Related
Hello,
I'm currently trying to get a second hand I-Mate syncing with ActiveSync using a USB cradle. Everything else works fine, with the exception of a USB sync. When my I-Mate cradle is plugged in via USB, and the powered-on I-Mate is placed in the cradle, a Windows device message appears stating "USB Device Not Recognized". This happened with another I-Mate I was able to try and on multiple computers with multiple cradles. I'm quite baffled. I've tried verstions 3.7, 3.8 and 4.0 of ActiveSync.
I would really like to get the USB cradle working so I can try WM2005 and not have to xfer software to the I-Mate over my GRPS connection
Thanks in advance.
-Chris.
Hi Chris.
That certainly is odd since you've tried multiple ActiveSync versions on multiple PCs with multiple i-Mates!
What OS are the PCs running?
Normally when you first connect the i-mate via the cradle after installing ActiveSync, XP will launch the Add Hardware Wizard, which should find the drivers as ActiveSync installs them.
I have heard that reverting from ActiveSync 4 to 3.x can cause problems, but if you started with 3.7 & worked up from there, that isn't your issue.
Can you launch ActiveSync manually via Start - All Programs etc.?
Perhaps check the XP driver-signing policy - maybe it's stopping the driver from installing. I'd normally suggest trying a different USB port, but trying another PC covers that one .
Good luck - I know this one would annoy the hell out of me too!
Hi Chris.
That certainly is odd since you've tried multiple ActiveSync versions on multiple PCs with multiple i-Mates!
What OS are the PCs running?
Normally when you first connect the i-mate via the cradle after installing ActiveSync, XP will launch the Add Hardware Wizard, which should find the drivers as ActiveSync installs them.
I have heard that reverting from ActiveSync 4 to 3.x can cause problems, but if you started with 3.7 & worked up from there, that isn't your issue.
Can you launch ActiveSync manually via Start - All Programs etc.?
Perhaps check the XP driver-signing policy - maybe it's stopping the driver from installing. I'd normally suggest trying a different USB port, but trying another PC covers that one .
Good luck - I know this one would annoy the hell out of me too!
The PCs that I've tried have been running XP. My work machine SP1 while my home machine SP2.
I tried disabling the windows firewall in SP2 to no avail. The two other units I tried were in various states of order so that could be contributing to the issue.
The touchscreen is unresponsive on one while the other is stuck showing serial information (both issues I've found out how to resolve reading this forum, that'll make 2 more functional I-Mates!)
I have since completley removed ActiveSync from my PC at home. When I place my I-Mate into the cradle, no windows device messages appear and when I go into the device manager the I-Mate isn't even seen anymore.
I might just cut my losses and go cough up $40 for a usb bluetooth adapter for the desktop and sync that way. I'd rather not do this as I don't believe I can upgrade the ROM via bluetooth, and I'd very much like to throw WM2005 on one of these puppies, providing I can even get that far.
Ok, so a good majority will probably hate me after this.
My sync problem was caused by me not using a 5v power adapter. Yes, it was that simple. My power adapter looks like some kind of alien as it's being converted with 3 devices to conform to standard 110v north american AC. It was purchased for European users originally.
BUT, here's my saving grace. The I-Mate I was playing with won't sync via USB, it will do bluetooth and even serial but not usb???
Even more annoying is the unit I'm now using has an annoying issue with the touchscreen. If I receive a call or take care of any other incoming data activity, the screen freezes. I will not be able to use the touch screen until the battery is taken out. Very annoying, to the point I'm using the bluetooth unit. It's got the latest firmwares of the units (1.72wwe, 1.14 radio, 1337.38 for g (general?) bluetooth unit has 1,66wwe, 1.10 radio and 1337.2x for g) ...haha, sorry I thought that one was awesome and very fitting for a faulty device... just not the right number for a release...
I can't seem to connect my qtek9000 device to my IBM notebook via USB, well not exactly everything else works except Active sync ... are there any known limitations to this type of connection..
I also had some occasional connection issues with original ROM and Activesync 4.1. The following method worked fine for me:
- Upgrade to Activesync 4.1 if you haven't done so already.
- Unplug the Qtek and turn it off using the power button. Connect the USB cable. The Qtek should power on automatically and Activesync will detect it.
