[NST] Button broke :( - Nook Touch General

Just found out that the upper left button on my NST (1st gen) doesn't work anymore. Isn't a major issue for anything except for navigating the menus NookManager so far. Anyone else run into dead buttons on old NSTs? And I know this is a super-long shot but anyone have luck fixing one?

You can try. The NST is easy to take apart. It's just the screw under the power button then slide.
The PCB comes out with a T-6 driver (opinions vary, my T-5 is a bit loose).
After the PCB is removed see if the switch still clicks or if there is some problem with the front plate of the NST
Unfortunately the button is just a collapsible dome switch under a patch of rubber.
You could try removing it on one side, cleaning under it with a swab of isopropyl then gluing down the edge.
Good luck!

Related

Hardware buttons doesn't work anymore on my Trinity.

Hi all, my Trinity's hardware buttons doesn't work.
The 2 softkey hardware buttons, the red and the green button, the ok button and the Start button seems to be broken also if they have backlight. All the others buttons are ok.
I've tried to softreset, hardreset and flash the ROM (I'm using last Ervius ROM). After flashing for the first time the buttons were ok for a littewhile but now they seems to be broken again even after several flash. I've also tried to downgrade to wm5 but nothing change. I think that is an hardware issue and I'm going to try to fix it by opening my Trinity hoping that is just a flat connector pluged out but if someone else has experienced the same problem and has to suggest me something is really welcome.
Campo said:
Hi all, my Trinity's hardware buttons doesn't work.
The 2 softkey hardware buttons, the red and the green button, the ok button and the Start button seems to be broken also if they have backlight. All the others buttons are ok.
I've tried to softreset, hardreset and flash the ROM (I'm using last Ervius ROM). After flashing for the first time the buttons were ok for a littewhile but now they seems to be broken again even after several flash. I've also tried to downgrade to wm5 but nothing change. I think that is an hardware issue and I'm going to try to fix it by opening my Trinity hoping that is just a flat connector pluged out but if someone else has experienced the same problem and has to suggest me something is really welcome.
Click to expand...
Click to collapse
I experienced this myself, and replaced this item:
http://cnn.cn/shop/p3600dopod-d810-keypad-p-1825.html
HPN
keys are stuck
Mine also, but solved it after a couple of days (temporarily). The hardware buttons problem seems to be related with one of the keys stuck. If one of those keys is stuck none of the others work. I tried "fast" double clicking on one key at a time to unstuck and it worked for me. Mine has been working for two weeks with no problem. Anyway I ordered that part "just in case".
So before opening your trinity try to unstuck the keys. It seems to be related with humidity conditions and carrying the phone in the pocket (just a guess).
hpn said:
I experienced this myself, and replaced this item:
http://cnn.cn/shop/p3600dopod-d810-keypad-p-1825.html
HPN
Click to expand...
Click to collapse
Thanks !
n0t said:
Mine also, but solved it after a couple of days (temporarily). The hardware buttons problem seems to be related with one of the keys stuck. If one of those keys is stuck none of the others work. I tried "fast" double clicking on one key at a time to unstuck and it worked for me. Mine has been working for two weeks with no problem. Anyway I ordered that part "just in case".
So before opening your trinity try to unstuck the keys. It seems to be related with humidity conditions and carrying the phone in the pocket (just a guess).
Click to expand...
Click to collapse
I'm going to try this becouse during the last 4 days sometimes the buttons work so.... thanks!
Ok, nothing work.
I've also tried to open the device but looking behind the buttons pad fortunally/unfortunally there isn't an evident hardware problem.
The only solution is to replace the pad.
Hi to all.
I have had buttons not working on my trinity for some time. was tempted to send it back for repair but i did not want to be without my phone and did not want to have to stick the old wm5 rom back on!!
I took my trinity apart too see if i could see anything wrong. and got it down to the keypad. one thing i did notice is that there was a lot of dust. also around the small disks that provide the buttons, there are 3 small holes in the sealing sheet. seems that the construction of the switch array is circuit board at the bottom, with small tin disks on top, all held in place with a thin plastic sheet.
The tin disks 'pop' inside out when you press the buttons, making the contact for the switch. On the old nokia phones, these disks got deformed and this would make the button work but with no click. I had a click but no button operation, and with the holes, and all the dust i found, i figured that it must be dusty contacts.
so here is how i managed to fix my buttons for free:
1, strip the phone to get to the keyboard circuit (i used this link clicky)
2, clean all the dust from the buttons
3, start to tease the plastic film from the front of the board (i used a sharp knife but mind your fingers and take care not to damage the board)
4, once one corner is up you should be able to slowly pull the film up (take care not to damage the disks as the plastic comes up but make sure the disks stay on the plastic sheet)
5, dont pull the sheet totally off otherwise you will have a job getting it all to line up after.
6, get some alcohol or head cleaning fluid on a cotton bud and clean all the gold contacts, as well as the insides of the discs.
7, slowly rub the plastic film to put it back where it came from, taking care to get the disks in the center of the gold contacts.
8, rebuild and test
All being well you should have working buttons again!!! It seems the design of the buttons lets dust inside the workings.
Hope this helps someone with clicking buttons but no action!!!

