Related
I know there are already a lot of discussions on battery drain and believe me, I have read every single one of them. However, I think mine is slightly different:
When fully charged and using WIFI for 10 minutes, 10% of juice will be used. Listening to MP3 for 1 hour will also use another 10%. Overall, battery life is really bad but the key is it only happened suddenly. It have been very good up till now.
I have tested this on another battery and have exactly the same results so it is not battery related. I have also hard reset the phone and tested the battery with nothing installed and it still drains. A full charge only lasts me like 4 hour of very light use.
I installed Battlog and the power consumption is around 90 which I think is pretty low, but at times, even with this low consumption, I can see the battery usage literally falling before my eyes, like 5 % in 5 minutes.
I have also tried the HTC battery test, i.e. fully charged the battery, turned on plane mode and full brightness. After one hour, it only used 8% which I thought is normal. However, if I start using the phone by just simply clicking around, it will start dropping.
I believe the phone is fine on standby but once it starts doing things, even simple operations like moving around folders, it starts consuming a lot of power.
This all happens after an overnight charging episode when I noticed that the light stays amber in the morning and the percentage stays at 80%. I soft reset the phone and it immediately show 100%. This has never happen again but my battery usage is never normal since.
All in all, I think it is somehow hardware related, like the battery gauge is bad or the charging is never complete but it still shows green. It is still under warranty but I think will be very difficult to convince the service centre that there is something genuinely wrong with the phone.
P.S. Should also mentioned that I am using the stock telstra rom and have also cycled through the batteries twice before testing.
I had the same problem...
You should try resetting you battery:
1: let your battery drain to 0%
2: fully charge your battery while keeping your phone off!
this solved the problem for me..
Fenixz said:
I had the same problem...
You should try resetting you battery:
1: let your battery drain to 0%
2: fully charge your battery while keeping your phone off!
this solved the problem for me..
Click to expand...
Click to collapse
I had actually "reset" the battery but only drain it to 5% before recharging as I have read that it is not safe to drain to 0%. I'll try to completely drain it tonight and recharge. Will report back.
btw, I noticed that when the battery is charged to 100%, the led stays amber for about 15-20 minutes before turning green. Is this normal or should it turn green immediately after reaching 100%?
Tried completely draining the battery and charge overnight but have no effect. The problem persists. So this is definitely not a battery problem.
I guess the last thing I can try is charging the battery with a standalone charger or another HD to see if there is problem with the charging mechanism in my phone.
The latest Telstra rom seems a bit better on battery
led amber
The led amber must turn to green
immediately after unplugging.
some thing is wrong with your charge
system .
aidinali said:
The led amber must turn to green
immediately after unplugging.
some thing is wrong with your charge
system .
Click to expand...
Click to collapse
aidinali, can you please explain what you mean? I thought the led will go off if you unplugged the charger. My problem is that after reaching 100% as indicated on the phone, the led stays amber for another 15 minutes before turning green.
Well , I'll correct & explain more....
1-when you reach %100 ,the led will turn to green immediately (if you’r phone is plugged in).
2-if you unplug ,the led will turn off (as you said ).
The problem is that since the battery meter in HD has not been defined by percentage , it doesn't match with
Apps like battery level or battlog .so when you see %100 on them , it' s not "real % 100 ".
I believe there is something wrong with the phone as the percentage usage and charging status do not match. However, since the basic HTC software does not have any battery usage in percentage, it’s hard to convince the service centre that something is wrong.
Any software that shows the battery as a percentage all have the same reading, so I assume they all rely on the mainboard for that information. There is obviously something wrong with either the charging process of the phone or draining more battery than it needs during usage.
I have 100% exactly the same problem as in the original post.
Does anyone else?
I have also tried 2 batteries and had exactly the same results with both, so I also know it is not the battery. The only app I have installed other than Dutty's 6.5 rom is Tomtom which does not need to be run for any of these issues to occur.
Any chance on warranty? I think it's software...
Try a different ROM. I've been having the same problem. I just flashed a new ROM about an hour ago (partly because Dutty's 6.5 kept freezing). I'm hoping both problems will be solved now.
i've found the latest radio rom to make a big different to battery life. 1.14.25.24_radio
the previous radio rom (1.13?) did suck the juice and made battery last 2 days less than 1.14
Try charging with a different charger. Ie. connect a USB cable on your PC and charge it from there.
I've had very similar problems with the stock charger a month after i got my TouchHD, and ended up testing with my old P4350 charger and all problems went away.
I've had similar drains even witch WiFi off, no emails, exchange or 3G access...
Now i'm getting a whole day's usage and i'm left with 30-40% battery, with 2 hours average talk time
I've tried with a number of chargers.....battery still sucks.
I've just switched from Dutty's to Energy ROM, radio is 1.14
If anything...energy drains more quickly than Dutty's
It says it drawing 350mA
Ok, I've used Energy ROM but now using Dutty's Leo. The only thing I've loaded so far is Battery Guard which say it's drawing 98mA when on standby(ie....backlight goes off). That'sa massive difference on the 250mA readings I used to get....now all I have todo is figure out which program I'm loading that is killing my battery.
