Hello, I have change my screen with frame my problem is that I were on rr by flyinwind, after screen change all is good but when I press power the screen switch off and no way to make it on until reboot, digitizer work but all is black. I've try different custom rom always same thing. On oos all is great, maybe some driver. Maybe some guy have an idea?
bretzelpopo said:
Hello, I have change my screen with frame my problem is that I were on rr by flyinwind, after screen change all is good but when I press power the screen switch off and no way to make it on until reboot, digitizer work but all is black. I've try different custom rom always same thing. On oos all is great, maybe some driver. Maybe some guy have an idea?
Click to expand...
Click to collapse
I think it happens cause of a cheap display screen. Same thing happened to me, gonna buy some "premium" display and will let you know.
Yeah because of not manufacturer LCD,for the moment stay with oos . All gesture screen off don't work even dt2w
Related
aright previously my LCD screen was cracked well i got the replacement LCD screen and it works fine. BUT my problem now is that its just displaying a white screen. Nothing else. I take off the battery put it back on turn the phone on and i get a white screen no letters no nothing.
Does this mean my phone is a brick?
i still get response when i hold down the comm button it vibrates. The volume slider responds with the volume going up and down. and when i try to hard reset via holding the comm button,voicebutton,camera button and hitting the soft reset button it responds to it and resets the phone apparantly.
So i know for a fact the actual phone works..but its not displaying anything but a white screen...is there anything else i can do ?
If you have replaced the screen yourself, it may be worth trying to re-fit it again. Make sure the connectors are in pefectly, and make sure there is no dirt on them. If the pda still responds to button presses, it's fine, it's only the srcreen that's damaged/non-functional...
To see if this is the case, try tapping on the very to left of the screen, and see if you get the start menu pop. If you don't it's prolly the connector not plugged in properly, if you do, then the connector may be damaged...
ok im trying now..but how could it be the screen if the screen is giving me a perfectly white screen and its been tested to be working correctly?
sweeet i reconnected everything and it worked thanks for the recommendation dood much appreciated
sojiroxiii said:
sweeet i reconnected everything and it worked thanks for the recommendation dood much appreciated
Click to expand...
Click to collapse
Nice to see that my reccomendation worked for you. I've never replaced a colour LCD screen before, but some of the B&W ones i've replaced have had similar faults. It's the same with old cartridge games if you think about it, you used to have to blow on them ocasionally...
Modern technology may be perfect in every respect, but the manufacturing methods arn't.
Whenever i slide out the keyboard the screen either becomes unresponsive or blacks out. I tried flashing two diff roms from itje and smaberg but they both have the same problem. The screen also becomes very inaccurate and unresponsive. Anyone have such problems?
Nope, here is fine.
The question - does the situation STAY this way or just happens for a few seconds?
Now the screen doesnt even work, when i slide out the keyboard the whole screen blanks out.
custom rom?
Exactly.
The questions:
1. Do you use custom ROM's?
2. Or what did you install
Also
3. Did your phone falled down? I mean - it may be a mechanical problem with connection with 2 parts of the device, no?
I've tried 2 custom now im back on the official one, looks like its going to the service centre. I think its a mechanical problem. When the keyboard is slid out, the screen appears to power down with some colours appearing, when it is in fact still on.
I think the magnet of your x1 has some problem,as we all know,system determine the keyboard sliding by magnetic induction,
and here is a way to test it,you can put you x1 on somethings which has a big magnet, if x1's screen rotate, I think magnet of your x1 has some problem or lose,
I sent it to service center. Hope it gets fixed well.
I keep having this problem with almost every build I try in my TMO HD2. When holding the phone, as soon as I make a call, the screen goes black. When I end the call using the hardware button, the keypad lights come on and the screen is non responsive until I plug in the charger. Solution?
I too have this problem but not that bad.After ending the call the screen stays black for 3-4 seconds, but it is still irritating.
Well mine stays black until I insert the charger which renders any of the builds with the issue completley unusable.
this is already known problem, especialy with DesireHD build it gets worst. there is no solution yet, as I understood, but several workarounds, for example discussed in this thread
http://forum.xda-developers.com/showthread.php?t=835127
I always say it but maybe trying a different build would work?
brinks said:
Well mine stays black until I insert the charger which renders any of the builds with the issue completley unusable.
Click to expand...
Click to collapse
Do you have BsB Tweaks installed? If so, this problem is caused by having the "Tap Time" tweak set to "on". I was having this issue and read about the fix somewhere (might have been here). I set "Tap Time" to "off" and.... immediate and permanent (so far, about a week) fix.
regards
noshad
brinks said:
I keep having this problem with almost every build I try in my TMO HD2. When holding the phone, as soon as I make a call, the screen goes black. When I end the call using the hardware button, the keypad lights come on and the screen is non responsive until I plug in the charger. Solution?
Click to expand...
Click to collapse
Do you have BsB Tweaks installed? If so, this problem is caused by having the "Tap Time" tweak set to "on". I was having this issue and read about the fix somewhere (might have been here). I set "Tap Time" to "off" and.... immediate and permanent (so far, about a week) fix.
regards
noshad
EndCall - black screen freez
same problem here... please help me !
i had installed on my hd2 DL.Desire.v4.31.44.12 and it's worked fine for a wile but now i tryed the last version of dl desire and a gingerbread build but the problem didn't disapear. I reinstalled radio that is version 2.15.50.14 but .. nothing seams to work
I need your help guys !
Sorry for my bad english.
I was curious to see if in wmo it is the same problem, but no... in wmo works fine.
it's strange that at first fresh install of dl.desire everything was ok, but now it isn't. I've reinstalled magldr but with the same results.