Has anyone opened up their HD2??

Hey anyone already opened up their HD2? I need to open mine since my back button got stuck while my baby girl tried to press too hard on it. Now the back button feels like it's not presing at all compared to the other buttons.
i also have a spare housing that I am thinking of putting in.
Anyone can point me to the right direction?
Thanks
i've had the back off mine.
first search youtube for leo disassembly and you'll find an htc disassembly video: "leo Ds" (and another "leo As" for reassembly). they are somewhat daunting, but do not despair!
mine came back from a htc warranty service with a fingerprint on the inside of the lens glass and i couldn't be bothered sending it back again for cleaning so i did it myself. cracking the case isn't all that easy, or wasn't for me.
after you remove the 4 screws (get the void sticker and moisture indicator out with a pin), you still have to unclip the back from the chassis. WHY do electronics manufacturers design them like that??! in the video the tech uses a plastic hooked tool which i do not possess so i had to rely on my fingernails -- which i nearly pulled out! i tried for a good 15 minutes before it finally separated (with me sweating all the way that i was going to damage the LCD with the force i was having to apply). but it all finished happily in the end.
good luck with yours!
Not sure if it's worth it.
1st things 1st, watch the video on youtube..
.
Assuming u broke the keypad (just like me, but mine is right in the middle) at about the 6th minute of the disassembly video, they'll show u where u'd be replacing the keypad.
Removing the 'lcm and follow the indicator' isnt as simple as it look. you'd find the glue to be really tough. Putting it in an oven, sure, it'd be hot to the touch, and let it cool down a bit it'd be hard again. Hairdryer? Still too hot. Gloves?u'll lose touch sesitivity. So what i did was use a small blade/box cutter and cut which ever visible glue... and assembling, i had to replace all the double sided tape with some cheap ones...weak ones. Could be a good thing.. or a bad thing. Good, cos i know i dont have to wrestle with some really tough glue..in case i ruined my lcd again.... bad.. cos its..not that secure, i rmember that i nearly ripped it open unintentionally!
Neway replacing my digitizer+lcd took about 3 hours...had a couple of breaks, and spent 15 mins looking for the proximity sensor or was it the ambient light sense 'lense'..very tiny things those things are. So be careful...cos i eventually lost it..grrr
Anyway, Best of luck.. .now to find a replacement keypad that cost less than 5usd..hehe
dsx2b said:
1st things 1st, watch the video on youtube..
spent 15 mins looking for the proximity sensor or was it the ambient light sense 'lense'..very tiny things those things are. So be careful...cos i eventually lost it..grrr5usd..hehe
Click to expand...
Click to collapse
a good tip here is to work with the phone in a large tupperware box so that if something drops out it can't go anywhere.
note to the OP: i've read several posts where people damaged the ribbon cable connecting the bottom buttons to the mainboard so be careful. it looks very delicate.
Having just opened mine up several times recently I can offer a couple of tips.
1. Unscrew the four screws - they are T5 torx size.
2. Use thin stiff plastic pieces (I found the plastic case that nails are sold in to be the right stiffness and thickness). Cut some up and push them between the case and the phone works so that they hold each of the locking tabs out in turn. I used five or six bits to do this. Three on the vol control side, two at the top and one on the top area of the other side.
3. Then pushing out at the top where the battery would sit while prying with finger nails outward on the long vol control side you can work each of the locking tabs out so the plastic bits hold them unlocked. Do this along that side, across the top and down the other side working each one a little bit as you go and repeat.
4. This should allow the top edge to come out allowing you to lift is out and "up" so that the button end slides out.
This worked very well for me..several times.
The display is held to the electronics portion by double sided tape and yes it is very strong. But you can soften the adhesion significantly using a heat gun. But you must be careful to heat the whole area to avoid thermal differences cracking the screen. The heat will loosen the tapes grip allowing you to pry the screen away from the electronics side.
Note that the screen is made up of the LCD covered by the glued on digitizer and they are connected with a single ribbon cable on the lower right hand side (I think from memory). This means the screen has to lift off with a hinge action. Lifting along the opposite long edge to the ribbon cable, rather than lift from the top or bottom.
Hope this helps.
Hi, I tried to open mine and followeed the video, be careful as the video makes it look much easier than what it really is, I ended up ruining my device, just take your time and do it slowly.
Thanks guys! Gonna try it over the weekend. Worst case is that I break my case or put some cosmetic damage. I have a spare case though hehe.
The problem about the key is the back button feels stuck.... the other buttons are snappy and have a tactile sort of feel, where as the back button doesn't have the same feel. looks like it was pressed to hard and never popped back up...
just annoying when i've been very careful with the phone.
ok looks like i wouldn't have to open my phone.... i tried to but then there's a warranty void sticker, so I just called tmobile and explained about the back key being stuck.... and they're sending me a replacement.
i'm gonna lose my invisible shield full body though... but better than risking breaking my phone....