That still only equates to 12 - 13 hours on a good standard battery with no use at all.
samlives said:
Ok, I've used Energy ROM but now using Dutty's Leo. The only thing I've loaded so far is Battery Guard which say it's drawing 98mA when on standby(ie....backlight goes off). That'sa massive difference on the 250mA readings I used to get....now all I have todo is figure out which program I'm loading that is killing my battery.
That still only equates to 12 - 13 hours on a good standard battery with no use at all.
Click to expand...
Click to collapse
Standard battery should last longer. Sounds like your battery may be slightly faulty. Make sure you let battery drain fully before charging, and always try charging with device off. Should help improve strength.
I had same problem when i flashed miri's rom, hd got warm and didn't last, it cooled down in standby, the answer to my problem was that the wifi was not set to save battery mode, once i set it to save power everything was ok
Used 8% in 24 hours
Fallen Spartan said:
Standard battery should last longer. Sounds like your battery may be slightly faulty. Make sure you let battery drain fully before charging, and always try charging with device off. Should help improve strength.
Click to expand...
Click to collapse
Have been trying that for a month now....something seems to have suddenly worked It only used 8% of the battery in 24 hours! I live in the rainforest with no service so cellular was turned off...wifi on, but I only accessed it about 6 times......still,nothing has changed. The same conditions would leave me with a dead battery in 7 hours previously.
Time will tell if it keeps up this well.
By the way....Thanks
So basically you're saying people should drain down the battery to 1% or so and not to 0% (device dies when battery is out) to get a better battery strength?
Seems to be the general consensus. I'm still not sure if that's what made the difference for me but previously,I would put my device to standbye when I went to sleep at 10:30pm and it would be dead by 6am
guys i have been getting very poor battery after i flashed my phone multiple times on a day...
i already tried the calibration app but it did nothing....
now how to wipe battery stats manually??
http://lmgtfy.com/?q=android+wipe+battery+stats+manually
http://forum.xda-developers.com/showpost.php?p=12697960&postcount=3
clarkkov said:
I love lmgtfy! makes me laugh every time!
[email protected]:
When you recalibrate your battery, it takes a few life cycles for the battery to stabilize and for Android to get an accurate reading. First life cycle is alway short. Of course, don't play with ROMs so much it may damage your phones read only memory.
I will post my battery life soon, I'm still waiting for the battery to deplete, I haven't recharged my phone in 4 days now after I calibrated my battery.
Click to expand...
Click to collapse
Wow 4days is huge,iam getting hardly 1day battery after calibrating yesterday....
Actually i removed my phone before getting the 100% notification....
So should i wait for battery to improve???
By the way,when did you calibrate???
Should i calibrate again????
If this wont work i will try terminal emulator method...
So in this method do we need to charge 100% or discharge completely??
Some precautions or just write those commands at any point of charge???
Iam wondering how to thank from the xda app
Thnx to both of u
Sent from my GT-I5801
Same problem here.
Battery drained from 100% to 60% in 3 hours, then to 15% after 5 hours. phone super hot! Widget showed temp 42°C !
Not even used the phone for more than 15 min! REALLY!
Then calibrated before 3 days, now a max of 1 day battery backup only.
Plz help.
And 1 life cycle means I must let the phone charge 100% then let it discharge till it's switched off.
And I should repeat the cycle.correct me if I am wrong.
And I have the habit of not charging to 100% in a single charge session, 2-3 breaks, should I change it?
clarkkov said:
If your phone is hot without you using it, something is running in the background, that shouldn't. Which ROM are you using and which tweaks/fixes have you applied?
One battery life cycle means battery drain from 100% (fully charged) to 1% (fully discharged). Your phone does not have to turn itself off, but make sure it is at 1% when you begin to charge it again. This is important only for a few cycles after calibration, afterwards you are free to charge it as you wish, but while calibrating it's highly recommended that you don't interrupt the charging process (4Hrs).
Click to expand...
Click to collapse
I am using rooted jpd from samfirmware, no fixes except sdcard speed fix, previously it used to give a good battery backup.
And apps do run in background.
Should I set autokill level to high in task killer?
And I will take care of charging.
Thanks for support.
on DDJP2.. getting a horrible backup since i have updated thru KIES. generally on jg6 used to get almost 1.5 days which has come down to 12-16 hours now. trying to calibrate my battery with app 'battery calibration'.. calibrated once.. but still no change. read somewhr that we get the same backup for first few times even after calibrating.. but to get sure i am writing down my process.. plz chk if m doing right or not ..
1. plug in phone with charger
2. wait till 100%.
3. press battery calibration or delete batterystat.bin with the help of root explorer.
4. unplug charger and use it till it discharges completely.
5. charge again to 100%.
plzzzz chk and tell.
plzz someone reply.
I have a question about batery drain. Apps on backgroung are drainning lot of batery? May i have to stop them always?
Send from my Lestatious 1.7 using XDA premium
clarkkov said:
Yes.
