I dropped my phone and the screen now doesnt respond properly: The hardware DID successfully upgrade to the XDA ROM. But touching it causes the backlight to go on, - but most of the keys dont do what one would expect them to do: The phone turns on with a reminder from the calendar on the screen which wont DISMISS or CLOSE. Pressing on the windows logo and then on the phone key causes the calendar to come up and I am not sure which numbers are entered when I do manage to get the phone to come onto the screen (none of the right hand numbers seem to work at all). Does anyone recognise these symptoms and/or could they just show that my SX-56 needs the ROM RE-flashing? I should add that pressing the Master Reset button with this ROM in place seems to make the phone shut off and then when you restart it, all of the data remains in place. I wonder if there is any possibility that the XDA ROM has prevented the reset button from working normally?
A user on another forum said that to him, '"Sounds like the digitiser is up the swanee - have you tried recalibrating it?"
10-12 vertical black lines started appearing to the right hand edge of the screen. Sometimes they are there, sometimes not. THere is usually at last one there somewhere. At about that time the screen stopped responding as I mention. Today the left third started displaying the same veritcal lines, though spaced quite far apart (about a millimetre). Screen doesn't APPEAR cracked: Does this sound like a digitiser and if so, how do you recalibrate it please or is there a link to somewhere on the XDA site which I cant find which might tell me? Or could it be the cable is loose in the circuit board? As you touch the lower right hand corner of the metal casing where the vertical lines are, those lines flash (the right 10 or 12) on and off. And every coloured bar everywhere on the screen or word of text has vertical lines on it (the white parts don't)??
Someone on ebay has said that his phone "fell from my pocket and onto the carpet and the screen cracked, I then used it for about a week" "I sold the screen to someone cause the wanted the touch pad part of the screen for there phone". and wonder what it was he sold or which part can be replaced on it? IS there a touch part and a screen part on this phone?
To be honest, itsounds like you have brocken a connection somewhere between the LCD and the gfx output, probably not possible to repair yourself.
I wonder where the break would be?
I thought that might be the case: I wonder if it would be worthwhile trying to get another screen?
I should probably try to take the unit apart and see if some break somewhere can be identified if it is a break as opposed to some electonic part having failed. It SEEMS to be in the lower right hand corner?
I took apart my tytn, including the screen part.
After reassembling it, I've had random issues related to the keypad and screen.
By keypad, I mean all the keys on the screen part of the phone (D-pad, call/hangup,soft left/right, Internet Explorer & Email).
They will randomly cease working and randomly restart working (usually after turn on/off the screen with the power button)
The screen will also randomly turn white and come back on only if I turn off the screen and then back on.
Im thinking it has to do with a loose connection somewhere in the screen section of the phone, however, Ive taken it apart 2 more times to check everything out and the problem persists.
I wonder if anyone experienced the same thing and found which specific internal is the issue.
i would like to know too cause my buttons just stopped working. so the talk, end, message, Internet explorer, ect. but the left down up right and center button work.
I have the exact same issue.
All the keys (not keybord keys) randomly stops working. I am so used to it now, that I dont even try to answer the phone with the green key button.
The screen fades to white, sometimes (maybe 1-3 times a day).
The screen is white when awakening from "sleep mode", turning on and off the screen fixes that after a while (50% of the time white screen when from sleep mode).
I have found out that putting a finger nail between the keyboard and the screen, on the right hand side, when in closed position, and then putting the screen back on, gives me a 99% chance of funktional display.
The problem also accurs in the "full keyboard position", But putting the finger nail in the same spot helps.
So I think the problem of the connection is in the keyboard part of the phone, since those slide contact always are on the right hand side, and the display contact shift side.
I would lite to know if any body have a permanent solution for this.
(I have now opend my phone yet, and I have tryed the putting thin plastic between the display and the cover, with minimal success)
thanks for your time
alkizmo said:
I took apart my tytn, including the screen part.
After reassembling it, I've had random issues related to the keypad and screen.
By keypad, I mean all the keys on the screen part of the phone (D-pad, call/hangup,soft left/right, Internet Explorer & Email).
They will randomly cease working and randomly restart working (usually after turn on/off the screen with the power button)
The screen will also randomly turn white and come back on only if I turn off the screen and then back on.
Im thinking it has to do with a loose connection somewhere in the screen section of the phone, however, Ive taken it apart 2 more times to check everything out and the problem persists.
I wonder if anyone experienced the same thing and found which specific internal is the issue.
Click to expand...