It doesen't work.
I think it is something with the proximity sensor, because when i turn on the speaker and the screen is on i can end the call with no problem and no freeze.
the only solution i have for now to unfreeze the screen is to plug in the charger cable in the device.
Problem Solved
I just cleaned the proximity sensor and it's working great. No freeze no black screen.
I have the same problem.
http://forum.xda-developers.com/showthread.php?t=1012396
If you have the original screen protector with the 2 holes from htc, try to clean the sensors with a soft microfiber.
I didn't had this problem untill i replaced my screen protector with the htc screen protector. (the 2 little holes are exposed to dust and dirt, and when you remove the phone from your ear the sensor doesn't respond because of dirt. I think in android the voltage for sensors is a little bit lower than wmo, and that makes the sensor less responsive)
Sorry for my english.
install from android market ADW launcher....make it default home screen...try this one too..
Solution
Everything difficult-is easier)
Just clean dust on the sreen,where sensor is situated.
Hy folks,
I noticed with great anticipation that there are now ROMs available (2.3/2.2) that support Screen calibration. I Tested everyone of them and they all have the same behavior.
My phone got a 7mm strip on the right site that isnt working when the isnt calibrated. After a calibration with a 2.1 stock ROM everything is fine (naturally).
When i calibrate the screen with one of that fancy new roms there is a strange behavior:
The strip i mentioned isnt working, BUT: if i start scrolling the menu in the middle of the Screen and move my finger to that dead strip while scrolling it works. If i stop the scrolling and try to use the known to be dead spot it isnt working.
So the spot that is dead when the screen isnt calibrated only works with that new roms when the touchscreen is "in use" and move i to that spot.
Anyone got a similar behavior?
pythoner said:
Hy folks,
I noticed with great anticipation that there are now ROMs available (2.3/2.2) that support Screen calibration. I Tested everyone of them and they all have the same behavior.
My phone got a 7mm strip on the right site that isnt working when the isnt calibrated. After a calibration with a 2.1 stock ROM everything is fine (naturally).
When i calibrate the screen with one of that fancy new roms there is a strange behavior:
The strip i mentioned isnt working, BUT: if i start scrolling the menu in the middle of the Screen and move my finger to that dead strip while scrolling it works. If i stop the scrolling and try to use the known to be dead spot it isnt working.
So the spot that is dead when the screen isnt calibrated only works with that new roms when the touchscreen is "in use" and move i to that spot.
Anyone got a similar behavior?
Click to expand...
Click to collapse
Are you referring to the blank, undetectable spot between the menu and back button?
I dont know hoy you hold your Phone, but i dont hold mine like a Phone for me the Back and Menu Buttons are down and not to the right
Between Menu and black buttons it's not a touchscreen space. "Back" and "Menu" button is a hardware button, has another connector.
And yes, i most rom's Screen Calibration is just and not working apk. You can see in logcat error, if the calibration not work. I saw that in mine rom, so at weekend I will try to fix it.
pebe94 said:
Between Menu and black buttons it's not a touchscreen space. "Back" and "Menu" button is a hardware button, has another connector.
And yes, i most rom's Screen Calibration is just and not working apk. You can see in logcat error, if the calibration not work. I saw that in mine rom, so at weekend I will try to fix it.
Click to expand...
Click to collapse
That would be more than awesome!
i have a S6 Edge+ and its got a cracked screen. it has a big black spot the size of a fingertip on the right middle like something stabbed it maybe.
sometimes when i got to wake it up, phone is on and i press the power button the lights on the bottom come on, the cascade window button and the back button............but the screen does not light up. it kind of flickers and i see the permanent damaged part, a green strip down the right side of screen but does not turn on.
sometimes i have to press the power button to wake up and put to sleep 6 or 10 times for the screen to light up.
my question:
do you think this is simply from the screen being damaged.
have you seen anything like this before on a phone
do you think if i spend the money to fix the screen this issue will be fixed?
cnile said:
i have a S6 Edge+ and its got a cracked screen. it has a big black spot the size of a fingertip on the right middle like something stabbed it maybe.
sometimes when i got to wake it up, phone is on and i press the power button the lights on the bottom come on, the cascade window button and the back button............but the screen does not light up. it kind of flickers and i see the permanent damaged part, a green strip down the right side of screen but does not turn on.
sometimes i have to press the power button to wake up and put to sleep 6 or 10 times for the screen to light up.
my question:
do you think this is simply from the screen being damaged.
have you seen anything like this before on a phone
do you think if i spend the money to fix the screen this issue will be fixed?
Click to expand...
Click to collapse
Yes.
Yes, on my son's Xperia Z5 Compact. He hadn't dropped it or damaged it in any way - just happened.
Yes
B3311 said:
Yes.
Yes, on my son's Xperia Z5 Compact. He hadn't dropped it or damaged it in any way - just happened.
Yes
Click to expand...
Click to collapse
Any solution or anything you tried?
cnile said:
Any solution or anything you tried?
Click to expand...
Click to collapse
Fixed by Sony, phone is insured.
Yes, take it to Samsung store to repairing.
Ok, I have booted into safe mode and the problem does not exist. this means its a sofware issue, obviously. Here is the dilemma, I have done factory and hard resets to include the cache partition. How might i go about fixing this issue until they release a new update from android 5.1.1???
Can anybody tell me what core we use to put the touchwiz snappier, I saw one one topic but I can't find it now. We only have to put the code and the phone was so quick like the day we Unbox the phone. Thanks