You need to be aware that wireless services are draining the battery the most. If you are not using 3G - switch it off, same with BT and WIFI. Widgets that update frequently also drain the battery fast, background data, auto sync services/features are battery killers, too.
Click to expand...
Click to collapse
Thanx for the reply.. i have calibrated once more.. but already showing 80% after hardly 2 hrs.. no clue whats going on... ppl with JP2 shud come up with thr battery backup to get confirmed.
and last thing am waiting for is that someone said .. battery life is worse for first few cycles after the calibration... thats the last hope... :'(
clarkkov said:
Yes.
You need to be aware that wireless services are draining the battery the most. If you are not using 3G - switch it off, same with BT and WIFI. Widgets that update frequently also drain the battery fast, background data, auto sync services/features are battery killers, too.
Sent from the other side
Click to expand...
Click to collapse
Thx for the aswer, i thought that all the background data are drain lot of battery. I'll try to calibrate and switch off all the thing i can and see if my battery lives more time
Hey there,
scince I use BatteryLeftWidget, I can see that my battery voltage only reches 4171mVolt.
So, batterystat.bin delete doesnt help, so anyone an idea where to put the 4200mV ?
Standart disclaimer: I am not responsible if you break things by following this guide, though I will be genuinely surprised if you do.
Credits: This fix is a combination of battery management techniques discussed in the Atrix forums + a technique that I originally found in a Milestone forum (I didn't invent it, but I am too lazy to search who originally posted it ).
This worked in fixing the problem for me (the same problem that I see many others are writing about on the forums), but I can't guarantee it will work for you.
Who should use this? (aka your battery problem symptoms are
1. Battery life on 2.3.4 is significantly worse for you than before.
2. Battery stats are jumping and showing inconsistent information.
3. Your phone loses 30%-60% just by sitting there overnight.
4. Phone idle draining 30%-60% of battery just by sitting there overnight.
5. After flashing a couple of roms, your battery stats got messed up and the phone thinks it's at 100% charge while it's not.
I personally started having battery problems after flashing a couple of roms, applying 1% battery mod and despite flashing jug6ernaut's CWM battery fix.
When I went to bed with a 100% charge, I would wake up to a 50% charge, with Phone Idle process showing up as massacring the battery. The steps below successfully fixed the problem for me.
Prerequisites:
1. Atrix on one of the rooted 2.3.4 roms (ideally,- deodexed and with unlocked CWM)
2. Wall Charger
3. jug6ernaut's CWM battery fix (put it on your SD card you will need it later!) I have also attached it to this post.
4. Battery Calibration app from the market
5. Watchdog Lite or Full from the market
Instructions:
It's best to complete this procedure in the evening before going to bed, so you can leave it at 100% overnight and check in the morning if the drainage issue is fixed!!!
The whole procedure along with recalibration might take up to 5-6 hours!
1. Take the case off your Atrix (one of the latter steps involves taking the battery out from the phone while it's plugged in. Make sure your case won't stand in the way.)
2. Install Battery Calibration app from the market
3. Plug in your Atrix to charge while it's on, wait till it gets to a 100%
4. When the charge is 100%, open the BatteryCalibration app and lookup what the charge is in MV while at 100%. (Explanatory pic, needed number circled in red). Write it down.
My Atrix was showing ~3400MV while at 100%, which is definitely not the maximum capacity.
5. Discharge your Atrix completely until it shuts off.
A good way of doing this quickly is by turning on wifi, and a video player.
6. Without turning on the phone plug it into a wall charger and let it get to 100%
7. When it's at 100%, without unplugging it from the wall charger, take off the battery cover, and take the battery out.
Your phone will "reboot" and show a Missing Battery icon.
8. Without unplugging the phone from the wall charger or turning it on, put the battery back in and wait until the phone recognizes the battery.
9. Your battery should now be recognized by the phone, and showing a charge % significantly lower than 100%.
Mine showed only 5%. Back when I used a Milestone, it usually showed 60% after doing this.
10. Let it sit there charging for 2-3 hours.
My phone wouldn't charge past 10%, but yours might. The numbers don't matter much as the phone is definitely getting additional charge that could have been lost while flashing ROMs, etc.
11. After 2-3 hours, turn the phone on while holding the volume down button and get into CWM.
Do not disconnect it from the charger still!
12. Install jug6ernaut's CWM battery fix (even if you had it installed before), do not reboot yet.
Do not disconnect it from the charger still!
13. Wipe battery stats in CWM, reboot.
Do not disconnect it from the charger still!
14. When the phone turns on, go into BatteryCalibration app again and look up your MV numbers
- if you were like me, they should be significantly higher than before. After this whole process I had 4200MV at 100%, comparing to 3400MV before calibration.
Do not disconnect it from the charger still!
15. Before going to sleep - Install Watchdog from the market. Go into it's preferences, set CPU threshhold to 20%, check "Include phone processes", check "Monitor phone processes", check "Display all phone processes", set system CPU threshhold to 20% as well.
Do not disconnect it from the charger still!