But anyway - I suggest you to upgrade to the latest Qtek ROM (UNI_QTEK_13077_176_10900_WWE_Ship.exe). I have no connection issues with the new ROM.
Does this ROM Update apply to the Qtek 9000 as sold by Mobitel d.d. in Slovenia..
Sure! The original Qtek ROM, which you are using now is UNI_Qtek_WWE_11364_151_10300_Ship.exe, so you can revert back at any time. You will only have to reenter GPRS & MMS settings, which is not a big deal. PM me, if you need the settings.
Until the HTC (QTEK) decided to publish the Official Upgrade I was running I-MATE JASJAR AKU2 ROM, without any problems whatsoever.
usb connection
Have you seen cardexport? A great little utility to make the sd card on your exec look like an external drive on your pc. Not a substitute for activesync but infinitely faster and more reliable method for file transfers to/from exec/pc. You can find it here:
http://www.softick.com/pocket-pc/cardexport2/
Have you seen cardexport?
I think that much better and cheapeer ( because is free) is WM5torage.
Now you can find super soft for your Universal - "the most expensive card reader on the world"
Hi Guys,
New to the ppc scene, so please be gentle!
I've had a search through the forum, and can't find the answer to my problem, so please help me, if you can.
I have just been given an imate jam by my dad, his old work phone. It hasn't been used for approximately 6 months, so I had to charge the battery (and back up battery) to get it up and running.
Now I've got it charged up and switched on I've encountered a problem:
When I connect my Jam to my PC (XP Pro) it lights up the charge LED but then nothing, no installing drivers or anything. When I start activesync it doesn't see the Jam, when I go to device manager on my pc it's not there.
The Jam has also reset itself a few times, so I was thinking I should upgrade/reflash the software - but I can't do that when the PC doesn;t see the Jam.
Have I missed something, done something stupid or is the Jam knackered? Any help would me muchos appreciated
Many thanks in advance.
My device is an imate jam, details below:
ROM Version: 1.03.00 WWE
ROM Date: 11/01/04
Radio Version: 1.01.00
Protocol Version: 1337.38
Ext ROM Version: 1.03.163 WWE
Not sure if this helps anyone help me with my problem, but thought the more information the better!
Thanks in advance for you help
Check your connection settings in ActiveSync.
Ok, I've just tried the settings you suggested, though for some reason I can only select COM4?? I'm using activesync version 4.1.4841.0
When I try and connect I get the error shown in the attached image
Although some have had luck with AS4.x, others as well as myself have experienced that it doesn't work very well with the Magician. Use AS3.8 and it works flawlessly.
ok, I've changed to activesync v3.8 and still no joy - it just goes in circles looking for the device on COM4
I'm showing:
COM1 Not Installed
COM2 Not Installed
COM4 Available
Infrared Port Not Installed
USB USB is Available
This is driving me crazy!!
Normally when the magician is plugged in to the usb port, windows should recognize this and go through the usual driver installation procedure. If not disconnect the magician, switch off all settings in AS and reboot your PC. After the PC has booted and you logged-in, connect the magician to a different usb port. If the windows plug+play install routine does not appear, go to control panel and add the device manually. Once the device is added, then put back your settings in AS.
ok, 2 reboots later!!
when I connect it (on a different port) all that happens is the LED goes Orange to indicate that its charging - no drivers are installed.
When I go to Add Hardware it can't find the Jam (tried changing the port) and if I go to device manager its not there (not even with a ! Warning next to it).
I'm now trying to add it from a list, but I can't find imate or HTC in the list of manufacturers.
I'm totally stumped, this is insane!
Any more ideas?
Try hard resetting the magician then check AS settings in the magician also.
I've done a hard reset and rebooted my pc again, still nothing, even when I try and add it manually.
I've even tried connecting in bootloader mode, but that won't work either!
Could it be a hardware fault? Or more likely a software thing?
Not being recognised
Hi
I had the same problem today, it turned out to be a faulty cable(brand new spare). I used a different cable and all is good.
:wink:
I've now tried 3 different cables, 2 latops and a desktop PC and am having the same problem no matter what - I reckon my Jam's screwed up somehow!
Take a look on the connector, try to clean it(with alcohol preferably and with battery out of jam). You have to have AS installed before you connect the jam to pc for the first time, otherwise it will cause problems. Did you try BT connection to active sync? Did it work? Did your dad experience these problems too?