Click to collapse
These are the exact symptoms of the "SCREEN FADING INTO WHITE" problem. See this thread for more info: http://forum.xda-developers.com/showthread.php?t=303872
The common causes for this are a bad connection to the D-PAD controller PCB (in the technical manual they mention it should be carefully checked and the really small screews with same torque making a 90 degree with the PCB), a bad controller (that was my case, had to order a new one) or not enough pressure on the square black chip on controller (some people seem to have fixed it by putting a plastic sheet in between the chip and the case, to apply constant pressure).
I suggest you try to re-open your phone and reconnect the D-PAD PCB as carefully as you can, double checking the connection and the screws there.
I did fix my problem, by ordering a new PCB and replacing the old (probably bad) one. It started to happen after I dropped my phone and it's the only thing that worked. Now my phone is as good as new.
Hope this helps!
Similar Issues with screen
I have similar issues;
Anything thats on the foreground gets closed by the 'x' button and if I slide it open the start button gets continually pressed!
Seems to be the top right corner of my TS thats at fault
sometimes it's fine....most of the time its not!
Andy.
I have the same! I have a huge dead spot in the middle of my (Tytn) screen, and if you tap there it actually activates the "ok" in the top right corner. The rest of the screen works ok. Whilst drawing in notes any drawing near the center dead spot results in a streak to the top right hand corner...
Bad screen?
Bad rom?
Bad motherboard?
lepic2019 said:
I have the same! I have a huge dead spot in the middle of my (Tytn) screen, and if you tap there it actually activates the "ok" in the top right corner. The rest of the screen works ok. Whilst drawing in notes any drawing near the center dead spot results in a streak to the top right hand corner...
Bad screen?
Bad rom?
Bad motherboard?
Click to expand...
Click to collapse
You can rule out the ROM and M/board in my view for this specific problem. Your issue is very similar (and I think has the same cause) as those who find programs close randomly when in portrait mode and when they open the keyboard the start menu often pops up untapped.
I think this is just a case of a bit of pressure being put on the screen top right corner. Some folks have tried the business card run around under the bezel fix and had some success others have had to return for replacement/repair.
Some have taken the device apart and removed the gasket around the screen under the bezel, but this is not guaranteed to work.
Others have replaced the screen and for this particular problem it is very rarely successful as the screen is not normally damaged.
If you have a warranty use it - all of the above "fixes" are warranty voiding.
Mike
Hi Mike
It's an interesting problem as when performing a click and drag in Notes (drawing mode) the center section of the screen seems to work normally - a square box can select an area right through the middle of the screen - suggesting that the screen (as you say) is OK. So what is causing the a tap in the middle of the screen to register in the top right hand corner, when we now know that the center of the screen can work and respond in the correct manner. The size of the affected area is about the size of a thumb print EXACTLY in the middle. Personally I would like to believe that performing screen alignment 4 - 5 times a day for the past year has worn out the center dot and that is affecting the surrounding area. The trouble is that this fault has been reported on this site a few times now, and everyone says it's caused by something else! What did I do immediately before this happen I hear you ask? I flashed a new radio rom and was fiddling with a piece of card I have wedged down the RHS side of the screen to try and help stabilise the screen alignment. Since this problem arouse, I have removed the gasket - but that hasn't fixed it. I'm going to try and boot up the phone out of the casing to see what "zero" pressure applied to the screen does.
I'll report back...
Lepic.
lepic2019 said:
Hi Mike
It's an interesting problem as when performing a click and drag in Notes (drawing mode) the center section of the screen seems to work normally - a square box can select an area right through the middle of the screen - suggesting that the screen (as you say) is OK. So what is causing the a tap in the middle of the screen to register in the top right hand corner, when we now know that the center of the screen can work and respond in the correct manner. The size of the affected area is about the size of a thumb print EXACTLY in the middle. Personally I would like to believe that performing screen alignment 4 - 5 times a day for the past year has worn out the center dot and that is affecting the surrounding area. The trouble is that this fault has been reported on this site a few times now, and everyone says it's caused by something else! What did I do immediately before this happen I hear you ask? I flashed a new radio rom and was fiddling with a piece of card I have wedged down the RHS side of the screen to try and help stabilise the screen alignment. Since this problem arouse, I have removed the gasket - but that hasn't fixed it. I'm going to try and boot up the phone out of the casing to see what "zero" pressure applied to the screen does.
I'll report back...
Lepic.
Click to expand...
Click to collapse
It will be interesting to see what results you get. You'll need the old rubber band technique to hold the battery in place while you do it!
