I have now my X2, generic_SG. It gets into bootloader moder easy but then it is not recognized my the pc or SEUS.
When I got it, and during drivers where installed upon connection the usb, it was recognized. But now, no more. So I cannot use the SEUS service even though its in bootloader mode!
I only read about people not able to get into bootloader mode, but in my case, very strange. Any help?
I had the same problem.I just change the usb cable and put in directly to pc and now is everthing ok.
What do you mean 'direct in pc'? One had to plug it always in the pc !?!
And I am using the SE provided cable. Perhaps I will try a different one but I don't think its the cable as it work fine sync'in with pc. Just in bootloader mode its a no go.
Tried today with another computer. Both have Win7 Ultimate.
Also tried 'another' cable / cables but same issue remains!
Related
My cingular 8125 USB port was working just fine unti I rebooted the 8125while it was runing wizardbackup uitility b/c I did not have the min sd card to back it up( my....). So, now the usb port is no longer working. Activesyn can't connect but the device is charging when I have the device connected to a labtop via usb cable. I hav tried:
- Hard reset & soft reset on the device
- Reinstall Activesysn
- Activsycn is set as usb in the device
thanks much.
w
Confirm your hardreset(many doesn't realised what they did is just softreset)
Try different cable different PC.
Use Wm5torage to test if you want.
Try activesync via IR/bluetooth.
I have tried all of these and none of these response (bluetooth, iR, different pc, etc..) . Can I reflash my ROM from mini SD.
thanks,
hn
weester said:
I have tried all of these and none of these response (bluetooth, iR, different pc, etc..) . Can I reflash my ROM from mini SD.
thanks,
hn
Click to expand...
Click to collapse
Only if its CID Unlocked
How can I unlock CID if I can't get to USB, ir/bluetooth connection via activesyn. Can I do it via mini SD? if so,please show me how.
thanks,
hn
Can you get into bootloader mode (The 3 colorbars)??? If yes, plug in the usb and see if it reads in the lower corner (it will say usb). If yes, you should be able to re-flash your phone, and from what you wrote, it sounds as if the usb will read...however, if your usb port is damaged, you may have a bigger issue to deal with.
For more detailed info, click the linky in my siggy. It is the most complete thread I know of about saving a wizard from death.
Most wizards can be saved...mine wasn't but mine was severely damaged...that being said, the thread linked below gives great info on various methods.
Also, if it is an active-sync issue, it can usually be corrected.
Read the thread, see if any of it helps, then report back if you need more help.
I can get into bootloader mode (The 3 colorbars) I then plug the usb to my pc and usb see it for 2 seconds and it disappears saying "USB is not recognized". When I try to flash the "RUU_wizard_225111_22511102_02252_CWS_wwe" downloaded from htcwizard website and i get " ERROR [260]: UPDATE ERROR".
I've got a couple of strange problems with my mogul - anytime I need to reset it, it goes into bootloader (both soft and hard resets). However, If I connect it via USB to my pc, the reset will work.
The second problem is a USB connection to the PC only charges the mogul, the pc doesnt actually recognize it (it doesnt give the windows device connection sound)- so i cant flash it to try and solve the first problem. It also isn't recognized when I plug it into USB while in bootloader mode, I just get the "Unrecognized USB device" error in XP and Vista on two different computers. It might be worth noting that I get the USB device connection sound when i reboot the phone, then the "unrecognized usb device" error, then the disconnect sound as the boot finishes and windows mobile loads. I've tested the cable with other devices and tried multipile cables, so I dont think thats the problem
Any suggestions?
Ok, I got the USB working but nothing will keep it from going into bootloader on reset if it isnt connected to my pc. I've reflashed and hard reset to no avail. no one has any suggestions?
I had this same problem w/ my fiance's mogul... as far as i know there's nothing you can do but take it to sprint and get a replacement... and just as an fyi.... i never modded her phone... it was completely stock!
Hi guys ,my problem is that when I connect my phone via USB cable at first there is no problem, data transfer , windows mobile device center, everything is OK. But when I want to flash the phone pressing vol-down + switch on/off keys the phone is not connected to the PC. And I can't flash it. Also the phone wouldn't like charge trough the charger ,only with the data cable. Is it possible to have any liaison between the problem with charging with charger and no-connection when try to flash.
Also my phone was to the service for touch-screen change ,is it possible the technician make any mistake ? Cause I think that if he make a mistake with the connector nothing gonna work ,but it works at different situations.
Regards!
check to be sure USB SYNC driver installed correctly and also try a different usb cable.
I'll try but there is no logic ,the cable works when charge the phone, works when is connected to device manager but doesn't works when flashing ?
exactly. the device requires different drivers.
