Help getting QFIL to work with V35 - LG V35 Questions & Answers

Problem:
Have a V35 that just can't seem to be accessed properly by QFIL.
When I try to open partition manager, it stops for a bit and then gives me an error (function: sahara_rx_data:277 Unable to read packet header. Only read 0 bytes)
What I've tried so far:
(from this guide: https://forum.xda-developers.com/lg-v35/development/bootloader-unlock-root-instruction-t4052145)
(also used the V40 thread as reference: https://forum.xda-developers.com/lg-v40/development/unlock-lg-v40-via-9008-root-t-mobile-t4042207)
On PC:
Installed LG Drivers
Installed 9008 Drivers
Installed QPST w/ QFIL (latest version from the QPST website 2.7.480)
On V35 Device: Enabled OEM unlocking and USB debugging
In QFIL: Set file system to UFS, selected the prog_ufs_firehose_Sdm845.elf file for flat build programmer.
I can get the V35 to blank out and device manager shows the QUALCOMM device under ports list.
QFIL can detect the device in the COM port. (I can move the usb cable around and the QFIL program will follow the change of port around)
I've tried updating the drivers on the 9008 driver device on first time use as suggested in the V40 thread.
I've tried uninstalling and reinstalling the 9008 drivers and QPST as suggested in the V40 thread.
I've tried moving to different USB 2.0 ports as suggested in the V40 thread.
I've tried swapping cables twice, including using the original USB A to USB C cable the V35 came with.
One thing I haven't been able to do is assign the search path on "Select Flat Build" bar. I couldn't find any files to download and place in the search path so I assumed it was unnecessary for getting QFIL to work.
Any ideas?

Wild guess, other USB driver interfering?
What CPU and chipset are in your PC?

abuchison said:
Wild guess, other USB driver interfering?
What CPU and chipset are in your PC?
Click to expand...
Click to collapse
Ended up moving to a different PC and doing the following:
1. Install an older version of QPST 2.7.474
2. Update drivers on device manager to change the name of the detected device from the old name to Qualcomm.... 9008
3. Change file system to ufs from emmc.
Could start reading the contents of the device after that. I didn't install LG drivers until I had to connect to adb to call "fastboot oem unlock".

Related

[Q] Missing CDC drivers

I'm trying to install Samsung mobile phone drivers but no matter what I do I miss these drivers when I connect my Samsung Galaxy Y:
CDC Abstract Control Model (ACM)
CDC ACM Data
CDC OBEX Data
CDC Object Exchange (OBEX)
I have googled for solution and I have followed recommended actions (install Kies, install latest drivers, reinstall all, use "have disk" method) on different operating systems (Windows XP, Windows 7) but I got no success.
My phone doesn't boot (I need to flash it with Odin) so I have tried it all in recovery or download mode but I understand it should not really matter as it's Windows issue, not a phone. I'm using original Samsung USB cable.
Could somebody with a working setup could check if they have above devices correctly installed and provide me more information on the driver file? I mean the information from driver details tab in Windows, ie. name of *.SYS file, *.INF file so I could at least check if I have a driver on a disk.
Any other suggestions also welcomed!
Kies is useless & is not required for galaxy y gt-s5360 as it's not supported for firmware flashing on this device so uninstall it
Uninstall any Samsung drivers you have installed from add/remove programmes
Goto my firmware thread at top of Dev section or link in signature
Download & install USB drivers on my thread
Download the firmware from my thread depending on region
Follow the instructions fully
You can manually install drivers if you wish by clicking on unknown device/device with yellow! click have disk & navigate to where you installed Samsung drivers eg c:/programme files/Samsung
It has finally worked (Windows XP)! I have just installed drivers and followed your instructions (with download mode, not recovery mode). Initially I had other unrecognized devices (very generic usb ones) but after a few attempts (usb plug out, usb plug in) the phone has been detected successfully and I managed to flash it. Many thanks!
Sorry, I forgot to mention. I had also removed a battery.
I have the same issue, Could you please paste the links for downloading the drivers.

