Hi Friends,
I dropped my Samsung J7 Pro while using and it and then it's screen went full black and didn't work.
But the phone is on since I was able to hear the ringtone on incoming calls
Questions:
1. Cost for Screen Replacement
2. If I can do it at home by myself what will be required?
3. Can I get order the screen hardware (I assume it's called the touch screen digitizer) from somewhere?
4. No damage to the glass screen itself.
i changed the display just two days back
questions and answers
1. Cost for Screen Replacement -- In indian currency 5200Rs
2. If I can do it at home by myself what will be required? ---- my suggestion is dont replace at home because they are costly ones and if it is broken in your hand you wont be able to replace
3. Can I get order the screen hardware (I assume it's called the touch screen digitizer) from somewhere? -- yeah i wen to an local shop (not a samsung service centre ) they took the phone to near by samsung service centre and replaced the screen due to out of stock and in online you wont be able to find original display i think it will be available in aliexpress or if you are an indian you can order it in maxbhi
4. No damage to the glass screen itself.--- even mine just falled down and the tempered glass even didnt broken but the screen turned into purple color and didnt work its an issue in the diaplays
thank you if you have any doubt whatsapp :8074673011
Related
This is my first post here and though i read similar posts on this subject i would
like to read your opinions on this one.
I accidentally dropped some water on my touch hd and my display got damaged.The phone worked fine and so did the digitizer but the problem was that the backlight of the display was dead.At some point the backlight turned on but when i tried to input the unlock code it turned off right away (did this several times).I knew that i should replace the lcd (and the digitizer just in case).
I bought the lcd and the digitizer seperately and i managed to assemble the phone back using the service manual.Since then when i turn the phone on I hear the starting sound,i get the vibration then after a while the screen with no backlight again displays the "tap here to configure your phone" screen (after the hard reset),when i tap i get no response.
I checked the connections many times and i also used a second digitizer with no success.
Is there a possibility flashing a new ROM will solve the problem?
If so is there a way of flashing a ROM when the phone's screen is not usable?
Waiting for your precious opinions/suggestions/knowledge
Thanks in advance.
Hello,
Flashing the ROM won't solve an obviously hardware problem.
If you changed the LCD and still have no backlight, then either you bought a defective screen, or the problem is elsewhere, maybe on the main electronic board... Which would be bad news.
BTW, I wanted to change the digitizer in the apst years, but its not provided with the glue, so I had to buy a whole assembled screen + digitizer.
How did you manage to glue the digitizer on the screen ?
I aligned the screen with the digitizer and then i used small pieces of a special thin and trasparent tape to hold it in place.The tape holds the screen tight and it is barely visible, it also has the advantage that you can seperate the lcd and digitizer anytime you want with ease (though you have to be very delicate when applying it to get a good result)
I asked for a replacement of the defective lcd and i hope i will get a new one.
Hi,
I had the following problem with my HTC Diamond 2 (it might have got wet & it might possibly have had too much pressure on the screen)
Problem:
The mobile boots ok and the normal buttons at the bottom work fine, as do the volume up/down buttons. The display, however, has what looks like the newton rings and when I press the display it detects a 'press' about 1cm to the left of where i pressed. This means I can't use the right hand side of the display and also can't enter my pin.
Error Diagnosis: (from Arvato Services in Germany)
Mainboard is defect. Cost to repair = € 303.17
Is this possible ? If there was a problem with the mainboard then I would expect to see other problems - and at present, I can only see that the touchscreen has a problem.
Please let me know what you think, thanks in advance !
(ps there should be a question mark at the end of the 'title', don't seem to be able to edit though)
Based on your description and from what I've read, it's definitely the digitizer.
It is possible that you have a damaged board, but regardless, your digitizer is bad.
I would attempt to replace this yourrself then see if everything is fine before sending it to repair.
I had the same problem!
The screen was getting worse in alignment over a time frame of a couple of days. If replaced the digitizer and screen and all is back to normal ..... however it seems to work better then ever before.
The only problem left is dust between the digitizer and my screen, but this is my own fault since I didn't glued the screens. I'll re-open in the next few days and use some silicone to close the gaps. Mainly the volume key has an opening to the outside.
Good luck with the replacement!
Hi
I've dropped my HD2. Everything is working, including touch screen, I can unlock the phone, I can answer the call, but screen is black, not broken.
What should I do? Does the lcd screen replacement will be sufficient? In that case, could the screen be ok, but some other display "processor" could be dead? I'm asking because I'll try to this on my own.
Could simply be the lcd cable has slipped slightly but probably more likely an LCD replacement needed.
You need remove rear housing & have a look & make a decision from your findings/testing.
hello
I've got a little update - lcd screen is working well - I mean it displays the image, the only malfunction is backlit. Right now when i use flashlign I can actually see whats on screen. Do you have experience or think that backlit connection can be repaired? Do You have any schematics for hd2' lcd ?
I suspect new LCD required by sounds of it. LCD can not be stripped for repair so after basic inspection of external connection replacement is only solution & not expensive due to falling cost of HD2 parts.
Hi all ,So the story goes is I had my cracked screen replaced by my insurance 2 months ago. My new screen was fine up until a few week ago when this started happening..
youtu.be/lXv5xBA-r9E[/url]
Basically when I press hard on the top right of the screen I get ghost touches all over the screen. It also happens all the time when I use a case because of the pressure on the top right part of my screen.
I noticed that I can get my fingernail in between the 2 parts of the phone on the side. I really don't want to go a month without my phone again so I'm reluctant to send it off to insurance. Has anyone had this problem? Should I try a phone repair shop? Does this happen if a screen isn't fitted properly or is it another problem? Thanks
Seems like a faulty digitizer
More info... The screen works fine when I press it normally. It only goes crazy and when I press slightly harder or if there is a case on
Hey guys,
broke my Nexus 4 screen a few years ago - now I wanted to replace it just so I have a backup phone.
I removed the glass with some tools, and while doing so another layer at the bottom of the screen came off. (exactly the part that was broken and didnt respond to touches)
It now shows solid white color when the phone is turned on, and I cant find any info wether this layer
is supposed to come off while changing digitizer and glass or not.
Have I borked this completely? Would like to know before I waste money on the Digitizer + Glass instead of just getting a new front frame.
Edit: Okay found out that this is the polarizer which is pretty cheap on the internet.