Related
Hi all.
Need some help really bad. Tried to upgrade my magician (s100) to ROM 1.11.133WWE from qtek.se.
Did exactly as it said I had to but as soon as I started the upgrading my magician went all dead and black and the install shield wizard went down. The only thing left on the computer screen is a box that says: "checking the information on your device... please wait...
Please dont disconnect your device from your PC until the update is completed".
So what do I do?!?!
Am desperate to get my device working again!
Please please help me!
I'm really sorry to here this ... anyway..
As far as I know.. u have my to disconnect ur PPC from the USB cable, then restart PC, u should continue to upgrade after u PC restarts..
u may also try to change the port of the USB cable as well...
this may work on Win XP, I don't know anything about other OS..
I'm not sure about this since I did not face this problem b4..but this solution was reported in another forum ( and maybe here )
I hope this will help...and maybe someone else could give u more INFO...
cheers
Alive!
Got it working!
Did a couple of reboots and that made the trick...
Now, my only problem is that I cant seem to restore my backup-files
Does anyone know where I can download the free program o2plus that I had earlier? Can´t find it anywhere. Loved that thing...
Thanx!
I believe it is better if u do a new fresh installation of everything instead of making a restoration
many users reported problems when restoring after an upgrade...
mostly, ur device will become very slow ....
I attemted to flash my Kjam to WM6 & it went dead. It wont start at all. Kjam Service centre says there is a problem in the mother board and it needs to be replaced for $ 300+........now if flash fails...the ROM must have gone corrupt , what has it to do with the motherboard ?
can anyone throw light on whats the real thing ?
Deven.
take out the battery for hours then re-install it. try to boot in bootloader mode first(3 colors). If it work, it's the time to re-flash the right rom now!
When you start the device up what happens?
Same Problem accured for me!!!!!!!
I installeda new rom and my device didn't power on after that.
What should i do now?
afghahi said:
I installeda new rom and my device didn't power on after that.
What should i do now?
Click to expand...
Click to collapse
Nobody here is providing any details so everything is going to be just a guess. If either of these phones were a G4 and you flashed a rom that tried to update the IPL/SPL then its very likely you have bricked your device. But again, with no information about what rom you were trying to flash, what your IPL/SPL were beforehand, or details about what it means that it won't turn on, everything is just a guess...
Bricked Kjam
its comletely dead.....i had disconnected the battery for a couple of days then connected it but it wont start....i checked the battery using multimeter it is fully charged....neither does it power ON when connected to mains...It doesnt get detected when connected to the USB port..thats obvious since it is not powering up...so cant flash it again.. now m in a fix as to whether to spend another fortune after this sweetheart or keep it in a showcase ....
Deven
( a bricked KJam )
If nothing lights up that looks pretty terminal. :-(
Maybe you could buy a broken Wizard with a working motherboard? Alternatively maybe sell off your mostly working Wizard on this forum to raise money to buy a new device?
Sorry if you can't get it going. :-(
Hi i am new here and my hermes brick, no gsm, and splash on windows screen and i can not in in Kitl mode
I send my phone to reapair center and there want change the mainboard.
Can annybody help me? to get new mainboard?
I sent a bricked Hermes back for repair a couple of months ago and the motherboard was going to be more than 6 weeks from HTC, so I think it'll be difficult to get one from anywhere else.
But, before spending loads of cash on a new board, try posting here http://forum.xda-developers.com/showthread.php?t=286755 and someone may be able to help you fix the phone.
Give as much info as possible about your brick:
Which OS version.
IPL/SPL
Which radio before NO GSM message.
Is it hard SPL
Can you connect to PC and try to upgrade. If so, what is the error message.
Are you Super CID.
How did you brick the phone (eg power loss during upgrade etc).
There is a chance that someone can help - and it costs a whole pile less than a new motherboard (even if you pay the elf ).
Good luck.
closer66 said:
Hi i am new here and my hermes brick, no gsm, and splash on windows screen and i can not in in Kitl mode
I send my phone to reapair center and there want change the mainboard.