MK808 Not Recognised By RockChip Batch Tool - Tried Serveral Guides

MK808 not recognised by RockChip Batch Tool - tried serveral guides already
Hello,
I can't flash my MK808 because the RockChip Batch Tool doesn't recognize the device. I tried several guides with no success. I'm on Win7/64
At 1st I followed a guide which I think led me to install the google adb driver. It showed up with "adb devices" but not in the RockChip tool.
I think I was misled here and need the rockchip drivers, don't I?
I downloaded the drivers with Version 3.5 and I also tried the ones which were included in the RockChip Batch Tool (v1.5, v1.6 and v1.8). Windows didn't accept them and kept using the adb or MTP drivers. Now I noticed that in the device manager the MK808 shows as "USB\VID_2207&PID_0001". But in the inf file of the drivers all PIDs were 2xxx or 3xxx. Now just like with the adb driver I added two lines with the ID I got from the device manager. Now the driver is accepted. But I still have no success with the RockChip tool.
I also found a thread which mentions to modify the config.ini of the batch tool but this didn't helped either.
(SUPPORTLOWUSB=TRUE
FULLSPEEDUSB=TRUE)
As I understood I should switch USB debugging off on the device. Than I should go to Settings - USB and click "Connect to PC". Is this right?
Any idea what I might do wrong?
BTW what is the latest firmware for MK808?
thx n rgds
tmg
got it.
Problem was that device was in MTP mode. had to switch it to "mass storage mode". There's another "settings" icon which opens not the standard settinge and there on the "system" tab (?) I could change it. The guid in the web suggest that it could be done in the standard settings, but this didn't worked for my MK808.
usb debugging needs to be off.
At 1st the device is red in the tool. I need to click "switch" to get it green. Wasn't obvious.
1st start seems to take a while ... just came up nice.

