Database Users

USB port no longer working on cingular 8125.

My cingular 8125 USB port was working just fine unti I rebooted the 8125while it was runing wizardbackup uitility b/c I did not have the min sd card to back it up( my....). So, now the usb port is no longer working. Activesyn can't connect but the device is charging when I have the device connected to a labtop via usb cable. I hav tried:
- Hard reset & soft reset on the device
- Reinstall Activesysn
- Activsycn is set as usb in the device
thanks much.
w

Confirm your hardreset(many doesn't realised what they did is just softreset)
Try different cable different PC.
Use Wm5torage to test if you want.
Try activesync via IR/bluetooth.

I have tried all of these and none of these response (bluetooth, iR, different pc, etc..) . Can I reflash my ROM from mini SD.
thanks,
hn

weester said:
I have tried all of these and none of these response (bluetooth, iR, different pc, etc..) . Can I reflash my ROM from mini SD.
thanks,
hn
Click to expand...
Click to collapse
Only if its CID Unlocked

How can I unlock CID if I can't get to USB, ir/bluetooth connection via activesyn. Can I do it via mini SD? if so,please show me how.
thanks,
hn

Can you get into bootloader mode (The 3 colorbars)??? If yes, plug in the usb and see if it reads in the lower corner (it will say usb). If yes, you should be able to re-flash your phone, and from what you wrote, it sounds as if the usb will read...however, if your usb port is damaged, you may have a bigger issue to deal with.
For more detailed info, click the linky in my siggy. It is the most complete thread I know of about saving a wizard from death.
Most wizards can be saved...mine wasn't but mine was severely damaged...that being said, the thread linked below gives great info on various methods.
Also, if it is an active-sync issue, it can usually be corrected.
Read the thread, see if any of it helps, then report back if you need more help.

I can get into bootloader mode (The 3 colorbars) I then plug the usb to my pc and usb see it for 2 seconds and it disappears saying "USB is not recognized". When I try to flash the "RUU_wizard_225111_22511102_02252_CWS_wwe" downloaded from htcwizard website and i get " ERROR [260]: UPDATE ERROR".

Stuck on bootloader screen

Hi all, I am a noobie at this and I think I have done somrthing wrong somewhere. I have a XDA Exec and I atempted to load Bootloader 1.01 Update, the problem I have is with the USB pluged into the computer the only thing on the XDA screen is USB V1.00, when I unplug the USB cable the screen say's serial v1.00. Cant seem to get it to connect to pc or anything else as a matter of fact Could someone please Help meeee.

Mogul goes into bootloader on reset?

I've got a couple of strange problems with my mogul - anytime I need to reset it, it goes into bootloader (both soft and hard resets). However, If I connect it via USB to my pc, the reset will work.
The second problem is a USB connection to the PC only charges the mogul, the pc doesnt actually recognize it (it doesnt give the windows device connection sound)- so i cant flash it to try and solve the first problem. It also isn't recognized when I plug it into USB while in bootloader mode, I just get the "Unrecognized USB device" error in XP and Vista on two different computers. It might be worth noting that I get the USB device connection sound when i reboot the phone, then the "unrecognized usb device" error, then the disconnect sound as the boot finishes and windows mobile loads. I've tested the cable with other devices and tried multipile cables, so I dont think thats the problem
Any suggestions?

Ok, I got the USB working but nothing will keep it from going into bootloader on reset if it isnt connected to my pc. I've reflashed and hard reset to no avail. no one has any suggestions?

I had this same problem w/ my fiance's mogul... as far as i know there's nothing you can do but take it to sprint and get a replacement... and just as an fyi.... i never modded her phone... it was completely stock!

My Herm100 does not connect to pc via USB

Good day,
Here is my problem, My Herm100 does not connect to pc via USB! It used to connect easily but about 4 days ago it stopped i have replaced 4 cables but still unable to connect! The cell charges when i connect to usb but does not connects to activesyn nor shows that anything has been attached to pc! I'm using activesyn 4.5 everything is same i have not changed / installed anything new on PC or mobile! the os i'm using is Win-xp (Service Pack 2). i have changed 4 cables and tested it on 3 PCs and 1 laptop! Please help me i will be very thankful to you...

Just for the sake of a dumb question, have you rebooted the phone?
I have had a couple instances of my device not connecting till I reboot it.

Yes, i have rebooted it a lot of time! even putted it in the boot loader but didnot did anything. after putting it in the boot loader i just restarted it. It charges with usb cable but does not connect.

You could try opening usb to pc and either check or uncheck the checkbox 'Enable advanced network functionality'
If that doesn't work, then I would grab pim backup, to back up all of your contacts and try a hard reset.
If it still doesn't connect, then I would guess something went wrong with the usb port on the device.

X2 in Bootloader Mode not recognized!

I have now my X2, generic_SG. It gets into bootloader moder easy but then it is not recognized my the pc or SEUS.
When I got it, and during drivers where installed upon connection the usb, it was recognized. But now, no more. So I cannot use the SEUS service even though its in bootloader mode!
I only read about people not able to get into bootloader mode, but in my case, very strange. Any help?

I had the same problem.I just change the usb cable and put in directly to pc and now is everthing ok.

What do you mean 'direct in pc'? One had to plug it always in the pc !?!
And I am using the SE provided cable. Perhaps I will try a different one but I don't think its the cable as it work fine sync'in with pc. Just in bootloader mode its a no go.
Tried today with another computer. Both have Win7 Ultimate.
Also tried 'another' cable / cables but same issue remains!