
Qtek 9100
Qtek S200
Don't panic!
I did the same thing some time ago!
What you need to do is make sure that the battery is fully charged. (The flashing of the screen can be a result of the flat battery.) Unfortunately, it is not possible to charge the battery when the wrong ROM is installed, as the ROM obviously tells the Prophet how to charge.
Let's assume you have an okay battery.
1) Start the Prophet in Boot mode. This is done by pressing and holding the Camera button and then pressing the soft-reset button. Keep holding for about 7 seconds, and the coloured bands should appear.
2) Connect to PC using the UDB cable.
3) Run the correct ROM upgrade. You do not need to be paired with ActiveSync, as the update programs are intelligent.
4) If the update does not work (and it fails at 95%), then try again. If it still fails, try again and do a soft-reset mid-way through. This will kill the ROM upgrade and you should then be able to do it fine after that.
The really important thing is that the battery is charged before you do this. Unless anyone makes a USB cable that can charge AND connect to PC, then a fully charged battery is a must.
Let me know if this helped.
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Re: Boot from SD?
zealerc said:
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Click to expand...
Click to collapse
I am a bit confused, does that mean that ALLOW USB CONNECTIONS has to be chacked or unchecked?
I did the same exact mistake. Now, my baterry is fully chaged (which I can check on another phone) but when I put it in S200 it shows that the battery has 0%. Conseqeuntly, when i unplug the power cord the phone dies. I have no way of running the new ROM on it. I tried running a bootable SD but it only installed part of the software. i read on this forum that such a thing happens and that one would need to run a full version ROM from a computer. So, how do I do it??? I am almost giving up all hope of ever making this phone work
Does anyone have a file to boot from SD and is it possible to run a full ROM from SD. Please help!

MDA dead

Hi,
after the download new ROM my MDA was fired!!
First I download a customized ITA rom and after, because the MDA work very slow, I downloaded the latest T-mobile ROM.
Now the MDA do not power up and do not charge the battery.....sems dead.
Can I recover it?
just an idea but I would start by trying to charge it with the wall plug that came with it, not a computer usb cable - if the battery is all the way dead it will not charge from the computer. If the light comes on, let it charge for a while and then try it out. If not I would try to hard reset while it is plugged in. If none of this works, enter bootloader mode and then connect it to the computer, and hopefully it will go into bootloader mode and you can flash a new rom.. If you need more details on how to do any of this, let me know, and please let me know if it works!
Hi....you fine.
I have recharge the battery and dowloaded the original Tmob rom.
Now is strange..
Same time power up...and same time no.
The ipl is 1.06 and spl is 1.03!!
My Qtek 9100 is dead also. I have the 2.24 ROM and it has been running great. I cant power it on and the light doesnt turn on when its plugged in. The battery is definitely not dead. Suggestions? TIA
try this...
try the suggestions listed here
however be warned that any of these will delete any and all data that may or may not still be on your device and restore it to just the fresh ROM...
Hi,
I have flash the rom 1.6 Tmob (IPL 1.06 SPL 1.03) but the MDA restart in loop mode!!
My phone powered up today. It's been sitting on my night stand for a week and it turned on today! Everyday I have tried to turn it on but I haven't had any luck until today...weird!

Pls help ti solve NO GSM problem!

Could anyone can help me to solve No GSM poblem. I think there are many other users have same problem.
After it faild during update rom, My HP6915 represent NO GSM during booting and the phone funcation also doesn't work. But in HP Asset you can see it, just no firmware, no version number. I try to flash english radio rom and french radio rom, but always stop at 1%. This matter appeared after I flashed orange rom(french version). I think it locked by Orange.
Does any one can help us?
did you try the update with no sim and no minsd?
EREZYAD said:
did you try the update with no sim and no minsd?
Click to expand...
Click to collapse
Yes, I update without sim card and minisd. Always stop at 1%
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
EREZYAD said:
to be on the safe side i will go over general insraction
battery full
recomended xp os & activesync 4.5 (not beta)
minsd & sim out
ac addapter connected (ac power from orig transformer)
hart reset your device before the update
connect device directly to computer's usb plug
run the update
try radio only &/or the all update you can also try on a different pc
if all didn't work read this and see if you can find somthing that works on the 6900
http://www.htcwizardweb.net/node/170
good luck
Click to expand...
Click to collapse
Thank you for your reply!
I tried but still same, stop at 1% when I flash Radio WAN OS, stop at 2% when I flash Radio FS. I tried to unlock simlock and CID unlock, but it doesn't work on my 6965
called a few places looks like the radio chip is fried. sorry man...not looking good.
try update again with this method
I got almost same problem. I tried to update GSM rom but update fail and my ipaq stuck at hp invent logo. try following steps to see if it works for you
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
I also meet such question.
actualy. I met the same problem "No GSM" after wrong update. I thing I tried everything, but I Didn't try to flash the device via mini-sd card. I don't know the right address for GSM area. Did anyone know?
caoxt said:
I also meet such question.
Click to expand...
Click to collapse
COME ON guys some one can help us , i have too the same problem please help with radio stack !!!!!!!!!
me too,, really nedd help here.. my only phone sable...

no battery charge on Blackstone

Hi
Since a few weeks, I'm no longer able to charge my blackstone via USB cable when it is powered on, Orange light isn't working. When I plug my HTC to a {windows|Linux} anything happens. It is no longer recognize by the system.
I have had an old image of android and try to see if i can charge through it and It worked. I decided then to upgrade to Xandroid 2.01 rev 2.4 but it doesn't work anymore.
I have tried:
Many HR
Many reflash
Upgrade of my Radio
What I cannot do :
task29 - the procedure says that I have to use the USB...
I suspect a faulty wall USB charger used for recharging my HTC.
My blackstone can only be charged when powered off (for the record, it charges very fast to 100%). I can synchronize via bluetooth and test ROM via BLACIMG.NBH on SDcard. Wifi and GPS are OK
If someone see something that I should try, please tell me...
I had this issue once and it turned out to be the rom i was using, the usb charging should work fine from any computer and the light should come on. have you tried it with another cable on another machine?
It might be you have a faulty device and if its still under warranty reflash to original rom and send it to htc
First of all thank you a|ex for your interest.
As you suggest I tried a completely different ROM but with no success.
I also tried a shipped ROM (ah the return to WinMo 6.1, a time travel feeling) with no luck.
The Blackstone still doesn't no charge (no LED either) when power on.
May I ask for the procedure to follow to return a defective HD.
Thank you in advance.
You need to return device to stock rom and stock SPL
Follow guide at bottom of first post in this thread
frha said:
First of all thank you a|ex for your interest.
As you suggest I tried a completely different ROM but with no success.
I also tried a shipped ROM (ah the return to WinMo 6.1, a time travel feeling) with no luck.
The Blackstone still doesn't no charge (no LED either) when power on.
May I ask for the procedure to follow to return a defective HD.
Thank you in advance.
Click to expand...
Click to collapse
Fallen Spartan said:
You need to return device to stock rom and stock SPL
Follow guide at bottom of first post in this thread
Click to expand...
Click to collapse
Thank you Fallen Spartan for this useful link. It's already raise an issue for me. It will be hard to flash a stock SPL like described as I cannot use USB for sync.
I think I will first reinstall a Stock Rom thru SDcard and then install a Stock SPL via SDcard. I'll only do that If I received positive feedback from htc center.
Solved!
I had to send it back to HTC.
They change the Motherboard.
thanks all for your help

Categories

Resources