Hello,
I need some guidance. I flashed the latest version of malaysk ROM. Unfortunately both recovery and the rom give me a blank screen. I know the screen works because I see the malaysk logo when I attempt to go into recovery.
I am presuming I could use a PC and fastboit mode, but how is this fine on an android head unit.
I have a 1 din, flip screen type, KLD5, RK3188 model.
Please help me.
There seem to be a lot of units flashed with the latest rom that have lost the bootloader and recovery.. I'm not seeing any fixes for this. Has anyone fixed a unit that is now stuck at the bootloader with no recovery possible?
Sent from my SM-G928F using Tapatalk
I did not try it, but this might work:
Holding the power button while turning on the unit will get you into bootloader mode. **This is battery power not acc power** The screen will be black but plugging in a usb to the front usb will prompt the PC to install the RockChip bootloader drivers - this might help http://www.cnx-software.com/2013/11...install-rockchip-usb-drivers-in-windows-xp78/
(From http://forum.xda-developers.com/wiki/Hui_Fei_Type#Bootloader_mode)
I don’t have a power button on my HU, I wonder if the RST button or the smaller reset button above would work?
Sent from my SM-G928F using Tapatalk
Hello there,
I have been a reader of XDA for many years but this is the first time I'm at a loss...
I have this radio: Seicane S088713 but with the T3 processor. Sorry I cannot post links (I'm a newbie!) but you can see it if you search for "9 inch 2004-2008 Chrysler Aspen 300C Android 6.0"
I managed to root it with Kingroot and all seemed fine for a while but I must have deleted something by mistake and now the unit is stack on the android screen.
Any idea how to enter recovery mode? The radio does not have any buttons or reset pin.
Also tried the Alt+PrtSCr+i but all I manage to get is the unit to reboot.
Any ideas? I have looked a fair bit of info on this particular radio but there's no much on it.
Have you find the way to get into recovery mode in the meanwhile?
I have a seicane with allwin T8, would also love to know how to enter recovery mode, if there even is one lol.
Recovery - worked for me
Did you repeatedly hit the "i" while holding the "alt + prnt scrn" buttons?
Even after the first boot screen starts?
It takes a little patience and practice if it will work at all.
If you have a poweroff button, just push it for quite some time and then push again and wait for the head unit to start, it should start right on the recovery menu after that.
I've only tried it once, and it did.
Hope you'll get there too.
Hello,
I upgrade my T3 P3 Quad Core Headunit to Android 7.1.1 using the rom given at:
4pda.ru
/forum/index.php?showtopic=837879
(With the help of Google translate)
I missed upgrading the recovery in the process because of which I cannot run the system upgrade now.
I would be grateful if someone who has upgraded their T3 P3 Quad Core headunit to Android 7.1.1 could post a copy of their Recovery.img file (can be obtained using the terminal of and application such as Rashr).
Thanks.
Shahzad76 said:
Hello,
I missed upgrading the recovery in the process because of which I cannot run the system upgrade now.
Thanks.
Click to expand...
Click to collapse
1. You are mistaken. Recovery does not perform the update function.
2. If you had Android 6 and you upgraded to Android 7, then now you need to use the method of emergency firmware update.
3. What firmware do you want to install?
****-jones said:
1. You are mistaken. Recovery does not perform the update function.
2. If you had Android 6 and you upgraded to Android 7, then now you need to use the method of emergency firmware update.
3. What firmware do you want to install?
Click to expand...
Click to collapse
Thank you for the response.
I installed version V8.3.2_20180105.162617_AKW1-mod and would now like to upgrade to V8.3.2_20180119.100305_TW2-ZHC-mod.
Both of these are Android 7.1.x. When I run "system update" the processing icon shows for 1-2 minutes and then android reboots. However, after boot up the rom version still shows the same 20180105.
If I boot into recovery the version shown is android 6.0.1. Was assuming that the system update isn't working because the recovery was not updated.
Would appreciate your guidance on how to upgrade the Android 7 version & if the recovery update will help or not.
Thanks.
Shahzad76 said:
Thank you for the response.
I installed version V8.3.2_20180105.162617_AKW1-mod and would now like to upgrade to V8.3.2_20180119.100305_TW2-ZHC-mod.
Both of these are Android 7.1.x. When I run "system update" the processing icon shows for 1-2 minutes and then android reboots. However, after boot up the rom version still shows the same 20180105.