Can annybody help me? to get new mainboard?
Click to expand...
Click to collapse
I had befor orginal o2 rom germany, and have spl 1.09, and i want flash t- mobile hungary rom english rom, everythink runs fine flash without anyproblems. After finish phone restart and show no gsm and hang on windos mobile screen.
when my phone connect to pc in splash screen than activsync can not find. When i start in bootloader screen. 3 colors. yes than i can connect. but flashing any other rom not possible. i try all roms always same message.
My phone dont have anny CID annymore befor was super cid. But now i can not find anny cid
Hello people ...
not much to say ...
i think i bricked my phone .... =(
i installed one of the ROM downloaded from here ...
and it brick my device ...
what should i do ? :`(
it says on the screen :
" Your OS ROM isn't customized for you hardware.
Please refresh the proper ROM code or contact the service center. " ((
p.s. i cant install other ROM
couse it cant see the usb (((
i got the problem solved =)
guess it came from it self couse i was nurvios )))
i entered the hard boot menu pressed the UP (volume) button and then pressed 2 time i think the up(coluve) and down(volume) then it not entered the boot option but connected the USB ...
i installed other ROM and its working fine again ... )))))
so far I have seen 1000 people on xda developers that assume to have bricked their phone...and probably 1 out of 1000 has truly done something stupid to brick his phone.
[email protected] said:
so far I have seen 1000 people on xda developers that assume to have bricked their phone...and probably 1 out of 1000 has truly done something stupid to brick his phone.
Click to expand...
Click to collapse
And then there are the 999 who think they have done something clever, but still bricked their phone...
gladly im not one othe 1\1000 people that done it =)
i had my luck on this one =)
i guess i was celebrated too early...
i tryed to delete the HSPL
by the video tut ... ( yeh yeh ... what can be more easier )
well ...
it says to get a stock rom ( i did it )
it say to put it on the SD after formating it to 32 bit ( i did it )
then hard boot ... ( i did it )
power button ...
and ........... puff ...
now i get: ( On boot ):
PB81100 HX-BC
SPL-1.42.0000 XE
microP(LED) 0x05
microP(TOUCH) 0x03
Upgrage ROM code error
Please try again ...
WHAT IS THAT ? :`(
dose it means i brick it ?
(p.s.)
Tryed to install the HSPL again ...
the install is successfull. ... but no change on the device ...
you have used the wrong rom.
you must use the correct rom that was on the phone when you got it.
Or the correct region. In doubt, just enter your phone's serial number on the HTC download page (here for 1.66) to make sure you get the correct official rom.
Then extract it, put the nbh on your card, etc.
" Sorry, this software download is not suitable for your device. "
hhmm .... i had the hong kong rom originaly ...
maybe it means i have to download it from an hong kong htc site ?
yes....choose the hk site
Are you solved the problem?
How?
I have a similar problem.
I have the same screen at boot, but when I try load anything my device as stuck in progress bar (0%) even for shipped rom’s…
This happens when I try load a shipped rom from SD. Before that I have loaded several cocked rom’s from SD without problem.
the fix...
hold volume up and down together and insert the USB cable then run a different or a good ROM
Bricked friends hd2!!!?!?
PLEASE HELP... I was trying to install android throught NAND on my friends hd2,, in the process of flashing the ROM via Magdalr or whatever.. it froze so i pulled the battery.... and it doesn't turn on. I've pulled the battery on my other friends HD2 so im confused as to why this one in particular does not turn on! PLEASE HELP!!! SHE'LL KILL ME IF SHE FINDS OUT!!!
EDIT: PHEW i figured it out... but im having trouble installing these ROMs
Did i brick my phone??
So my brother was trying to do who knows what to my hd2 and now the hd2 powers on and it says "stick together" (its a t-mobile hd2) and it just stays on that screen.. I'm not the most tech savvy person so bare with me... usually below where it says "stick together" it would show a bunch of numbers and codes and after a few seconds it would load windows mobile and the phone would work fine. However, mine just stays on the stick together and theres no more of those numbers and codes on the bottom.