16. Make sure your wifi and data connections are off. Now finally unplug the phone from the charger.
Go to bed, let your phone sleep too.
17. Success! Next morning check where your battery % is at and if you followed the instructions correctly / got lucky like me, your battery life should be 90% or more.
I went to bed with 98% and woke up to 94%. So, I consider this mission a success.
(Your general battery capacity should have increased, even if something still was draining the battery, you will be able to find the infringing process in WatchDog with the settings we've set up in step 15 )
That's all folks! Please report your success / lack of such here. Also, feel free to ask questions, and I along with other users with answer them according to our ability.
I will later add a section on "good practices for battery usage" with tips and tricks.
Cheers!
Attached are screenshots of my results after calibration: This was under moderate usage. Pretty damn good if you ask me.
Post-calibration methods of improving Battery Life
Updated: Post#2 will explain how to solve battery drainage problems when recalibration wasn't enough. It will also explain how battery reporting works, common practices, tips, tricks, etc.
Battery Tips / Tricks / Common Practices
Important things to know:
1. It's important to understand how battery indicator on Android works and how Android manages / reports your battery life. Please read this article:
Your Smartphone’s Battery Gauge is Lying to You (and it’s not such a bad thing)
http://phandroid.com/2010/12/25/you...is-lying-to-you-and-its-not-such-a-bad-thing/
2. Li-ion batteries used in modern smartphones don't have "charge memory". Partial charges won't hurt the battery (e.g. charging from 60% to 80% or from 10% to 50% etc). Feel free to give your phone small charges whenever you have time and need the phone to last longer.
3. Smartphone batteries don't like to be completely discharged or to be kept at 100% capacity for extended periods of time (this actually damages batteries over time). But worry not, the battery software prevents this from happening for you. That's why some of your phones never get to 100% or drop from 100% to 90% minutes after you disconnct the phone from a charger.
4. All batteries gradually lose a small percentage of their capacity after a certain amount of charge cycles. It's a natural part of life. It's always nice to have a spare battery or to purchase a replacement when your current battery isn't to the task anymore.
5. Don't pay much attention to the battery %, just use your phones. I know it's very tempting to track your battery usage every 15 minutes and try to find problems. Been there myself. Thing is, if you do this, you might start thinking you have problems, when you don't have any.
Bottom line - just try to use your phone and not mess with the battery unless problems become really apparent.
------------------------------------------------------------------------------
Other proven ways to improve Battery Life
If you have re-calibrated to a full capacity (4200mv) but your battery still drains terribly - follow these steps to pin point the problem.
1. Find which app / process is draining the battery.
If you get lucky, the infringing app will show up directly under the stock "Battery Usage" statistics. However, in most cases "Battery Usage" isn't very informative. Most people report that they only see "Phone Idle" consuming most of the battery without much insight into the details.
Things to do:
- install Watchdog, go to preferences, set CPU threshhold to 20% (or even lower if it's not enough), check "Include phone processes", check "Monitor phone processes", check "Display all phone processes", set system CPU threshhold to 20%(or even lower if it's not enough) as well. Run it for a couple of days.
If you start getting frequent Watchdog notifications about a certain app breaching the threshold - uninstall it, find an alternative.
- install BetterBatteryStats from here -
http://forum.xda-developers.com/showthread.php?t=1179809 run it for a couple of days and monitor apps / processes that are using up more wakelocks than they should.
Once you find the infringing app - uninstall it, if it's a process - find out if it's safe to stop / freeze before doing anything.
2. Freeze bloatware aka "stop the problem before it becomes a problem."
Unless you are running CM7, your rom is based on stock 2.3.4 and still has blur in it. Blur apps and processes might be running without you even using them and sucking out precious batter life while they are at it.
Things to do:
- Get TitaniumBackup, freeze all bloatware that is mentioned as "safe" in this thread -
http://forum.xda-developers.com/showthread.php?t=1182663
Use your phone for a couple of days afterwards and watch for improvements.
If these software tweaks aren't enough, the problem might be with your system setup. Go through these steps which should hopefully fix your setup in favor of awesome battery life:
3. Flash a custom kernel, set up battery saving profiles.
Many people have reported success with this step. Custom kernels are not just for overclocking. A custom kernel with smart profiles will definitely give definitely extend your phones operating life during the day.
Things to do:
- Get a custom kernel., the popular choice on here seems to be faux'es kernel, so I recommend it -
http://forum.xda-developers.com/showthread.php?t=1156040
Get one of the battery saving SetCpu profiles along with it. Basically, a good battery saving profile looks something like this:
- absolute minimum CPU clock with screen off (something like 275 Mhz)
- lowering CPU clock with temperature > 50C (something like ~800Mhz)
- lowering CPU clock when battery < 30% (something like ~800Mhz)
Many people reported success in using such profile for lowering "Phone Idle" drain.
4. Flash a different radio.
WARNING: Be extremely careful with this. Flashing a wrong radio is the right way to hard brick your phone.