If I boot into recovery the version shown is android 6.0.1. Was assuming that the system update isn't working because the recovery was not updated.
Would appreciate your guidance on how to upgrade the Android 7 version & if the recovery update will help or not.
Thanks.
Click to expand...
Click to collapse
You need to rename the firmware files, as you did the first time.
Use these methods of emergency firmware update.
1. Hold Home (mechanical button), press Reset, and keep holding Home until the update starts.
Instead of the Home button, you can connect the KEY1 (Steering wheel controls) wire to the ground. Or press the button on the steering wheel connected to KEY1.
2. Yet another procedure might be needed for some units: Using a USB stick prepared as above and inserted in the unit, turn ignition to ACC, press Reset, turn ignition off, then after 5 seconds turn it again to ACC.
Read item 2 (Flashing firmware) of this post https://forum.xda-developers.com/an...6-astard7-android-6-0-1-t3523906/post70207172
Good luck.
****-jones said:
You need to rename the firmware files, as you did the first time.
Use these methods of emergency firmware update.
1. Hold Home (mechanical button), press Reset, and keep holding Home until the update starts.
Instead of the Home button, you can connect the KEY1 (Steering wheel controls) wire to the ground. Or press the button on the steering wheel connected to KEY1.
2. Yet another procedure might be needed for some units: Using a USB stick prepared as above and inserted in the unit, turn ignition to ACC, press Reset, turn ignition off, then after 5 seconds turn it again to ACC.
Read item 2 (Flashing firmware) of this post https://forum.xda-developers.com/an...6-astard7-android-6-0-1-t3523906/post70207172
Good luck.
Click to expand...
Click to collapse
Thank you for the help. The ACC procedure worked like a gem. :good: :good: :good:
Salve a tutti vorrei un aiuto da voi ho un autoradio cinese allwinner t3 p3 2gb ram vorrei aggiornare 7.1.1 mi potete dare il link del firmaware grazie
****-jones said:
You need to rename the firmware files, as you did the first time.
Use these methods of emergency firmware update.
1. Hold Home (mechanical button), press Reset, and keep holding Home until the update starts.
Instead of the Home button, you can connect the KEY1 (Steering wheel controls) wire to the ground. Or press the button on the steering wheel connected to KEY1.
2. Yet another procedure might be needed for some units: Using a USB stick prepared as above and inserted in the unit, turn ignition to ACC, press Reset, turn ignition off, then after 5 seconds turn it again to ACC.
Read item 2 (Flashing firmware) of this post https://forum.xda-developers.com/an...6-astard7-android-6-0-1-t3523906/post70207172
Good luck.
Click to expand...
Click to collapse
Hello,
Sorry for using this topic but I'm a new user...
I have an Android 7.1 radio that doesn't work correctly after disconnecting the canbus box from it.
I did a video https://youtu.be/PcQrKQD8FKs
Can you help with is?
Hi Intrusion4,
I know it's an old post but I'm having the same problem on a Allwinner T3 P3.
At first the Bluetooth stopped working 6 months ago but that didn't bothered me too much, instead this morning i found the GPS icon blinking and everything not related to the Android OS stopped working (Radio, Music Player, Navigation, Car Info, etc). I can't raise the volume and brightness either just like you in your video.
Do you still remember if you solved it and how did you do it?
Thank you
Hi!
I'm looking for instructions how to enter the recovery mode in this head unit (it's Ford Mondeo MK4). I was trying different combinations, such as holding RST button for 30+seconds, holding power button, touching screen etc... Maybe someone went through the same problem and has a solution.
Thanks in advance!
Helllo, you found samething? I look for a firmware update about this radio.
Hello Team ,
Just bought a new head unit '' Sadocom PX6 android 10 but when mounted I got a problem with a panel buttons so I reset the unit from the rest button then it entered to the recovery mode but I can't exit it after I finished the reset , I downloaded deferent firmware and MCU but without success, its stuck in recovery mode with all buttons leds blinking, and all physical buttons not dowing anything.
Any solution please.
Thanks in advance .
Try to see if the strip connecting the main board and physical key board is perfectly attached.
It might have been displaced.
Atleast touch or any physical button must work.
Or the physical button you are mentioning might have stuck or shorted, try to remove and replace it or- just try to detach the strip containing the physical key board( only the strip is for physical keys only).