Good morning, I have got an Avin unit Avant 2 for BMW E46 purchased on january 2015 with Android 4.4.1 and last firmware release
After two years of perfect run now I have a big problem. I want to make a short summary of avin e46 isuues. (sorry for my bad english)
On the 2th January 2017 in the afternoon I start my car from a park and avin unit run without problem;
After 10 min of travel with navi on, unit stop to run screen become black and when I restart the car or the unit avin logo was showed for a few second and after disappear:
On the 3th January 2017 when I start my car in the mornng unit was run regular but during the day i park my car and when i restart I've got the same issue of day before. So I try to make a soft reset but nothing run (
On the 4th january 2017 I hope then unit start after the night but when I start my car in the morning nothing run. Avin logo appears NOW for less than a second and anything run.
So I wrote an email to Avin support and after I try to:
- check wires and check battery (wires ok battery is a brand new exide plus)
- made reset factory whit power button (8 shot + 1 15 sec as you suggest) result RESET FACTORY DON'T START
- update with sd card in navi slot and reset hole with your software update result UPDATE DON'T START
- remove unit from the car and power in with a 12v dc external power source result SAME ISSUE THAN MOUNTED IN CAR
All thing that I do give me the same response: nothing.... run and avin logo for less then a second (power is ok because red light is on, cd run ecc ecc)
Please someone can help me because buying this quality unit was very expensive I have preferred it for a cinese unit but I need that it works fine. Thank you Marco
Avon avant 2 stuck on logo
My unit powers up, shows the BMW logo and then stays on Android logo and won't move on from that. I have tried the 8x power button rest but can't reset. Could this be a power issue.
Marco did you find a solution for yours?
Related
Hello guys. I picked up an A-Sure 9" touch screen head unit to put into my MK5 GTi. I got it as it was local and only 50 euro. Tested it at home, workes perfect, couldn't reset the system due to a password but little bit of googling got me 3368 code which worked!
Today I spent a good while downloading Spotify, Google Maps etc. To the unit. Set it up in the car, all going well. I had to turn the car key on/off a couple of times and the unit booted with the usual VW logo however a message underneath that said something like "system not started 3 times fully, will self-test and restar automaticallt". Aaaaand that's where I am now, can't get anything else out of it ?? Any help is apprreciated. Managed to get some screen when I held the vol up+down buttons, said API Active:3 and Intel Sofia 6 I believe? The wait here and nothing again.
What did reseller suggest to try and resolve?
I have an Allwinner T8 which had been working fine until yesterday. It's running stock firmware and unrooted. Yesterday coming home from work it started to boot loop. The radio would come on for a few seconds, then go off, the display constantly shoing the turning android.
I had hoped it was just hot as it was a very hot day, but was the same this morning. I've tried pressing the reset button to no avail, it just no longer plays a radio station as it's lost the stored stations.
I cannot seem to find a way to get into recovery mode, tried plugging in a USB keyboard and pressing "i" and CTRL-PrintScrn but nothing.
Can anyone offer any advice before it ends up as landfill?
I have the same problem with an Allwinner T8 team.
I have a 2016 jeep renegade sport plus. Supposedly the android team is a winca S300.
And it was in a loop, it does not start the system and it stays in the android logo.
I saw a way for the system to update itself.
1) the key must be connected - without starting - just making contact - power -
2) when the device reaches the android logo, it must be reset.
3) When the equipment is restarted, before the logo appears, the ignition key must be turned and removed.
4) After that, the start key must be reconnected. This should bring up an update banner.
The problem is finding that software, which should be previously installed on a flash drive.
Does anyone know how to get it?
Hello,
I have 2 head Units - both have the same issue of not rebooting when powered up. EACH UNIT freezes on the initial power up - none of the buttons work and the screen displays "Android". I have tried disconnecting power - left it on over night but nothing seems to allow it to engage past the initial power up.
Kianda Mfg. has been no help; their customer service is non-existent. I even tried to mail one of the units back to China and it got returned costing me an extra $140.
Looking to see if there is a firmware i can use to reset/ reboot the units. It is a rockchip rk3368:10/ QP1A. 190711.019/df11221744.
Thanks, Bill
Sorry for the newbie post, I am a computer guy but haven't messed with these android head units. Looks like there isn't much out there for this problem/unit or unit problem lol.
US $79.93 32%OFF | 10.1 Inch Android10.0 1Din Car 4Core Stereo Radio GPS Navigation WIFI Bluetooth Audio Universal Multimedia Radio Player
https://a.aliexpress.com/_mspYyDs
Model: 10.1 Inch Universal
ROM: WIFI 2-16GB 2.5D
I bought this off an eBay seller ( https://www.ebay.com/itm/Android-10...2349624.m46890.l49286&mkrid=711-127632-2357-0 ) hoping for some support if it broke. Well it's broken and they have only messaged me once suggesting I disconnect and reconnect, which didnt work.
It worked great FOR A DAY until I changed the boot logo and turned on the floating buttons...
Stopped at the store and it's been boot logo ever since.
There is only the RST button (which will and none of the bootloader tricks work.
Pushed 10x
Held 15, 20, 30 seconds, the lights never flash.
I tried the 5 point finger touch and the single finger touch on boot.
I disconnected everything except the power/acc/ground.
At this point I would pay someone to help me because we're on a 35 hour road trip and 21 hours left. I have my laptop and a USB drive if reflashing it is an option.
Finally got some communication from the seller. It is a 9212B Scheme
they don't know anything about entering recovery mode but sent me an update file that does nothing
Hello everyone,
I have a problem:
Out of nowhere, my Head Unit turn the music to the max volume, the button response after a maximum of 10 seconds, then I can turn down the volume. Also sometime, if I press anywhere on the screen, the radio turns off or restarts.
think is something related to the software.
Is there any update for this headunit? i attach some photos of the MCU and system version.
I tried to find the device's name/model and updates, but without success. (I've tried already factory reset).
thanks in advance for thinking along.
Greetz from Amsterdam
Hi, try first disconnecting canbus box if you have it at all on this device. Then start up head unit without canbus and wait for 30 sec then shut down headunit and car engine.
Connect canbus again on the back.
Start in contact mode of car, and as soon as unit starts start tapping on center of screen with all five fingers. When reovery mode activated it will proceed automatically and finish. (procedure will erase data and install again!)
Then try if errors and bugs are fixed.
Hello, just an update. Unfortunately this trick doesn't work. Is there a software update for it?
Ask your seller for solution, probably will be or you must do complete install / flash of ROM memory and install again everything.