Database Users

Mogul goes into bootloader on reset?

I've got a couple of strange problems with my mogul - anytime I need to reset it, it goes into bootloader (both soft and hard resets). However, If I connect it via USB to my pc, the reset will work.
The second problem is a USB connection to the PC only charges the mogul, the pc doesnt actually recognize it (it doesnt give the windows device connection sound)- so i cant flash it to try and solve the first problem. It also isn't recognized when I plug it into USB while in bootloader mode, I just get the "Unrecognized USB device" error in XP and Vista on two different computers. It might be worth noting that I get the USB device connection sound when i reboot the phone, then the "unrecognized usb device" error, then the disconnect sound as the boot finishes and windows mobile loads. I've tested the cable with other devices and tried multipile cables, so I dont think thats the problem
Any suggestions?

Ok, I got the USB working but nothing will keep it from going into bootloader on reset if it isnt connected to my pc. I've reflashed and hard reset to no avail. no one has any suggestions?

I had this same problem w/ my fiance's mogul... as far as i know there's nothing you can do but take it to sprint and get a replacement... and just as an fyi.... i never modded her phone... it was completely stock!

USB device is not recognized error.

Hi all,
I'm experiencing the above problem. It started last week when I tried to reflash the firmware to a third party firmware. The unit could power up as normal, wifi, bluetooth all working fine but not the USB. I've tried installing a utility which switches the mode from RNDIS to USB but it still failed .. hard resetting the device does not help either. Is there a way that I could revive the USB connection? I couldn't sync my contact etc at the moment with my PC.
BTW, currently I'm on Onyx Jr. 4.1.2. I could not update to any firmware due to this and I don't have microSD to SD converter which I could use to copy the firmware to the microSD.
TA.

Disconnect sync cable. Reconnect to different usb port on computer. Right click ActiveSync in taskbar. Click connections. Make sure "Allow USB connections" is checked. If above fails, uninstall usb adapter in device manager, reboot computer. It'll reinstall with stock drivers after reboot.

It may happen due to faulty USB cable. Try and use another cable and on some other computer and check

I've tried all that I could think off including removing activesync and reinstalling it back. I've few miniUSB lying around and I've tested many of them but my notebook just did not want to recognized the htc touch. I've tried using those cables with my wife's tytnII and they worked .. could it be the hardware problem inside htc touch itself?

Tried with a new USB cable found in my newly bought GPS and if I reseat the cable properly, my notebook could recognised the htc touch. So I guess a new cable does help.. thanks all for the help.

My Herm100 does not connect to pc via USB

Good day,
Here is my problem, My Herm100 does not connect to pc via USB! It used to connect easily but about 4 days ago it stopped i have replaced 4 cables but still unable to connect! The cell charges when i connect to usb but does not connects to activesyn nor shows that anything has been attached to pc! I'm using activesyn 4.5 everything is same i have not changed / installed anything new on PC or mobile! the os i'm using is Win-xp (Service Pack 2). i have changed 4 cables and tested it on 3 PCs and 1 laptop! Please help me i will be very thankful to you...

Just for the sake of a dumb question, have you rebooted the phone?
I have had a couple instances of my device not connecting till I reboot it.

Yes, i have rebooted it a lot of time! even putted it in the boot loader but didnot did anything. after putting it in the boot loader i just restarted it. It charges with usb cable but does not connect.

You could try opening usb to pc and either check or uncheck the checkbox 'Enable advanced network functionality'
If that doesn't work, then I would grab pim backup, to back up all of your contacts and try a hard reset.
If it still doesn't connect, then I would guess something went wrong with the usb port on the device.

Problem with usb connection

Hi guys ,my problem is that when I connect my phone via USB cable at first there is no problem, data transfer , windows mobile device center, everything is OK. But when I want to flash the phone pressing vol-down + switch on/off keys the phone is not connected to the PC. And I can't flash it. Also the phone wouldn't like charge trough the charger ,only with the data cable. Is it possible to have any liaison between the problem with charging with charger and no-connection when try to flash.
Also my phone was to the service for touch-screen change ,is it possible the technician make any mistake ? Cause I think that if he make a mistake with the connector nothing gonna work ,but it works at different situations.
Regards!

check to be sure USB SYNC driver installed correctly and also try a different usb cable.