Mike
Well it's not due to the case squishing the sides of the screen as I just dismantled my hermes, wired it all up in bits on my desk, powered it up and still the screen has a dead spot in the middle and phantom taps in the top right. Temperature is normal room temp, approx 22deg c today.
I'm not sure the exact mechanisms of how these touch screens work out where you are tapping (resistance, voltage), but it looks like there are 3 separate strips running around the screen. 1 goes straight across the bottom, two goes up the LHS and across the top and 3 goes up the RHS. Therefore there is a gap between strips 2 and 3 in the top RH corner. Coincidence? hmmm It seems to me for it to register a tap in the top RH corner, strips 2 and 3 would register low voltages (or high resistance) and bottom wouldn't register at all. Thus suggesting a fault with the PSU that powers the touchscreen. Taps near the edges work because they are near the edges and therefore the resistance is not too great and can be detected, taps in the middle and worse off because they are far from all the detecting edge strips.
Does anyone think that there might a registry tweak for boasting power to the touchscreen?
Hermes Whie Screen Problem
To fix the "white screen" problem, you have to take your unit apart, and reconnect the ribbon cable.
I have a new 8525 and it started happeneing to me, so I took it apart this week, and reseated the ribbon connector.
Fixed the problem.
Has anyone here read and understood all that is said here:
http://msdn2.microsoft.com/en-US/library/aa919680.aspx
Perhaps someone could compare the touch.dll in Black Majik to WM5 - should be the same right?
How come that HKLM/hardware/devicemap/touch doesn't show the touch.dll driver as drivername? Keyboard has it's driver...microsoft says it should say drivername = touch.dll
Do you all have that in your registry?
Every once in a while, the touch screen area at the bottom of the screen by the menu bottom is non reactive. for example when i touch n on the vk, it looks as if im touching h. Is anyone else going through this as well?
just recently my touch screen has problem. when i try to switch screen using touch screen, the screen get stuck half way and shaking. and every time the problem occur, i can't make a selection using touch screen. if i select an icon on the top row, an icon on the bottom row is selected instead.
I've had a few issues lie the two above. I'm not quite sure if it's a hardware of software issue, but resetting the device always seems to work just fine. It's not the best solution, but its better than nothing.
have you tried the VK caliberation tool?
Hi, I was trying to reconfigure my resistive buttons to switch off the screen when driving at night. I managed to reverse the X&Y axis so I have to press in the opposite point in the screen to interface with the OS. Any advice on how to resolve this as I'm just getting more frustrated trying to navigate the menus to make the changes. Would I be better flashing the MCU firmware or the android firmware?
I had this problem before just go to factory settings and change it back
Thanks for the advice but it's difficult to get into factory settings and then what do I do, reset to default I don't see that option?
There's no default option in factory settings
U should go for touch screen settings and change x&y
If you're being difficult getting the factory settings
U can connect keyboard or mouse
That's what I did when I accidentally changed touch screen resolution...
I too am struggling to set it back to normal touch operation i even found one thing where i could see where each finger registered on the other hemisphere of the screen ... Halp me
Try this and say if it works.
In my Head Unit, thats had fixed the problem.
Marcio Abranches-The Bambi reply. I have a Shinzhen Android head stereo C80, 9.1".
I trolled countless pages looking for the solution of 'X' "Y" about face. I dont know what I did to deserve the terrible screw up. But let me say for all those who have also stumbled while stuffing around in this area that this 5 finger technique works on this model as well.
So positive feedback from me. Thanks mate...terrific.
Now the next problem is, how to make active the radio buttons on the left of screen; Home, Return, Vol+, Vol- etc......
In addition to Marcio's instruction, I have this link that takes you to a Youtube description of fixing the same issue and also goes into how to map the side buttons that also drops off.
Hello everybody,
I have a accidentally cracked Pixel 4. The Display cracks after it falls from around one meter height. I decided to fix the screen and buy a new one. It seems to be not an original Bit the board of the new and the old screen seems to be exactly the same. I opened the phone and replace the screen without any damage. After the screen was inserted I test it if it woks. Success! Everything works (I not tested the touch Funktion yet) after I build most of the things together I give it another try and I recognized that the touch Funktion does not work. No matter how hard I press or hold the connector down etc. I tried many things also a Hard Reset. I never seen such problem before. And my question is: is this the screen, the phone or a software problem? And how I can fix this issue? I am completely confused because I fixed many phones but something like this is new. Regularly the complete Amoled does not work.
If I go to the left upper corner, there is some movement in the screen and this also stays if I release my finger (video).
Video 1
Video 2