Although some people are reporting to have fixed battery drainage by trying out a different radio, I seriously wouldn't recommend going on a flashing spree unless you know what you are doing.
My advice here: flash the latest 2.3.4 for your carrier if you haven't yet. From there on, experiment at your own risk.
5. Disable Data and Wifi when idle either manually or with an app."
I seriously get surprised every time someone says they have a horrible battery life, when they keep an internet connection on at all times. Constant data always = battery drain.
Things to do:
- use apps like Green Power to disable data / wifi for you when you are not using it
- learn to turn off your internet connection manually
6. If all else fails - start over from scratch (read: clean install a rom).
I've heard reports of people getting better life with Froyo than GB, or that a specific custom ROM solved their problem for them. A million dollar question: if it works for you, why not use it?
Things to do:
- try a ROM without blur, like CM7
- try Ninja Speed Freak (developer and many users reported great battery life)
- if battery life is your top concern - try Froyo
------------------------------------------------------------------------------
FAQ
....coming soon...
... ask away!
Many thanks! Have pass about three days reading about the battery issues/solutions, and I was getting confused by so many info! Will try it tonight!
PS: Does the jug6ernaut's CWM battery fix works for the Orange 2.3.4 ?
eklam said:
Many thanks! Have pass about three days reading about the battery issues/solutions, and I was getting confused by so many info! Will try it tonight!
PS: Does the jug6ernaut's CWM battery fix works for the Orange 2.3.4 ?
Click to expand...
Click to collapse
Are you using stock Orange 2.3.4 rom?
If yes, your Rom might not have the battery jumping problem. You can still use this guide without the battery fix to recalibrate.
Let's wait for someone with Orange 2.3.4 to confirm if jug6ernaut's CWM battery fix can be used or not.
Indeed, I have not the battery jump issue, but I'm exprimenting some weird behavior...
like when I restart the phone, it shows about 10% higher than before. I tried this multiples times yesterday. When it was about 40%, it starts to drop suddenly, 'till it got to 18% and get back to normal decrease to 4%, 2~3 hours later...
See the images attached, the red circles are the times I rebooted it and the blue arrow is when it drops suddenly...
Question on step 4. To confirm, we shouldn't click on anything in BatteryCalibration, all that needs to be done is take note on the MV number, correct?
eklam said:
Indeed, I have not the battery jump issue, but I'm exprimenting some weird behavior...
like when I restart the phone, it shows about 10% higher than before. I tried this multiples times yesterday. When it was about 40%, it starts to drop suddenly, 'till it got to 18% and get back to normal decrease to 4%, 2~3 hours later...
See the images attached, the red circles are the times I rebooted it and the blue arrow is when it drops suddenly...
Click to expand...
Click to collapse
Did it only start doing this on 2.3.4 or you haven't checked before? Anyway, I would do the calibration to see if it changes anything.
coleburns said:
Question on step 4. To confirm, we shouldn't click on anything BatteryCalibration, all that needs to be done is take note on the MV number, correct?
Click to expand...
Click to collapse
No clicking in step 4. Just write down or remember the MV number.
Yes it just starts when updating to 2.3.4... In the first days I got the impression of lower battery level, so reading the forums I saw the restart/level change problem, and tested it
eklam said:
Yes it just starts when updating to 2.3.4... In the first days I got the impression of lower battery level, so reading the forums I saw the restart/level change problem, and tested it
Click to expand...
Click to collapse
You probably updated to 2.3.4 while not at 100% battery level, and it messed up your battery stat. So, yes, do all the steps in this guide except for jug6ernaut's battery fix part.
thanks, ill give this a shot....again.....tonight and hopefully it will fix my issue.
Screenshots of results added to post 1
Download link seems to be down...just errors out when trying to download.
Sent from my MB860 using XDA App
jarsh92 said:
Download link seems to be down...just errors out when trying to download.
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
Which download link? CMW_Jug6_FIXv2.zip?
I'm on a rooted stock GB and I'm having the problem where the battery usage stats are inaccurate and won't got below 90% after using it all day. This all started after I used Battery Calibration. Do you think that this would help correct the problem?
Edit: Also, would I need to complete all of the steps including the CWM part? I haven't flashed any roms yet, so I don't know if this would be necessary.
ThickG said:
I'm on a rooted stock GB and I'm having the problem where the battery usage stats are inaccurate and won't got below 90% after using it all day. This all started after I used Battery Calibration. Do you think that this would help correct the problem?
Edit: Also, would I need to complete all of the steps including the CWM part? I haven't flashed any roms yet, so I don't know if this would be necessary.
Click to expand...
Click to collapse
Seems like you used Battery Calibration while not at 100% charge and your battery stats got messed up.
The reason I recommend using CWM is because the battery stats file is created on each boot. So, with my instructions you can charge the phone to 100% while it's off and wipe the messed up stats before it boots.
You can try using my instructions, without the CWM part, except you need to wipe your battery stats with Battery Calibration app after step 4.
lol i left pandora on since this morning and its only at 67%. ugh, when i wanna force drain the battery it goes slow as hell but when i wanna conserve battery live for usage it drains quick. hahaha.