I'll try but there is no logic ,the cable works when charge the phone, works when is connected to device manager but doesn't works when flashing ?

exactly. the device requires different drivers.
1. there is internet sharing and disk mode (which works with all computers, because those drivers are in the operating system)
2. then there is one driver for syncing
3. and another one for flashing
it is not the same kind of data transfer, which is why you need a different driver. but the thread "[tut] updating htc sync drivers" should cover all your windows vista/7 driver needs and a tutorial on how to install them, which in case of a x64 system can be fairly complicated.
if you already have hspl installed (which you can determine by entering bootloader mode and looking whether it says 1.56Olinex), you can also flash using the sd car method. put a rom of your choice on the sd card, name in BLACIMG.nbh and enter bootloader mode, you will be presented with options to flash the rom.

Ok, but in instructions at the thread you give me is written that I have to start making the steps after I see "USB" on the flashing screen. But I don't see it, it's only "Serial". And now what ? I know that if on the screen i written "USB" the phone and the computer are connected and there is no problem to flash ,but now what ?

well, before you start, put your device into bootloader mode. it will show "serial", then connect it to the pc. test your connection using mtty 1.42 (you'll find several download options here in the forum).
the connection settings for mtty are USB 115200-8-1-No-NONE-None
if it works, connect and press enter, the command shell should show USB> then.
if usb is not present in the connection settings, your connection is not established yet. proceed with the tutorial then. during the entire procedure, the device should remain connected to the pc in bootloader mode, so you install the driver for the right device state.

Hello,
I've problem something like this. Few months ago when i was conecting my phone to computer was everything OK, activesync, disk drive, but now nothing, just charging the phone. I've tryed everything in USB to pc zone, but nothing. When i'm going to bootloader it's writen serial. What can be here?

since you already tried all the different connection methods and even bootloader mode does not connect, there are hardly any options left, where the trouble could be:
- the usb port on the blackstone
- the usb port on the pc
- the cable
you can try another port on the pc (or even better, another pc altogether) and/or another cable, like from a digital camera, an external hdd... (many devices have mini usb cables, you should be able to use either one of those)

[Q] Galaxy S5 CANT FIND USB

Im in England and the phone for S5 for America, how do you find the USB "connection as camera" its not in the notification panel ? im trying to get on Kies, but i cant.

ron101 said:
Im in England and the phone for S5 for America, how do you find the USB "connection as camera" its not in the notification panel ? im trying to get on Kies, but i cant.
Click to expand...
Click to collapse
Do you have the usb drivers installed correctly? Or try another usb port/ cable.

IVE put the USB driver in the c drive along sid the KIES and still it says its (USB) not recognised. Is there something else i could use instead ,i didnt like kies anyway.I tried to get airdroid to work (ive had that for 3 years) but it doesnt handle software (my phone) 4.4.2 it only does 4.3. It says FORBIDEN.FAILED TO SEND MESSAGE on my PC.

Most likely you are using an outdated version of Kies. There are multiple versions of Kies, ensure that you install the latest version of Kies. Then open Kies and have it detect your phone. That is by far the easiest way to install the proper driver for your S5 model. After the driver is in place you can close Kies and never use it again. Or uninstall it if you wish.
Do not use an USB hub, connect directly to your phone. If you have ongoing issues, use a different USB cable and port. Ensure that you are using a data cable, not a charging (only) cable that has the data lines shorted. If your PC has USB driver issues in general, then you'll need to resolve those issues first or use a different PC.
.

fffft said:
Most likely you are using an outdated version of Kies. There are multiple versions of Kies, ensure that you install the latest version of Kies. Then open Kies and have it detect your phone. That is by far the easiest way to install the proper driver for your S5 model. After the driver is in place you can close Kies and never use it again. Or uninstall it if you wish.
Do not use an USB hub, connect directly to your phone. If you have ongoing issues, use a different USB cable and port. Ensure that you are using a data cable, not a charging (only) cable that has the data lines shorted. If your PC has USB driver issues in general, then you'll need to resolve those issues first or use a different PC.
.
Click to expand...
Click to collapse
KIES V3. The trouble is i cant find the USB i now it should be there in the notif panel but it is not, ive got developer options & usb debugging ticked but thats all, have i got to do anything else (hair pulling time) i dont think so?
1) Should i plug it in the mains or usb on the pc
2) Im using the cable that came with the S5 is that good enough.
3) The S5 sits on a cradle shall i take it of.
4) How do i tell data cable, not a charging (only) cable that has the data lines shorted
5) Ive tried 4 different USB software and it gives the message DEVICE DRIVER SOFTWARE WAS NOT SUCCESSFULLY INSTALLED every time
6) Ive done a reboot every time the drivers are put it
ron