[Q] Broken LCD screen :(

Hey im panicing so bad rite now. I just broke my htc's LCD screen ! Mad sad from this disaster . Dont got much money so can someone please tell me whats the cheapest or best way to replace or fix it ? I really need help because im freaking out!
The repair choices
There are basically two choices. Doing it yourself or having it repaired.
In either case the most straight forward is to replace the screen and digitizer as one unit. I expect you can still see things on the screen yet its cracked from one corner. Its the digitizer on the top that usually suffers but its hard to replace by itself. There is a YouTube video showing how to do this (search on Replace Touch Screen on HTC HD2 on YouTube).
If you are game to do it yourself (an electronics tech would be able to do it fairly well, though it is still fairly difficult) then you can buy a complete screen and digitizer off ebay (around $100). Getting the unit out of the case is tricky as its held in with 4xT5 Torx screws (easy bit) and lock notches around the case (tricky part). I found thin stiff plastic bits slotted in between the module and the case works well at releasing the locking notches. Then press out at the top of the battery area, while pulling the top edge of the plastic case out and down with your finger nails. One side at a time. Don't forget to remove the SIM card and SD card as these will hold the module in place if not removed.
The double sided tapes used to hold the screen in place are a problem, but warming them up with a carefully applied heat gun does release them. I would add that there is no need to unscrew any of the electronics boards as the screen can be replaced without doing this. Releasing the screen ribbon cable connector is done by flipping up the black locking section on the ribbon socket. Slide in the new cable, lock it down, then curl it around as you slide it backward under the metal case so that the curl in the cable occurs in that small space under the metal rather than being folded over sharply, which can fracture the ribbon cable "wires" rendering the screen dead.
Press the screen back down onto the tape (hopefully the tape has remained slick enough as its all that holds the screen in place). Be careful to align the edges and top and bottom correctly, otherwise your buttons won't work and the screen will not sit in the case properly. You can test the buttons as you align to feel for the slight click. Be sure to test all four as alignment left to right is just as critical for full function as up and down. You should also watch to be sure the light sensor little plastic bit (its a small clear cube of plastic) doesn't fall out and disappear while you are doing the screen swap and it stays in place during reassembly.
Then press it home into the plastic case. I remove the volume button (if it hasn't fallen out already) as it tends to push the volume button pads out of alignment (they are only held in with yellow tape (be careful not to loose them). Then with it all snapped in place pull out at the volume button section and slot the button back in place. Orientation is fairly obvious with the button points lower down and the joining bar going behind the case plastic to lock it in place (all with the screen facing upward). You may find the volume button only works if you press down on the screen slightly. This movement will be taken up when you screw the 4 torx screws back in.
Finish by powering up (with fingers crossed) and test. Hopefully all working.
Alternatively, if thats put you off doing it yourself, get it repaired by a service agent (around $300). Then it comes back all done with a small warranty. Most of the phone providers will be able to direct you to a good independent service agent.

[Q] Keyboard Malfunction...