1. there is internet sharing and disk mode (which works with all computers, because those drivers are in the operating system)
2. then there is one driver for syncing
3. and another one for flashing
it is not the same kind of data transfer, which is why you need a different driver. but the thread "[tut] updating htc sync drivers" should cover all your windows vista/7 driver needs and a tutorial on how to install them, which in case of a x64 system can be fairly complicated.
if you already have hspl installed (which you can determine by entering bootloader mode and looking whether it says 1.56Olinex), you can also flash using the sd car method. put a rom of your choice on the sd card, name in BLACIMG.nbh and enter bootloader mode, you will be presented with options to flash the rom.
Ok, but in instructions at the thread you give me is written that I have to start making the steps after I see "USB" on the flashing screen. But I don't see it, it's only "Serial". And now what ? I know that if on the screen i written "USB" the phone and the computer are connected and there is no problem to flash ,but now what ?
well, before you start, put your device into bootloader mode. it will show "serial", then connect it to the pc. test your connection using mtty 1.42 (you'll find several download options here in the forum).
the connection settings for mtty are USB 115200-8-1-No-NONE-None
if it works, connect and press enter, the command shell should show USB> then.
if usb is not present in the connection settings, your connection is not established yet. proceed with the tutorial then. during the entire procedure, the device should remain connected to the pc in bootloader mode, so you install the driver for the right device state.
Hello,
I've problem something like this. Few months ago when i was conecting my phone to computer was everything OK, activesync, disk drive, but now nothing, just charging the phone. I've tryed everything in USB to pc zone, but nothing. When i'm going to bootloader it's writen serial. What can be here?
since you already tried all the different connection methods and even bootloader mode does not connect, there are hardly any options left, where the trouble could be:
- the usb port on the blackstone
- the usb port on the pc
- the cable
you can try another port on the pc (or even better, another pc altogether) and/or another cable, like from a digital camera, an external hdd... (many devices have mini usb cables, you should be able to use either one of those)
Hello folks,
Ive written beforehand in here asking for a little issue I had with my milestone 2 (Assuming a dead usb port and a bootloop)
anyway I got replaced the USB connector, but My phone wont show up on RSD lite... No matter what version I use (tried everything from 4.9 to the latest, nor the drivers.) Im on win 7 ultimate x64, but tried on ubuntu, win xp and win 7x32 having no success.
The phone WONT charge over usb, even with it's usb port replaced.
Teh phone will enter stock recovery, and bootloader mode ( it´s on 07.12)
The phone will also recognize it is "connected" on bootloader (It reads USB Connected OK to program), but the PC wont recognize it.
any suggestions???
may I have to flash it with a "box"??
donlloreda said:
Hello folks,
Ive written beforehand in here asking for a little issue I had with my milestone 2 (Assuming a dead usb port and a bootloop)
anyway I got replaced the USB connector, but My phone wont show up on RSD lite... No matter what version I use (tried everything from 4.9 to the latest, nor the drivers.) Im on win 7 ultimate x64, but tried on ubuntu, win xp and win 7x32 having no success.
The phone WONT charge over usb, even with it's usb port replaced.
Teh phone will enter stock recovery, and bootloader mode ( it´s on 07.12)
The phone will also recognize it is "connected" on bootloader (It reads USB Connected OK to program), but the PC wont recognize it.
any suggestions???
may I have to flash it with a "box"??
Click to expand...
Click to collapse
Either your USB port got replaced badly, or you don't have the drivers: http://www.motorola.com/staticfiles/Support/Experiences/Global_Drivers/USB_Drivers_bit_4.7.1.zip
Try a different cable, diferent port, different computer...
hello
i have a problem with my g928f
my issue is that it can not be regognized by the windows
i have tried at my desktop with win 10 and at my laptop with windows 7 and at both says unknown device,
i have tried everything i know of
unistall everything from the pc regarding samsung drivers
install it again , nothing
install smart switch , nothing
install kies, nothing
run odin , not even see the phone at download mode
made factory reset from recovery , nothing
charge is working just fine both from pc and my wall charger
i tried mhl hdmi and nothing happened
tried just now otg cable with a usb drive , again nothing
just a week ago i was using it just fine with my pc
should i take it to a store to check my micro usb port??
noone??
today i replaced the screen with a new one witch had a new usb dock on it and the problem is still here
i can not connect it to any pc.
i cann't flash the stock rom because odin is not see it also
is it possible to be a rom problem????
i can't flash the stock one because of the usb issue
but i think i can download another lollipop rom to give it a try.
Have you made sure that it is set as MTP?
Setting - Storage - USB.
Check if the device gets connected in Fastboot mode. If it doesn't then it would be your USB.
sideload is not working either
usb is brand new and original.
is there a way to flash stock rom via recovery?