I just flashed navalynt's πCrust rom fully charged, cleared stats through cwm, booted and now i'm close to 3days.
dictoresno said:
lol i left pandora on since this morning and its only at 67%. ugh, when i wanna force drain the battery it goes slow as hell but when i wanna conserve battery live for usage it drains quick. hahaha.
Click to expand...
Click to collapse
lol yes. I used video playback to drain mine. But if it's really a PITA, you can always just leave it till tomorrow to discharge naturally.
Jonous said:
I just flashed navalynt's πCrust rom fully charged, cleared stats through cwm, booted and now i'm close to 3days.
Click to expand...
Click to collapse
Yep, that's why flashing only when at 100% charge always pays off.
I get the same results by booting to CWM, wiping battery stats, rebooting, starting Battery Calibration, plugging phone into wall charger, charging to 100% (4197mv for me), and then calibrating with Battery Calibration. I start this process at any battery percentage, and have been doing this for a long time now. I have never had to deplete my battery until my phone shuts off, and get great battery life.
Beamed from WinBorg 4G via XDA Premium
CaelanT said:
I get the same results by booting to CWM, wiping battery stats, rebooting, starting Battery Calibration, plugging phone into wall charger, charging to 100% (4197mv for me), and then calibrating with Battery Calibration. I start this process at any battery percentage, and have been doing this for a long time now. I have never had to deplete my battery until my phone shuts off, and get great battery life.
Beamed from WinBorg 4G via XDA Premium
Click to expand...
Click to collapse
After the calibration I had 4200mv, so it seems like you are doing things right in regards to the battery.
"Taking the battery out and putting it back in" trick works wonders though in restoring battery life to maximum state (if you had it decrease for some reason). I've tested it multiple times even back when I had the Milestone.
So, I am using MIUI 2.1.12 with LorDModUE 8.6 CFS 2WCR kernel.
I have installed 4EXT Recovery Controller and CurrentWidget.
With CurrentWidget, I monitored the battery while charging until it reached 0mA (which means the battery is as full as it can get).
With 4EXT Recovery Controller I removed the batterystats.bin file.
I drained the phone until it shut itself down. Then I charged it (without powering it on) until it was full (LED was green).
I power on the phone... 99% battery.
I plug in the charger... it says 26mA (which means it would reach 0mA as in full charge in another 20-30 minutes).
WHAT THE HELL?!
This never happened while I was using the default CM kernel included in MIUI. Only happened with Tiamat and LordMod.
--
Seriously, guys, what is the best way to calibrate the battery?! Perhaps I should not have let it shut itself down, but plug the charger when the phone was at 1% (which lasted for another 20-30 minutes, by the way)?!
if I don't remember it wrong the LED turns green at 90%.
afair the battery doesn't get charged during booting. which means that you probably lost the 1% during boot.
I also used the same method and got it calibrated correctly
but is their any other way too ?
monki79 said:
if I don't remember it wrong the LED turns green at 90%.
Click to expand...
Click to collapse
The LED turns green on AOSP ROMs at 90%, when the phone is ON, as far as I know. When it is OFF, it works fine (goes green at 100%).
I want to hear from the developers / those that know how these codes work and stuff... Cause I don't want to look at my phone how the percentage goes down so fast, then, when it reaches 10%, I can play Pocket Legends for another 20 full minutes -.-
Formhault said:
With CurrentWidget, I monitored the battery while charging until it reached 0mA (which means the battery is as full as it can get).
With 4EXT Recovery Controller I removed the batterystats.bin file.
I drained the phone until it shut itself down. Then I charged it (without powering it on) until it was full (LED was green).
I power on the phone... 99% battery.
I plug in the charger... it says 26mA (which means it would reach 0mA as in full charge in another 20-30 minutes).
WHAT THE HELL?!
Click to expand...
Click to collapse
The battery doesn't charge to full capacity first time around. When I used to calibrate the battery I would charge until it was drawing 0mA, then reboot; it would be drawing about 26mA, so I'd charge to 0mA again and reboot; it would now be drawing about 15mA, so I'd carry on charging to 0mA, reboot, repeat, repeat and repeat until it eventually continued to draw 0mA after a reboot. Then I'd delete the batterystats.bin file.
As one of Google's engineers says, deleting your battery stats isn't going to improve your battery life. I haven't done any of that for a long time now and I've noticed precisely no difference (except for the extra time I've gained by not having to wait for it to finally charge up to full capacity).
hopscotchjunkie said:
The battery doesn't charge to full capacity first time around. When I used to calibrate the battery I would charge until it was drawing 0mA, then reboot; it would be drawing about 26mA, so I'd charge to 0mA again and reboot; it would now be drawing about 15mA, so I'd carry on charging to 0mA, reboot, repeat, repeat and repeat until it eventually continued to draw 0mA after a reboot. Then I'd delete the batterystats.bin file.
As one of Google's engineers says, deleting your battery stats isn't going to improve your battery life. I haven't done any of that for a long time now and I've noticed precisely no difference (except for the extra time I've gained by not having to wait for it to finally charge up to full capacity).