Oneplus 5 not recognised in Windows 10

Hi,
I've received a couple of days ago two Onplus 5.
They both work great but when I try to connect them to my desktop, they get detected as "qualcomm hs-usb diagnostics 900e" by windows 10 that states the USB device is not recognised.
The issue is reproduced on a laptop, although it did get picked up once by the laptop, only to fail on a second attempt with the same device name "qualcomm hs-usb diagnostics 900e" after I installed the driver provided by Oneplus.
I read on the forum that "qualcomm hs-usb diagnostics 900e" is normally related to Bricked phone issues, which is not my case and I don't know what to do to resolve this.
I also tried to activate the USB debug mode on the phone, but this didn't change the problem.
My windows are all up to date and my phones as well (running Android 7.1.1, OxygenOS 4.5.2)
Has anyone experienced this issue with that phone or any other?
I would greatly appreciate some help and I thank you in advance for reading this and offering advice.
Unplug phone, restart windows.
Go to settings / about phone / press build number 5-6 time (don't remember exactly how many times) to enable developer options
turn on USB debugging
select USB configuration MTP (media transfer protocol)
plug it in
Install drivers
And now on you should have it working every time you plug it to your laptop.
dcrnic said:
Unplug phone, restart windows.
Go to settings / about phone / press build number 5-6 time (don't remember exactly how many times) to enable developer options
turn on USB debugging
select USB configuration MTP (media transfer protocol)
plug it in
Install drivers
And now on you should have it working every time you plug it to your laptop.
Click to expand...
Click to collapse
Thanks dcrnic, I must have skipped a step with the debugging mode because your procedure did the trick.
Is this a normal process to have to go to Dev mode and Debug mode to be able to connect to a PC?
Thanks again for your help!:good:
Win 10 do not recognize device as it is so new. Probably in the future this will be solved on Windows end.
I found online link for drivers
https://drive.google.com/file/d/0B-LgkimFUEksbjRCY1BkWnduVW8/view?usp=sharing
Moderators
Please delete ... Today forum is so slow, and it do double posting for some reason even I press reply just once.
Thank you.
FIXED: Use stock op5 cable. The other cable that gave me issues works just fine for op2.
The phone used to be seen by win10, but since oem unlock and superSU, the computer at work doesn't recognize it. Ran the 4.5.2 update with same results. I noticed that in Developer Options -> Select USB configurations charging is selected and greyed out. Going in selecting anything else returns is to Charing.
Device Manager > Find the phone > Right click > Update drivers (or something like that) > Select driver from Computer > Select "MTP USB Device" Enjoy
I'm having the same issue. If I manage to get it to connect to the PC, then after I unplug and plug it again it gives the same not recognised balloon. It only seems to work with USB Debugging On
I ended up using the original op5 cable and it recognizes the phone right away.The cable that didn't work for op5 is not stock, but worked perfectly fine for op2.
Same issue
Even I'm facing the exact same issue on my op5
dcrnic said:
Win 10 do not recognize device as it is so new. Probably in the future this will be solved on Windows end.
I found online link for drivers
https://drive.google.com/file/d/0B-LgkimFUEksbjRCY1BkWnduVW8/view?usp=sharing
Click to expand...
Click to collapse
The drivers are on the phone, they're mounted as a drive when you plug the phone in? They even add ADB tools when you install them, they're in C:\Program Files (x86)\OnePlus USB Drivers and the ADB tools are in the Android folder within there.
djsubterrain said:
The drivers are on the phone, they're mounted as a drive when you plug the phone in? They even add ADB tools when you install them, they're in C:\Program Files (x86)\OnePlus USB Drivers and the ADB tools are in the Android folder within there.
Click to expand...
Click to collapse
Yes, they are on the phone, but computer need to recognize device to see it. It does not, so the drivers on the phone are useless in this case.
I compared this to my ZTE Axon 7. If you choose "Charge only" the Axon 7 is recognized as a USB input device. This should also happen for our OP5 but the driver (which btw. is a windows standard driver) does not contain PID 900E and also does not like to have it forced to a USB input device.
The Axon 7's PID is F006.
However, the real issue is when Windows decides to use Qualcomm's HS USB Diagnostic Interface driver which seems to give even more trouble (at least for me). When I tried to switch to MTP this would not work and my Windows 10 hung itself up when rebooting or shuting down. For now I just disabled the "Unknown device" to prevent such things from happening. Charging still works this way and the phone is correctly recognized when changing to MTP.
If you are facing the same issue, disconnect the Oneplus 5 from your PC, reboot the PC and after that launch the device manager. You need to enable hidden devices in the view menu of the device manager to see disconnected devices. Now remove the device "Qualcomm HS USB Device Interface" and also choose to uninstall the driver itself. After that you can connect your device again and it should pop up as "Unknown device". Then simply disable the device.
Regarding the drivers from Oneplus: this package is lacking a driver for the device we are seeing (VID_05C6&PID_900E).
Does anyone know if the latest update (OxygenOS 4.5.5 update) addresses this issue? It says the following as one of the bug fixes:
"To restore connectivity to a Windows 10 PC, please turn off USB debugging prior to the upgrade"
aa_chow said:
Does anyone know if the latest update (OxygenOS 4.5.5 update) addresses this issue? It says the following as one of the bug fixes:
"To restore connectivity to a Windows 10 PC, please turn off USB debugging prior to the upgrade"
Click to expand...
Click to collapse
Worked for me, only remember to Uncheck usb debugging BEFORE the update....
Hmm, didn't work for me, same behavior as before the update...Qualcomm HS-USB as soon as phone is plugged in...USB debug was off.
Sent from my ONEPLUS A5000 using Tapatalk
try changing port (and remember to restart the pc)
Just got my phone today. It updated to 4.5.5 immediately. All I did was connect it to the computer (windows 10) and everything works.
bricky23 said:
Just got my phone today. It updated to 4.5.5 immediately. All I did was connect it to the computer (windows 10) and everything works.
Click to expand...
Click to collapse
It worked the first time too, but not the second time...at that point connected detected as Qualcomm HS-USB Diagnostic, and computer won't shut down.
And yes I installed it a few time, and it works the first time connecting, but not the second time around.
Sent from my ONEPLUS A5000 using Tapatalk
I don't have my OP5 yet, but I had a very similar and difficult experience with my OP3 when I first received it on Windows 10 Pro. On top of installing the proper drivers, I also had to go into Device Manager and run some steps (I'm going off on memory so they may not be entirely accurate). The root cause is driver signature check enforced in Windows 8+. So by going into Device Manager and seeing "kedacom USB driver", right click and find the oneplus USB driver you installed above and also need to disable the driver signature enforcement (in windows 10 go to advanced startup settings, reboot and choose (I think) #7 then reboot). Then plug in the phone usb go to device mgr right click on kedacom USB driver and choose the oneplus driver.
I don't have all the steps in the right order but it should fix your issue.

QPST Memory Dump/Debug Help

Hi there,
I have been attempting to use QPST's memory debug program to dump the phone's memory. Specifically I'm trying to get the ebi_cs1.bin and ebi_cs1.bin files.
My problem is that QPST will detect the phone fine when USB Settings are at RNDIS + DM +Modem or DM + Modem + ADB modes but once I try to run the memory debug app, it requests to put the phone in download mode and QPST will no longer detect the phone when it is in download mode. When the phone is in download mode, it also does not come up with a Comport in device manager (hence QPST can't detect it), but ODIN will actually detect it. I must note that when the phone is on and not in download mode though, QPST and ODIN detect it on different comports.
I have uninstalled and reinstalled Samsung USB drivers numerous times as well as trying different versions of QPST, two different usb cords, and three different usb ports.
If anyone has any idea on how to dump these files with QPST or via alternative methods, please help me!
B.
Any ideas or alternative methods?