Hi Guys,
so I noticed over time that a couple keys weren't working on my dream's keyboard sometimes, and it became progressively worse up to the point where said keys stopped working altogether. The Affected keys are: 1, 2, W, S, Z, Left ALT, Volume Up. If you have a look at your keyboard, you will notice they are in a line almost, which led me to think there was a problem on the Keyboard PCB, or it's ribbon connector to the Motherboard.
SO...I bought one of these Ebay PCB replacements: http://cgi.ebay.com/T-MOBILE-G1-HTC-DREAM-KEYBOARD-MEMBRANE-KEYPAD-PCB-FIX-/120690721519?pt=PDA_Accessories&hash=item1c19ba42ef and just fitted today but, and to my disappointment and dismay, the exact same keys still do not work
I have cleaned the internals using compressed air quite thoroughly and still not winning.
Any ideas as to what the real problem is here? Maybe its the motherboard itself?
THANKS!
I have a problem with my right alt and . Key as well, hope we can solve this
Sent from my Plain Biff Dream using XDA App
It is not particularly clear what that item is. Is it a complete keyboard? PCB? Just the rubber membrane?
The key is to CLEAN the thing. 99.9% of keyboard problems are because there is dirt somewhere. Rubbing alcohol and a mild abrasive (like a pink rubber pencil eraser) are very useful for cleaning.
Its everything you see in the picture, keyboard pcb (which has the actual buttons which are pressed when you press the plastic button above, and the volume buttons), with ribbon cables, metal part that sits behind the keyboard - (it is not a replacement for the buttons on the rubber strip which overlays the keyboards hardware)
I stripped the phone completely and replaced the entire keyboard pcb, and still the same issue... i don't understand how cleaning would have made a difference on a brand new item... where else do you recommend i clean?

HD2's innards: Attempted vibration motor fix gone horribly wrong.. HELP!

I'm hoping somebody with some knowledge of the HD2's innards can help me...
My vibration stopped working on my HD2. I found the plastic LED flash cover to be 'pushed in' (with the help of a couple xda threads I dug up). Others said it was an easy fix: Open the case and push that piece of plastic back into place.
I opened up the case to correct it. But after putting it back together not only does vibrate not work, but the volume keys, speakers (both earpiece and speakerphone), flash, notification led, and camera all don't work.
I obviously screwed something up, but I have no clue what it could have been. I was very careful. One thing I'll note is that when I pulled the case apart, the plastic volume rocker went flying. When putting the phone back together I got it back into place so that I THOUGHT it should work (it was seated properly and felt "clicky" for up/down movements.
But clearly wasn't just the volume rocker that was affected. It doesn't seem that I pulled anything else loose or anything like that...
But no luck, all that I listed above is non functional, and what I'm left with is a glorified 3.5 in tablet
Any ideas?? Thanks in advance!!!
Snapped a couple quick pics which may help:
http://i50.tinypic.com/mmsa36.jpg
http://i47.tinypic.com/sl1kdx.jpg
Unfortunately when comparing these to other pictures of the inside of the HD2 that I found online, I fail to see any differences, or anything I could have inadvertently screwed up.
Most likely you screwed up(or disconnected from motherboard) somehow your main flexboard, but your picture are not usable for this, you should take off your motherboard+main flexboard from chassis to have a full view!
You probobly just disconnected a small cable. I have no idea of the HD2 innards but did multiple repairs of small stuffs and the flat cables hold in place by a plastic clicker pull out easily - just reopen and check them all, you should be fine.
Thanks for the input! I figured it's something like that, just one small cable. But I didn't even take off the board at all... The pictures show the full extent of the disassembly... Do we still think it's necessary to disassemble it further?
I checked all visible connections, but yeah, maybe I somehow yanked out something that is NOT visible. I'll try to check again today... In the meantime, any more ideas from anyone else? Thanks!
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Have u tried starting up the phone without the backing? I had this issue when I painted my housing the led cover was stopping the motor from spinning but if i took out the backing it works. So I just trimmed the led cover and now it works.
Mister B said:
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Click to expand...
Click to collapse
I'm nooby with regard to this stuff; I only attempted the repair since I read in a couple other threads about multiple self-proclaimed non-super-tech savvy people were able to open it up and move the plastic LED cover for an easy fix.
So what exactly am I looking for with regard to the main-flex? Where is it? I thought I wouldn't really see that unless I removed the board which I haven't done... is it still possible I knocked it loose or damaged it? I didn't think that would be possible since I ONLY removed the back cover (though it does take a slightly uncomfortable amount of force to do so, so I guess anything can happen...).
If not the main flex cable, is there anything else specific to look at which may be disconnected? It seems to be all the stuff at the top of the phone that fails to work (camera, speakers, vibration, flash, volume keys). While the stuff on the bottom (other hardware buttons, charging jack, headphone jack, etc).
THanks!
I have given up. After being stumped briefly how to hard reset the device without the volume keys working (I have Android installed), I was able to do it via ADB from the Android dev kit.
To ebay I go...

Categories

Resources