Click to expand...
Click to collapse
I know about Google's statement.
The battery would drain fast, then, when it reaches 1% or 5%, you would be able to use your phone like it had 30%. Just that it shows the values wrong. Calibrating the battery should fix that...
Anyway... I'm not going to struggle any further.
I'll tell what I've done;
- I have installed Battery Balibration app and CurrentWidget,
- Waited battery charging till reached 0ma,
- Removed battery stats and restarted,
- Then waited to drain battery and shut-down itself,
- I connected USB charger to PC and TURN ON THE PHONE !!
- Again waited battery to reach 0 ma,
- Then plugged off and monitored that current widget shows the range btw 3-10 !!
I don't know exactly if it helps but, maybe you should turn on your DHD while carging..
For further instructions you may qant to check this topic;
http://forum.xda-developers.com/showthread.php?t=1226016
Formhault said:
So, I am using MIUI 2.1.12 with LorDModUE 8.6 CFS 2WCR kernel.
I have installed 4EXT Recovery Controller and CurrentWidget.
With CurrentWidget, I monitored the battery while charging until it reached 0mA (which means the battery is as full as it can get).
With 4EXT Recovery Controller I removed the batterystats.bin file.
I drained the phone until it shut itself down. Then I charged it (without powering it on) until it was full (LED was green).
I power on the phone... 99% battery.
I plug in the charger... it says 26mA (which means it would reach 0mA as in full charge in another 20-30 minutes).
WHAT THE HELL?!
This never happened while I was using the default CM kernel included in MIUI. Only happened with Tiamat and LordMod.
--
Seriously, guys, what is the best way to calibrate the battery?! Perhaps I should not have let it shut itself down, but plug the charger when the phone was at 1% (which lasted for another 20-30 minutes, by the way)?!
Click to expand...
Click to collapse
Theres a better alternative, use the battery calibration app in the market
https://market.android.com/details?id=com.nema.batterycalibration&hl=en
It's always worked a charm for me.
knp3385 said:
Theres a better alternative, use the battery calibration app in the market
https://market.android.com/details?id=com.nema.batterycalibration&hl=en
It's always worked a charm for me.
Click to expand...
Click to collapse
Right, with Battery Calibration i have solved my problem with battery, now i can use all day without charging.
Sorry if my question is a silly one...
what's the point in calibrating your battery? I mean... except for the stats (and I guess, the percentage in the bar), do you improve your battery life by calibrating it?
Duwie_80 said:
Sorry if my question is a silly one...
what's the point in calibrating your battery? I mean... except for the stats (and I guess, the percentage in the bar), do you improve your battery life by calibrating it?
Click to expand...
Click to collapse
Some says it's irrelevant, calibrating it's just an illusion
But did calibrate my battery and my battery life is improved too terrific !!
Duwie_80 said:
Sorry if my question is a silly one...
what's the point in calibrating your battery? I mean... except for the stats (and I guess, the percentage in the bar), do you improve your battery life by calibrating it?
Click to expand...
Click to collapse
fremce said:
Some says it's irrelevant, calibrating it's just an illusion
But did calibrate my battery and my battery life is improved too terrific !!
Click to expand...
Click to collapse
I don't really know. It would be silly for the Android system to display the battery percentage (up there, in the status bar) by reading the batterystats.bin.
My phone's battery level drops somewhat fast, then, when it would reach 30% or so, it doesn't drop as fast. Also, at times, when I reach 10%, 5% or even 1%, I am still able to play an intensive game like Pocket Legends for an extended ammount of time (30 minutes, for example). Pocket Legends is CPU/GPU intensive and it also requires an active Internet connection, so I'd say it's pretty power hungry.
I don't really get the entire purpose of calibration. I have done it and I can't seem to notice any difference.
I'm going to do it again, now, because I switched to a Sense ROM (RunnyDrOiD). I'll monitor the battery with Battery Monitor Pro. When it reaches +0mA, I'll reboot and so forth so forth until it's drawing 0mA, although I doubt I'll resist that much time, so I'll just delete the batterystats.bin after a few reboots, when it reachs 0mA.
fremce said:
Some says it's irrelevant, calibrating it's just an illusion
But did calibrate my battery and my battery life is improved too terrific !!
Click to expand...
Click to collapse
If everybody knew the meaning of the word "calibration" then nobody would talk such nonsense.
Calibration improves the accuracy of the percentage shown!
The illusion is that you improve your battery life with it....
Dlog said:
If everybody knew the meaning of the word "calibration" then nobody would talk such nonsense.
Calibration improves the accuracy of the percentage shown!
The illusion is that you improve your battery life with it....
Click to expand...
Click to collapse
As I said... calibrating the battery may fix the "problem" where once you reach 1% / 5% you can use your phone like it still had ~20%.
I'm gone test it too...