QPST driver install...

Trying to get these drivers installed on windows 10 machine but no matter which driver i choose it always pops up "windows encountered an error while installing driver". im trying to get into qpst file explorer to see the policy_man folder for the carrier policy. im on havoc rom 11 and there is no engineer mode(*#801, *#800) or log kit since im not factory rom. ive tried disable driver signature verify under advanced restart on the pc....no luck same error. ive tried disable secure boot in bios on pc....same error.
ive tried these steps......
1. adb reboot ftm
2. Install (in your smartphone) USB Gadget Tool (https://f-droid.org/es/packages/net.tjado.usbgadget/) and check this modes: ( cser.dun.O , diag.diag, diag.diag.mdm , ffs.adb , gsi.dpl , gsi.rmnet , qdss.qdss , qdss.qdss.mdm )
3. adb shell su setprop sys.usb.config diag,diag_mdm,adb
4. Disconnect and connect your phone usb cable.
5. Go to Control Panel – Device Manager. You will see some unknown device. You should look at the so-called "Oneplus 8T", ignore the others.
Right click on the first "Oneplus 8T" –> Update Driver –> Browse my computer drivers -> Let me pick form a list of available drivers -> Click on I Have Disk -> Show all devices, browse then go to the Qualcomm Drivers that you download earlier. Then do the same to the other "Oneplus 8T". Choose 9018 for both unknown "Oneplus 8T"..
6. Add both ports in QPST Configuration. Only one of them is the one you are going to use. By clicking on EFS Explorer you will know which one it is by seeing X55 Driver in the description.
7. Change carrier_policy and carrier_policy.xml_Subscription01 files
8. adb reboot
stuck on step 5
Hmmm... You do have the regular drivers for the device installed as well, correct?
(ADB) works? Try this - (Let me know if you need 32 bit installer) No need to disable driver signing enforcement.
10.99 MB file on MEGA
mega.nz
64bit - If it needs a password it's GADGETSDOCTOR
If you're getting into the use of Qualcomm engineering tools check out the fine work of KL Joachim Schepke and the #u100 Crew to make QXDM5g and the accompanying Tools available, search QXDM5 , also includes driver autoinstaller.
Uninstall the old ones and reboot first, go actually delete the directory, Qcomm doesn't uninstall very cleanly.
Let me know how it goes,
-L4X$
L!V3_4_XC3SS said:
Hmmm... You do have the regular drivers for the device installed as well, correct?
(ADB) works? Try this - (Let me know if you need 32 bit installer) No need to disable driver signing enforcement.
10.99 MB file on MEGA
mega.nz
64bit - If it needs a password it's GADGETSDOCTOR
If you're getting into the use of Qualcomm engineering tools check out the fine work of KL Joachim Schepke and the #u100 Crew to make QXDM5g and the accompanying Tools available, search QXDM5 , also includes driver autoinstaller.
Uninstall the old ones and reboot first, go actually delete the directory, Qcomm doesn't uninstall very cleanly.
Let me know how it goes,
-L4X$
Click to expand...
Click to collapse
Hey thx for the reply....if you mean the oneplus drivers, then yes they are installed on pc and adb works(command prompt and all that).
i uninstalled the old ones and rebooted...downloaded that file and installed....trying now
L!V3_4_XC3SS said:
Hmmm... You do have the regular drivers for the device installed as well, correct?
(ADB) works? Try this - (Let me know if you need 32 bit installer) No need to disable driver signing enforcement.
10.99 MB file on MEGA
mega.nz
64bit - If it needs a password it's GADGETSDOCTOR
If you're getting into the use of Qualcomm engineering tools check out the fine work of KL Joachim Schepke and the #u100 Crew to make QXDM5g and the accompanying Tools available, search QXDM5 , also includes driver autoinstaller.
Uninstall the old ones and reboot first, go actually delete the directory, Qcomm doesn't uninstall very cleanly.
Let me know how it goes,
-L4X$
Click to expand...
Click to collapse
I have tried this and no luck, this is preventing me from using msm to convert my 8t and possibly unbrick if needed. No matter how I install these drivers this is what I get after reboot
"Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)"
msi laptop running windows 10 latest update
JayTheKid said:
I have tried this and no luck, this is preventing me from using msm to convert my 8t and possibly unbrick if needed. No matter how I install these drivers this is what I get after reboot
"Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)"
msi laptop running windows 10 latest update
