Hello guys. I picked up an A-Sure 9" touch screen head unit to put into my MK5 GTi. I got it as it was local and only 50 euro. Tested it at home, workes perfect, couldn't reset the system due to a password but little bit of googling got me 3368 code which worked!
Today I spent a good while downloading Spotify, Google Maps etc. To the unit. Set it up in the car, all going well. I had to turn the car key on/off a couple of times and the unit booted with the usual VW logo however a message underneath that said something like "system not started 3 times fully, will self-test and restar automaticallt". Aaaaand that's where I am now, can't get anything else out of it ?? Any help is apprreciated. Managed to get some screen when I held the vol up+down buttons, said API Active:3 and Intel Sofia 6 I believe? The wait here and nothing again.
What did reseller suggest to try and resolve?
Related
Good morning, I have got an Avin unit Avant 2 for BMW E46 purchased on january 2015 with Android 4.4.1 and last firmware release
After two years of perfect run now I have a big problem. I want to make a short summary of avin e46 isuues. (sorry for my bad english)
On the 2th January 2017 in the afternoon I start my car from a park and avin unit run without problem;
After 10 min of travel with navi on, unit stop to run screen become black and when I restart the car or the unit avin logo was showed for a few second and after disappear:
On the 3th January 2017 when I start my car in the mornng unit was run regular but during the day i park my car and when i restart I've got the same issue of day before. So I try to make a soft reset but nothing run (
On the 4th january 2017 I hope then unit start after the night but when I start my car in the morning nothing run. Avin logo appears NOW for less than a second and anything run.
So I wrote an email to Avin support and after I try to:
- check wires and check battery (wires ok battery is a brand new exide plus)
- made reset factory whit power button (8 shot + 1 15 sec as you suggest) result RESET FACTORY DON'T START
- update with sd card in navi slot and reset hole with your software update result UPDATE DON'T START
- remove unit from the car and power in with a 12v dc external power source result SAME ISSUE THAN MOUNTED IN CAR
All thing that I do give me the same response: nothing.... run and avin logo for less then a second (power is ok because red light is on, cd run ecc ecc)
Please someone can help me because buying this quality unit was very expensive I have preferred it for a cinese unit but I need that it works fine. Thank you Marco
Avon avant 2 stuck on logo
My unit powers up, shows the BMW logo and then stays on Android logo and won't move on from that. I have tried the 8x power button rest but can't reset. Could this be a power issue.
Marco did you find a solution for yours?
Hi there,
After doing an upgrade my unit it stuck with a black screen and need to get into recovery mode in order to reload a working firmware.
Anyone any idea how to get there?
Tried the reset button for some time with and without home or on/off button and also removed the power source and pressed reset while putting power back but nothing seems to work
So i'm stuck for now :crying:
Any help?
Did you ever get your unit fixed? Did you try restarting with a USB plugged in with the firmware file on it?
No sorry... never got it working again. Had to send it back for a replacement unit.
I've been doing a lot of back and forth with their support on another issue and I've updated my MCU and software so many times now I thought maybe I'd be able to give you a hand.
Do you use any navigation apps on your Avant4? When I use ones that have voice navigation, the voice is getting truncated at the start and end of the directions. Some apps more than others and it seems to be related to those apps that use TTS (Text to Speech).
I'm using Waze via Android Auto. So i'm not having this problem.
So it runs from your phone and just displays on the Avant4? I have Waze running on the unit directly and it gets truncated.
I have al running on my phone and use a Android Auto box.
U can buy it from Avin USA. See website for all options on your Avant4.
wouterverboom said:
No sorry... never got it working again. Had to send it back for a replacement unit.
Click to expand...
Click to collapse
If you hold the volume knob until it starts blinking then let go and hold it down again it will boot the unit into recovery mode.
Hello,
I have 2 head Units - both have the same issue of not rebooting when powered up. EACH UNIT freezes on the initial power up - none of the buttons work and the screen displays "Android". I have tried disconnecting power - left it on over night but nothing seems to allow it to engage past the initial power up.
Kianda Mfg. has been no help; their customer service is non-existent. I even tried to mail one of the units back to China and it got returned costing me an extra $140.
Looking to see if there is a firmware i can use to reset/ reboot the units. It is a rockchip rk3368:10/ QP1A. 190711.019/df11221744.
Thanks, Bill
I just purchased a px30 head unit advw9010.
It ran good for about 30 minutes and then the entire row of keys stopped working, i think the reset button is dead too.
When i went into factory setting the keymap does not recognize the key presses, when i went to exit it said it needed to reboot, during reboot my delay power may have turned off but not sure.
Now the system is stuck in boot loop
It displays the main start screen briefly, blinks the button lights 3 times and reboots after a few seconds.
Key combos and rst button does not seem to do anything as i expected.
Is there anyway to get this out of a bootloop? Or am i stuck with a $200 brand new paperweight. The seller is not being helpfull at all
post system info, MCU version and read through forums
The only info i can get is through the sale listing. The unit does not boot so i cant see the mcu info unless there is another way? Its a px30 quad core 2 gb ram 9" screen with android 10
I have been looking on forums the last few days but cant find any relevant info on my unit, and since the button row and reset doesnt work im stuck
Update:
The seller is finally helping out, i will get the firmware sometime overnight.
I dont think it will help with the row of buttons not working but i will update this accordingly and post the mcu and more details as soon as the systems back up and running
Hello everyone,
I have a problem:
Out of nowhere, my Head Unit turn the music to the max volume, the button response after a maximum of 10 seconds, then I can turn down the volume. Also sometime, if I press anywhere on the screen, the radio turns off or restarts.
think is something related to the software.
Is there any update for this headunit? i attach some photos of the MCU and system version.
I tried to find the device's name/model and updates, but without success. (I've tried already factory reset).
thanks in advance for thinking along.
Greetz from Amsterdam
Hi, try first disconnecting canbus box if you have it at all on this device. Then start up head unit without canbus and wait for 30 sec then shut down headunit and car engine.
Connect canbus again on the back.
Start in contact mode of car, and as soon as unit starts start tapping on center of screen with all five fingers. When reovery mode activated it will proceed automatically and finish. (procedure will erase data and install again!)
Then try if errors and bugs are fixed.
Hello, just an update. Unfortunately this trick doesn't work. Is there a software update for it?
Ask your seller for solution, probably will be or you must do complete install / flash of ROM memory and install again everything.