Hi there people, I didn't find any battery thread similar to what I'm going to say so I'll spam a little bit
I've just found as I was fooling around this: http://www.ebay.com.au/itm/PowerSki...AU_MobilePhoneAccessories&hash=item20c1a1c8ad
It suppose to be a silicon case with a battery build in(1500mah ..not bad), I don't know the dimensions but I just someone might think it as a solution to our 1230mah small battery(with this you have a total of 1730mah which is plenty)
P.S. To mods.. feel free to delete my post, I just wanted to inform the people about a solution that might be handy
evronetwork said:
Hi there people, I didn't find any battery thread similar to what I'm going to say so I'll spam a little bit
I've just found as I was fooling around this: http://www.ebay.com.au/itm/PowerSki...AU_MobilePhoneAccessories&hash=item20c1a1c8ad
It suppose to be a silicon case with a battery build in(1500mah ..not bad), I don't know the dimensions but I just someone might think it as a solution to our 1230mah small battery(with this you have a total of 1730mah which is plenty)
P.S. To mods.. feel free to delete my post, I just wanted to inform the people about a solution that might be handy
Click to expand...
Click to collapse
https://www.google.com/search?q=xda+powerskin+desire+hd
first link....
Hey everyone. So I bought a second hand note 4 recently and have been having battery problems.
I did a full wipe install of CM13 and the battery dropped to 0% at random times and I had to plug it in the charger for the phone to even boot as it would just restart as soon as it turned on. Anyway, i thought this is probably due to faulty battery. I purchased another one and now this one doesn't reboot at random times but seems like the phone keeps reading the battery percentage wrong, sometimes it doesn't charge over certain percent, just gets stuck at 77% or 63% or any percentage really. If I remove the battery and plug it back in, it shows a completely different percentage everytime. I have tried wiping battery stats, do a full discharge/charge, nothing seems to help. Battery drains fairly fast too, once I manage to get it to 100% it shows that expected time is like 2-3hrs if screen on. Thanks!
idoluvizsick said:
Hey everyone. So I bought a second hand note 4 recently and have been having battery problems.
I did a full wipe install of CM13 and the battery dropped to 0% at random times and I had to plug it in the charger for the phone to even boot as it would just restart as soon as it turned on. Anyway, i thought this is probably due to faulty battery. I purchased another one and now this one doesn't reboot at random times but seems like the phone keeps reading the battery percentage wrong, sometimes it doesn't charge over certain percent, just gets stuck at 77% or 63% or any percentage really. If I remove the battery and plug it back in, it shows a completely different percentage everytime. I have tried wiping battery stats, do a full discharge/charge, nothing seems to help. Battery drains fairly fast too, once I manage to get it to 100% it shows that expected time is like 2-3hrs if screen on. Thanks!
Click to expand...
Click to collapse
battery displaying different percentage after u remove it and put it back in is normal i have 3 note4s all do the same (up to 10 percentage change, it either increases or decreases) but the other issues like getting stuck on a certain percentage are not normal make sure u have the genuine battery and try stock rom.
yeah, i tried stock and the same thing really. such a random issue. I just noticed that battery charges once I turn the screen on and use it , so it only gets stuck on random percent only with screen off.
idoluvizsick said:
yeah, i tried stock and the same thing really. such a random issue. I just noticed that battery charges once I turn the screen on and use it , so it only gets stuck on random percent only with screen off.
Click to expand...
Click to collapse
U can try recalibraring the battery....
Bishal 00 said:
U can try recalibraring the battery....
Click to expand...
Click to collapse
yeah, i said I wiped battery stats, which is basically recalibration
once the battery is charged to 100% it also drops first 10-20% really fast and then it gets better but still I only get around 2hrs screen time
idoluvizsick said:
yeah, i said I wiped battery stats, which is basically recalibration
Click to expand...
Click to collapse
Oops my bad..Didn't read your whole post...
the only way to fix this replace your battery by new one
i tried all options (Format ROM - Wipe battery status - Getting back to stock ROM - Unroot - re Celebrate apps - Changing recovery-Removing battery from device for while sleeping - charge without fast charge - charge via USB)
i asked myself after that all of this headache doesn't worth 20$, i replaced the battery with new one and its working fine now
A0_o said:
the only way to fix this replace your battery by new one
i tried all options (Format ROM - Wipe battery status - Getting back to stock ROM - Unroot - re Celebrate apps - Changing recovery-Removing battery from device for while sleeping - charge without fast charge - charge via USB)
i asked myself after that all of this headache doesn't worth 20$, i replaced the battery with new one and its working fine now
Click to expand...
Click to collapse
yeah, i replaced battery as well but it's still the same issue. old one at least charged fully but would randomly reboot on me, the new one doesn't reboot but drains extra fast and doesn't always charge fully. can't believe both batteries are faulty
I am sorry for summoning this old post but did you find any solution to your problem? I have exactly the same experience with my note 4.
Thanks!
Is there a solution for this problem?
Power down and then out-and-in same battery and my stuck-at78%... was 100% when started.
if you having problems with auto restarting.... download the app " WAKE LOCK" and put it on Partial Wake Lock setting... your restarts will be a thing of the past.