Click to expand...
Click to collapse
i was able to get device manager to show the device(kb2005) and update/install the driver for that....however, it does not show another kb2005 device, just shows 2 'unknown device'. when i try the update/install driver for the 'unknowns', i get the windows has encountered an error message
with only the one driver installed(shows qualcomm android modem 9018 in device manager under modems tab), i still cant get qpst tools to work without both drivers. in qpst, it shows the correct driver installed as active phones and shows under ports tab....and theres no port to add with add new port
fosgate24360 said:
i was able to get device manager to show the device(kb2005) and update/install the driver for that....however, it does not show another kb2005 device, just shows 2 'unknown device'. when i try the update/install driver for the 'unknowns', i get the windows has encountered an error message
with only the one driver installed(shows qualcomm android modem 9018 in device manager under modems tab), i still cant get qpst tools to work without both drivers. in qpst, it shows the correct driver installed as active phones and shows under ports tab....and theres no port to add with add new port
Click to expand...
Click to collapse
Sorry I was traveling for a little bit - did you get this handled? Sounds to me like you need to make sure that your USB & or wireless debugging is active and not just charging, you can change it on your notifications to transfer files or something like that
L!V3_4_XC3SS said:
Sorry I was traveling for a little bit - did you get this handled? Sounds to me like you need to make sure that your USB & or wireless debugging is active and not just charging, you can change it on your notifications to transfer files or something like that
Click to expand...
Click to collapse
no problem....i was able to get it working thank you. i ended up switching over to android12 evolutionx rom. i had to do that same mod with carrier files and the phone does now pick up 5g signal and 5g icon in stat bar
fosgate24360 said:
Trying to get these drivers installed on windows 10 machine but no matter which driver i choose it always pops up "windows encountered an error while installing driver". im trying to get into qpst file explorer to see the policy_man folder for the carrier policy. im on havoc rom 11 and there is no engineer mode(*#801, *#800) or log kit since im not factory rom. ive tried disable driver signature verify under advanced restart on the pc....no luck same error. ive tried disable secure boot in bios on pc....same error.
ive tried these steps......
1. adb reboot ftm
2. Install (in your smartphone) USB Gadget Tool (https://f-droid.org/es/packages/net.tjado.usbgadget/) and check this modes: ( cser.dun.O , diag.diag, diag.diag.mdm , ffs.adb , gsi.dpl , gsi.rmnet , qdss.qdss , qdss.qdss.mdm )
3. adb shell su setprop sys.usb.config diag,diag_mdm,adb
4. Disconnect and connect your phone usb cable.
5. Go to Control Panel – Device Manager. You will see some unknown device. You should look at the so-called "Oneplus 8T", ignore the others.
Right click on the first "Oneplus 8T" –> Update Driver –> Browse my computer drivers -> Let me pick form a list of available drivers -> Click on I Have Disk -> Show all devices, browse then go to the Qualcomm Drivers that you download earlier. Then do the same to the other "Oneplus 8T". Choose 9018 for both unknown "Oneplus 8T"..
6. Add both ports in QPST Configuration. Only one of them is the one you are going to use. By clicking on EFS Explorer you will know which one it is by seeing X55 Driver in the description.
7. Change carrier_policy and carrier_policy.xml_Subscription01 files
8. adb reboot
stuck on step 5
Click to expand...
Click to collapse
What did you do specifically to get this working? I'm having trouble on Step 5 as well and I can't detect a device.
Xryphon said:
What did you do specifically to get this working? I'm having trouble on Step 5 as well and I can't detect a device.
Click to expand...
Click to collapse
Have you tried disabling Driver Signing Enforcement when booting into Windows and then installing the driver?
Xryphon said:
What did you do specifically to get this working? I'm having trouble on Step 5 as well and I can't detect a device.
Click to expand...
Click to collapse
#3 command should start like this:
adb shell
su
setprop....
Also disable Driver Signing Enforcement, as you'll have to install driver every time you want to use QPST, with it enabled.

Categories

Resources