ron101 said:
KIES V3. The trouble is i cant find the USB i now it should be there in the notif panel but it is not, ive got developer options & usb debugging ticked but thats all, have i got to do anything else (hair pulling time) i dont think so?
1) Should i plug it in the mains or usb on the pc
2) Im using the cable that came with the S5 is that good enough.
3) The S5 sits on a cradle shall i take it of.
4) How do i tell data cable, not a charging (only) cable that has the data lines shorted
5) Ive tried 4 different USB software and it gives the message DEVICE DRIVER SOFTWARE WAS NOT SUCCESSFULLY INSTALLED every time
6) Ive done a reboot every time the drivers are put it
ron
Click to expand...
Click to collapse
If you use Windows 8(.1) you have to disable driver signature verification to get the usb drivers installed. Here is a tut. https://learn.sparkfun.com/tutorial...abling-signed-driver-enforcement-on-windows-8.

gee2012 said:
If you use Windows 8(.1) you have to disable driver signature verification to get the usb drivers installed. Here is a tut. https://learn.sparkfun.com/tutorial...abling-signed-driver-enforcement-on-windows-8.
Click to expand...
Click to collapse
Noooop its not that i have win 7 pro
ron

You are juggling too many unnecessary variables. Try to simply that and don't skip checking any of the points.
I have no idea what you mean by plug it in the mains? And at least until you solve this you should not be using a cradle, hub or anything else. As I suggested earlier, connect the phone directly to your computer USB hub. And if you have ongoing problems, try a different cable, USB port or even PC.
Making an assumption that the cable that came with the phone is good enough is counter productive. It's not impossible that it may be damaged or have some problem. Borrow or buy another cable, to eliminate one more possible cause of your issue.
Retrace and double check each step. As soon as you make an assumption that it's not worth checking x step because it couldn't possibly be the cause, you are skipping a possible solution. Make sure that you are using the latest Odin, make sure that you installed it from windows administrator mode, connect directly to the PC's USB port, different cable, etc. If you are methodical, you'll resolve the problem.
Good luck
.

Have you activated developer oprions and usb debug?

ron101 said:
IVE put the USB driver in the c drive along sid the KIES and still it says its (USB) not recognised. Is there something else i could use instead ,i didnt like kies anyway.I tried to get airdroid to work (ive had that for 3 years) but it doesnt handle software (my phone) 4.4.2 it only does 4.3. It says FORBIDEN.FAILED TO SEND MESSAGE on my PC.
Click to expand...
Click to collapse
If you haven't given AirDroid permissions to send SMS directly, "FORBIDEN.FAILED TO SEND MESSAGE" might appear. Change the permissions in phone's settings for a try

fffft said:
You are juggling too many unnecessary variables. Try to simply that and don't skip checking any of the points.
I have no idea what you mean by plug it in the mains? And at least until you solve this you should not be using a cradle, hub or anything else. As I suggested earlier, connect the phone directly to your computer USB hub. And if you have ongoing problems, try a different cable, USB port or even PC.
Making an assumption that the cable that came with the phone is good enough is counter productive. It's not impossible that it may be damaged or have some problem. Borrow or buy another cable, to eliminate one more possible cause of your issue.
Retrace and double check each step. As soon as you make an assumption that it's not worth checking x step because it couldn't possibly be the cause, you are skipping a possible solution. Make sure that you are using the latest Odin, make sure that you installed it from windows administrator mode, connect directly to the PC's USB port, different cable, etc. If you are methodical, you'll resolve the problem.
Good luck
.
Click to expand...
Click to collapse
AFTER last nite i started again this morning (im disabled completely down the right side of my body) with a new spirit fffft i got stuck in.So here we go first i put the USB cable in another usb port (one that i havent used) and the phone came alive and that was that it was done.So i tried another usb cable,that also came alive, so that was that it was the usb port that i was using wasnt suitable simple as that. Thank you for all of your help fffft and the rest it was essential for me THANK YOU.