Did he just brick my phone? And if he did... HOW THE HECK DO I FIX THIS???
HELP :*( i need to use my phone!!
Thanks
Heh I'm in the process of doing my very first flash to get a full install of Andriod 2.2 on my HD2, once I find out a specific answer I've been looking for I'm gonna start the process
HD2 brick
I just bricked my HD2 (USA T-Mous). I tryied update RADIO when was progress on PC 100% in PDA 96% and freezed. I just pulled battery and phone is bricked. When I connect to PC via USB, i can listen twice short plug sound and this is all. No bootloader, nothing. Any reason? Thanks
Did you try to turn on your mobile pushing "vol down" to load usb mode ?
After that, you can flash an official rom.
That "saves" my Leo...
NarkotiQUE said:
I tryied update RADIO
Click to expand...
Click to collapse
if the radio had 51 in the version (example 2.07.51.xx) then it is a brick, dead, gone.
NarkotiQUE said:
I just bricked my HD2 (USA T-Mous). I tryied update RADIO when was progress on PC 100% in PDA 96% and freezed. I just pulled battery and phone is bricked. When I connect to PC via USB, i can listen twice short plug sound and this is all. No bootloader, nothing. Any reason? Thanks
Click to expand...
Click to collapse
Did you have any luck? Does your device have HSPL? Let me know if you still need assistance.
xtntx said:
Hello people ...
not much to say ...
i think i bricked my phone .... =(
i installed one of the ROM downloaded from here ...
and it brick my device ...
what should i do ? :`(
it says on the screen :
" Your OS ROM isn't customized for you hardware.
Please refresh the proper ROM code or contact the service center. " ((
p.s. i cant install other ROM
couse it cant see the usb (((
Click to expand...
Click to collapse
hi i'm looking for a motherboard htc hd2 bricked? can you sell yours?
My name is carlos and im new in the forum.
This is my problem. I have an HTC Imagio. I tryied to update it but i fail because my phone wont turn on again. I dont know what can i do because I new in the htc world and I dont know how can I start.
Please heeeeeeelpppppp meeeeeeeeeeeeeeee
when yoy say "fail" what exactly happen....???
The phone wont turn on again T_T
You're not giving a very good explanation, did you attempt boot loader mode? anything else? at the present moment, you're just taking up thread space..
The boot loader mode is the hard reset??? or what is it?? The phone doenst enter on the hard reset (color screen with 3 options)
Moved as this is not ROM Development
Sorry about that, anyone know how i can fix it????
Hi i have a imagio dead. No bootloader load (someone wrote a blackstone hspl) and broke it .. the only thing when i connect on usb it is found as a qualcomm msm smthing. no drivers for this.. looked all over, xda, google. i found some jtag methods... I wrote a Intelpxa for a rw6815 with jmmflaser... but befor trying a jtag method, and/or try to sell it for components, i want to give it another try. Does enyone know how at least connect to mtty(to write wia usb the bl), or write a bl (any) wia usb?
Imagio Bricked
No USB way...
Unbrick a phone just can be made with JTAG tools... See jtagbox.com/riff-jtag-box-owners-unbrick-your-phone/shops-unbrick-bricked-phone-riff-box-owners-list
Hello everyone ... this is my first post on the forum I'm a reprimand in my assistance, a residue in Brazil and a customer trou Imagio HTC unlock the verizon and I just noticed that no longer seems to me he is the one CDMA XV6975 which blotted out and not turned over, but do not have IMEI MEID DEC and HEX as well ... riff bought a box to try and repair it could make you turn it on, no longer leaves the HTC logo and is vibrating, already tried the hard reset recovery mode and nothing continues to vibrate, not boot tried one more rom's not leave 0%. Can anyone help me with this device, because the customer does not come out of my foot.
Thanks to all.
Htc imagio bricked
hello guys, i really need help from u. i bricked my imagio this evening and right now it wont turn on so i don't know if u guys can hlp me with any software to recover it.
I will be very happy to c my imagio is breathing.
thanks for your help may God bless you all.