Ok, there's definately a problem with my device.
I can pair it up via BT and transfer files etc, but as soon as I connect with Activesync I get the same error message as I posted earlier in this thread.
I've tried cleaning the mini-usb port (battery out) with alcohol, still no joy.
Spoke to my dad, says he never used activesync, just used it as a phone and a sat nav, nothing more.........
Starting to get really wound up by this now. Unless anyone has any other ideas (dropping it from a great height??!!) I think I'm gonna have to send it to a repair centre for them to have a look at it
i had an intermittent problem like this wherw windows would say a USB device connected to the system was malfunctioning etc..
It cleared up after a while donno why... when uve connected the JAM, wiggle the connector around a bit and see if anything happens....
The message you get is not necesarilly caused by faulty device, I got that message many times before I was able to properly configure my active sync over BT.
the cable supplied with imate jam looks like a normal mini usb cable but its not.
its different then the mini usb cable. You cant use a mini usb cable (from ur camera,card reader etc.) with your imate jam.
Once I used my camera mini usb cable with imate jam and i got the same error which omhaigh is having. Netither Windows recognize my imate jam nor activesync. I plugged in my imate jam cable and it was all good again.
In short, you need cable supplied with imate jam to connect it with pc.
The Magician's USB cable is a standard one. I've been using various USB cables on my laptop. home desktop, and office PC without any problems.
yeah, it is completley standard, ive used 5 different cables and all work,
I've now tried a whole host of PC's and Laptops at work, using several mini usb cable and bluetooth (both built in and dongle on different machines) following the advice above and in the BT active sync thread.
No matter what I do (including cleaning the ports with alcohol etc) I get no joy what so ever, and always end up with the same result!!
I've read that connecting the device to a pc before installing activesync can cause problems.......I'm starting to think that perhaps my dad's done that and either can't remember or is too embarrassed to admit it! Is there a fix if this is what has happened?
I'm guessing its gonna have to go to a repair centre
hello all,
Is it possible to have av-out on my wm5 device?
I have an mini usb with on the other end a red and a yellow plug.
i've already tried to connect but it just doesn't work.
is there any application i can use so i can connect to my tv via av???
My phone is a orange M600 aka prophet with latest dopod rom.
TIA
rebelish, that is just not going to work. I mean that is not a PC usb port. First its a mini-usb, second its not got all the WinXP functions which enable it to be so.
What might be a solution is to have a SD Socket AV-out (haven't seen any), or even try it through wifi... There is a program (forgot the name) which transfers the picture to the PC through wifi, but probably does not work for video.
Cheers.
A.) most PDA USB ports are slave, meaning normal addons will not work on them
B.) there are indeed SDIO cards that provide a VGA/AV output
The only pda I've seen with video out is the Dell x51v. I'm guessing it's a fair custom job, using more than just a mini-usb cable.
ok Thanks everybody for all the clear answers.
I do think it's a shame that we don't have that function already in our pocketpc's but than again we can't have it all.
I think i'am going for the bluetooth pal adaptor now because with that one can do the job wireless and i can show my 2Mega pixel pics on my tv screen.
everybody thanx again
cheers
i have a t-mobile mda wizard and every time i plug it in to my pc it says device not recognized but it charges and everything... i just bout a new cradle and everything but no dice on it connecting and im running windows xp... help will be appreciated
Right click the activesync button in your toolbar and open connection setting. Click connect device. It will try to connect. If it won't, the best thing is to go thru the help thing. Do you have a custom rom?
active sync do not work
Hi there, i heard some days ago (a friend who ask me for help, unloking wizard to change ROM) and his WIZARD was not able to get recognized by PC it was a bad contact between USB conectors and cable, so he sent phone to repairs and then he was able to sync and then to migrate from WM5 to WM6.1
perhaps is a connectors trouble.....
What version of Activesync are you using? If it's 4.5, you should be good to go. I have seen problems with older versions.
Also, check Activesync on your phone. Make sure you don't already have two accounts created, because that's the limit on your phone.
If not, try different USB Cables and different USB ports (or test those things on a different device with microUSB connection) before assuming the connector on the phone is bad.
as far as i know the phone is completely factory no upgrades or anything i tried to do the connect thing thru active sync where it looks for my phone still no connection and i bought a new cradle and usb cords all together and it still doesn't work...